Dell 1100/B110 Option Settings, Changing Boot Sequence for the Current Boot, Power Management

Page 23

Parallel Port

I/O Address

Diskette

Interface

Identifies the address for the parallel port.

Identifies and defines the floppy drive interface. You can set the interface to Auto, Read Only, or Off.

Primary Video

This setting specifies which video controller is primary when two video controllers are present on the

Controller

computer.

Onboard Video

Sets the amount of system memory to be reserved for the onboard video controller.

Controller

 

Power Management

Suspend Mode

The options are S1, a suspend state, where the computer is running in a low-power mode, and S3, a

standby state, where the power is reduced or turned off for most components, however, system memory

 

remains active.

AC Power

Determines what happens when AC power is restored to the computer.

Recovery

 

Low Power

When Low Power Mode is selected, remote wakeup events no longer power up from Hibernate or Off.

Mode

 

System Security

Password

Status

System

Password

Setup

Password

PXE BIS

Default

Policy

This option locks the system password field with the setup password. When the field is locked, the option to disable password security by pressing <Ctrl><Enter> when the computer starts is no longer available.

Displays the current status of the system's password security feature as Enabled or Disabled.

Displays the current status of the system's password security feature and allows a new system password to be assigned and verified.

Used to set the NIC On w/PCE feature policy to Deny, Accept, or Reset. See Network Interface Controller.

Boot Sequence

This feature allows you to change the boot sequence for devices.

Option Settings

Diskette Drive — The computer attempts to boot from the floppy drive. If the floppy disk in the drive is not bootable, if no floppy disk is in the drive, or if there is no floppy drive installed in the computer, the computer generates an error message.

Hard Drive — The computer attempts to boot from the primary hard drive. If no operating system is on the drive, the computer generates an error message.

CD Drive — The computer attempts to boot from the CD drive. If no CD is in the drive, or if the CD has no operating system, the computer generates an error message.

USB Flash Device — Insert the memory device into a USB port and restart the computer. When F12 = Boot Menu appears in the upper-right corner of the screen, press <F12>. The BIOS detects the device and adds the USB flash option to the boot menu.

NOTE: To boot to a USB device, the device must be bootable. To make sure your device is bootable, check the device documentation.

Changing Boot Sequence for the Current Boot

You can use this feature, for example, to restart your computer to a USB device such as a floppy drive, memory key, or CD- RW drive.

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Abbreviations and Acronyms Turning Off Your Computer Before You BeginGetting Started Recommended ToolsTurn off your computer Open the computer cover Back to ContentsRemoving the Computer Cover Inside View of Your Computer System Board Components Technical OverviewPower Supply DC Connector Pin Assignments Minimum Current a Maximum Current a Pin Number Signal name Wire Color DC Power Connector P1DC Power Connector P2 Pin Number Signal Name 18-AWG Wire Color DC Power Connectors P8 and P9DC Power Connector P4 DC Power Connector P6Pin Number Signal Name 22-AWG Wire Color DC Power Connector P7Computer Information Technical SpecificationsMemory Expansion Bus ConnectorsVideo AudioEnvironmental PowerControls and Lights PhysicalBack to Contents Network Lights Advanced TroubleshootingPower Lights Remove and then reinstall the memory modulesYellow LED Diagnostic LightsLight Pattern Problem Description Suggested ResolutionCode Cause Beep CodesMessage Possible Cause Corrective Action System setup programEnter the system setup program, verify System MessagesFDD Overview System SetupEntering System Setup System Setup ScreensHard-Disk Drive Sequence System Setup OptionsDrive Configuration SystemIntegrated Devices Boot SequenceMemory Information CPU InformationPower Management Boot SequenceOption Settings Changing Boot Sequence for the Current BootEnter system setup Clearing Forgotten PasswordsChanging Boot Sequence for Future Boots Replace the computer cover Memory Removing and Installing PartsMemory Installation Guidelines Hard Drive Power Supply Floppy Drive BatteryShut down the computer through the Start menu Installing MemoryReplace the computer cover PCI Cards CardsBefore installing any cards Removing the Front Panel Front PanelRemove the computer cover Removing the Front-Panel InsertReattaching the Front Panel Hard Drive General Installation GuidelinesConnecting Drive Cables DrivesRemoving a Hard Drive Installing a Hard Drive Page Removing a Floppy Drive Floppy DriveInstalling a Floppy Drive Removing a CD/DVD Drive CD/DVD DriveInstalling a CD/DVD Drive Adding a Second CD or DVD Drive Page Removing the Processor ProcessorInstalling the Processor Page Removing the Fan Assembly Fan AssemblyReplacing the Fan Assembly Removing the System Board Remove the microprocessor heat sink Remove the fan assemblySystem Board Reinstall the fan assembly Installing the System BoardReplacing the Power Supply Power SupplyRemoving the Power Supply Battery Replace the computer cover Replacing the Computer Cover
Related manuals
Manual 116 pages 9.03 Kb

1100/B110 specifications

The Dell 1100/B110 is a compact and efficient multifunction printer that is well-known for its reliability and value. Designed primarily for home and small office environments, the B110 is tailored to deliver high-quality printing, scanning, copying, and faxing capabilities in a single device, thus maximizing productivity and minimizing the need for multiple machines.

One of the standout features of the Dell B110 is its fast printing speed. With the ability to produce up to 27 pages per minute in monochrome, this printer is designed to handle day-to-day printing tasks with ease. The 1200 x 1200 dpi resolution ensures that documents come out crisp and clear, making it an excellent choice for professional presentations or detailed reports.

The printer utilizes a reliable inkjet technology that allows it to produce vibrant color prints alongside sharp black-and-white copies. The B110 is compatible with various paper sizes, accommodating everything from standard letter paper to envelopes and labels, enhancing versatility in printing tasks.

Another notable characteristic of the Dell 1100/B110 is its energy efficiency. This printer is designed with low power consumption in mind, helping to reduce overall operational costs. Additionally, it comes equipped with an automatic duplexing feature, enabling double-sided printing that conserves paper and further decreases environmental impact.

In terms of connectivity, the B110 offers USB 2.0 options, allowing for straightforward setup and integration into most home and office environments. While it may not have advanced wireless capabilities like some modern printers, its connectivity options are reliable and straightforward for users seeking simplicity.

For ease of operation, the Dell B110 includes a user-friendly interface with a straightforward control panel. This design allows for quick access to essential functions, ensuring that even users who are not particularly tech-savvy can navigate it with ease.

Finally, Dell has provided various software utilities that enhance the overall experience with the B110. These include driver support and additional management tools that help users maintain their printer performance over time.

In conclusion, the Dell 1100/B110 remains a solid choice for users seeking a dependable, all-in-one solution for their printing needs. With its combination of speed, quality output, and energy efficiency, it meets the demands of both home users and small businesses effectively.
Top Page Image Contents