Connecting Your System

Instruction Manual

Surround Effects and Speaker Locations

All Atlantic Technology speakers are“voiced” to the same standards of tonal neutrality and sonic accuracy.We design all of our speakers to transmit the program material into the listening environment as precisely as possible. Therefore,any of our surround speakers,such as our model 2200SR Bipole/ Dipole surround speakers, would be an excellent match for an FS-3200- based home theater system. Begin with the side speakers set to “Dipole,” then experiment with the Bipole/Dipole switch to obtain the most pleasing and realistic effect in your listening room.

See your Atlantic dealer or visit our website (www.atlantictechnology.com) for more information.

The best location for surround speakers is straight out to the sides, or slightly behind the primary listening area, approximately 1-2 feet (.3-.6m) above seated ear level,but no closer than 2 feet (.6m) from the ceiling.(See ﬁgure 6.) The surround speakers are primarily intended to re-create the ambient sounds taking place in the movie scene. Therefore, throughout most of a movie or TV program you may not be consciously aware of output from these speakers. In other words, don’t worry if you aren’t hearing the surround speakers.Please try to avoid the trap of turning the surrounds up and up so that you hear them most of the time. The result will be a much less believable surround experience.

6.1 and 7.1 Channel Systems

For best performance in a 7.1 channel system, we recommend using another pair of 920, 1200 or 2200 LR's on the back wall, and 2200 SR's on the side walls.

If you are setting up a system that uses back surround speaker(s) as well as side surrounds (Dolby Digital EX, DTS ES, etc.) you can choose to use either SR model speakers in Dipole or Bipole mode or another pair of front LR speakers in the back of the room. If the 2200 SR’s are used as back sur- rounds in a 6.1 or 7.1 channel system, they should be installed with the Right speaker placed over the listener's left shoulder and the Left speaker placed over the listener's right shoulder. About one-third of the way out from the corners in most rooms is a good starting point.

If you are using a THX Ultra 2 certiﬁed controller/receiver,you should place the back surround speakers approximately 1 to 2 feet (.3-.6m) apart in the center of the back wall. The special circuitry in the processor will help to create a believable and effective surround ﬁeld using this placement.Please read the electronics manual to learn more about this placement option.

We recommend that you connect your system using high quality dual conductor stranded wire of 16 gauge or heavier, for lengths up to 25 feet (8m) . Remember, the lower the gauge number, the heavier the wire. Use heavier gauge wire for longer runs. Please contact your audio/video dealer or installer for speciﬁc cable recommendations and further information regarding special circumstances.The terminals themselves are designed to allow the use of very heavy speaker wire or connectors. Be sure to tighten them securely, but don’t over-tighten them.

WARNING: To prevent risk of electrical shock or damage to your equipment, always switch off the ampliﬁer or receiver when making any system connections.

You can connect your speakers by using a variety of audio connectors such as banana plugs, pin connectors, spade lugs, etc., or you can:

1.Remove ½” (13mm) of insulation from each wire end.

2.Twist the stranded wire together, keeping the two ends separate.

3.Place the appropriate wire through the postholes in the connectors. These holes are revealed when you loosen the connector’s capscrew.

4.Tighten down the capscrew tightly, but be careful not to over tighten it.

5.Check the tightness of the capscrews 24 hours after hookup and occasionally after that, as they can loosen over time.

We recommend that you check your local electrical codes to make sure that you are not using improper connectors. It’s important to observe polarity while making speaker connections: red (+) terminals on the ampliﬁer to red

(+)on the speaker, black (–) on the ampliﬁer to black (–) on the speaker. Look carefully at the wires you are using and note that one of the conductors of each pair will typically be identiﬁed by color,printing on the outer jacket, ridges on the outer jacket,or a thread intertwined with the wire strands.By convention,the marked wire is connected to the red (+) terminal.Whether you are connecting a complete system, or adding a single speaker compo- nent to your present system, the wiring should look like the system wiring diagrams on the opposite page

WARNING: Before turning on the ampliﬁer, be certain that no stray wire strands are touching across any terminals as this might damage your ampliﬁer.

Finally, check the polarity of your front speakers by listening to some ste- reo music with good bass content. If the sound seems “hollow”, unusually spread out,or seem to have weak bass,recheck your connections for proper polarity and correct any out of phase connections by reversing the connec- tions to one speaker only, if necessary.

FS-3200 Manual.indd 7

10/6/04 11:00:12 AM

FS-3200 specifications

The Atlantic Technology FS-3200 is a remarkable floor-standing speaker that exemplifies the brand’s commitment to high-quality audio performance. Designed for audiophiles and home theater enthusiasts alike, this speaker blends advanced engineering with sophisticated aesthetics. The FS-3200 is engineered to deliver an immersive listening experience, making it an apt choice for both music and film playback.

One of the standout features of the FS-3200 is its innovative driver configuration. The speaker is equipped with dual 6.5-inch woven composite woofers that provide deep, powerful bass response while maintaining clarity. These woofers are designed to minimize distortion, ensuring that the sound remains true to the original recording. Complementing the woofers is a 1-inch soft dome tweeter that excels in reproducing high frequencies, resulting in an expansive soundstage that envelops listeners in rich detail.

Another defining characteristic of the FS-3200 is its high-quality cabinet construction. The speaker features a robust enclosure designed to reduce unwanted resonance and vibration, a common enemy of clear sound. The cabinet is meticulously crafted from MDF with a premium finish, not only enhancing its durability but also ensuring it fits seamlessly into any home environment.

The FS-3200 also incorporates advanced technologies that enhance its audio performance. One notable feature is its sophisticated crossover network, meticulously designed to manage the frequency distribution between the woofers and tweeter. This technology ensures that every element of the audio spectrum is reproduced accurately, providing a balanced and coherent sound experience.

For added versatility, the FS-3200 is compatible with various home theater setups. Whether used as part of a stereo system or integrated into a multi-channel surround sound configuration, it adapts effortlessly to different audio environments. The speakers are incredibly efficient, allowing them to work well with a range of amplifiers and receivers, ensuring that listeners can achieve an optimal listening experience without requiring excessive power.

In conclusion, the Atlantic Technology FS-3200 is a stellar choice for anyone seeking premium audio performance from a floor-standing speaker. With its exceptional driver technology, sturdy cabinet design, and advanced crossover network, it delivers rich, immersive sound that enhances music and film alike. For those looking to elevate their home audio experience, the FS-3200 stands out as a reliable and high-fidelity option.