AudioSource IW Six/S Hooking Up The Wires, Mounting the Speaker, Installing The Grille

Page 2

Hooking Up The Wires

The terminals will accommodate up to 16-gauge speaker wire, which should be used for longer connections (greater than 50 feet of wire). For shorter distances, 18 or 20 gauge speaker wire will be adequate. Leave about two feet of extra wire at the speaker end to make installation and positioning of the speaker easier. Do not use staples, nails or other metal objects to secure the speaker wire. The resulting short circuit could affect your system's performance, and could also damage components in your system, especially the amplifier. You will get the best sound quality and least amount of hum by keeping the speaker wires away from other electrical wires and cables.

When connecting your in-wall speaker, it is very important to retain the correct polarity. To do this, be sure that the wire attached to the "+" , red, positive, or hot terminal on the speaker connects to the "+", red, positive or hot terminal on the other component. Similarly, the "-", black, negative or ground terminal on the speaker must connect to the respective "-", black, negative or ground terminal on the other component.

Mounting the Speaker

Yes, you will be cutting a hole in the wall. With the right tools and a little extra care and preparation, installing the in-wall speaker can be both quick and easy. Carefully cut out the hole drawn on the paper template at the perforated edge labeled “CUT HERE FOR MOUNTING TEMPLATE”. (Note: The inside rectangle on the template can be used to shield the woofer while you paint the frame.) Next, position the template (now a border) where you have chosen to mount the speaker, and trace along the inside edge. Make your cuts along this line. A utility knife will make the cleanest cuts in drywall. A keyhole saw or an electric jigsaw may also be used. Try to keep the cuts neat, however the frame will overlap the hole to hide any rough edges. At this point, with the wall open, run the speaker wires into position, and again, leave about two feet of extra wire at the opening.

Remove the grille from the frame by pressing the quick-turn mounting screws from the back of the speaker into the grille itself. Remove the thin piece of foam positioned under the grille, which was used to protect the speaker during transport. Position the swivel tweeter so that it points toward the place in which you will be listening to the speakers.

Attach the speaker wires to the speaker. With the grille removed, insert the speaker into the mounting hole. Use a phillips head screw- driver to turn the screw slowly clockwise. The quick-turn mounting system and frame will sandwich or clamp around the wall to hold the speaker in place. Do not overtighten. If you are unsure, consult a professional contractor.

Installing The Grille

The metal grille, as well as the frame, may be painted to match any room. If you choose to paint them, do so before attaching the grille to the speaker. The grille is held in place by a friction fit and is difficult to remove once the speaker is installed. If the grille feels a little loose, or you are concerned about a grille falling from a ceiling installation, we have provided a small amount of putty, which you can apply (sparingly) to the inside rim of the speaker before you insert the grille. The putty acts as an additional adhesive between the grille and the frame.

IW Six/S Specifications

Frequency Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Hz to 24 kHz

Power Capacity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 watts

Impedance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 ohms

Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 dB

Woofer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 612” polypropylene

Tweeter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1” swivel

Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1312" x 914 x 3"

Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 lbs.

Design and specifications are subject to change without notice.

9300 North Decatur

 

Portland, OR 97203

 

Tel. 503.286.9300

 

Fax 503.978.3302

 

audiosource@Phoenixgold.com

 

www.audiosource.net

© 2000 AudioSource, Inc.

Image 2
Contents In-Wall Speakers Speaker PlacementIW Six/S IW Six/S Specifications Hooking Up The WiresInstalling The Grille Mounting the Speaker

IW Six/S specifications

The AudioSource IW Six/S is a cutting-edge in-wall speaker designed for audiophiles seeking discreet yet powerful sound solutions in their home audio systems. Engineered with precision, the IW Six/S combines advanced technologies and features to deliver an immersive listening experience that seamlessly blends with any interior design.

One of the standout characteristics of the IW Six/S is its robust build quality. The speaker features a durable enclosure which helps to minimize resonance and distortion, ensuring clarity across all audio frequencies. The high-quality components used in the IW Six/S further enhance the listening experience, offering deep bass response alongside crisp high frequencies. The 6.5-inch polypropylene woofer is designed for maximum efficiency, providing excellent low-frequency output, while the 1-inch pivoting tweeter allows for optimal sound dispersion and targeted audio placement.

Another key feature of the IW Six/S is its easy installation process. The speaker is designed for standard wall cavities, making it a versatile choice for both new builds and retrofits. The included mounting hardware and easy-to-follow instructions allow for a hassle-free installation, saving time and effort while ensuring a secure fit. Additionally, the magnetic grille allows for a clean, unobtrusive appearance, enabling the IW Six/S to blend seamlessly with any room's decor.

The IW Six/S utilizes advanced technology to enhance audio performance. With a frequency response ranging from 40Hz to 20kHz, it captures a wide spectrum of audio, providing rich and dynamic sound. Its impedance is rated at 8 ohms, ensuring compatibility with a wide range of amplifiers and receivers. This capability allows users to integrate the IW Six/S into both multi-room audio systems and traditional home theater setups.

In terms of versatility, the AudioSource IW Six/S is ideal for various applications, whether as part of a surround sound system, for background music in a living space, or for a dedicated listening room. Its discreet design and exceptional sound quality make it an appealing option for anyone looking to enhance their audio experience without the clutter of traditional speakers.

With world-class engineering and quality components, the AudioSource IW Six/S stands out in the competitive landscape of in-wall speakers. It is an excellent choice for anyone seeking high performance, aesthetic flexibility, and ease of integration into their home audio system. Whether you’re a casual listener or a dedicated audiophile, the IW Six/S promises to deliver an audio experience that truly exceeds expectations.