Atlas ATM1700 Connect Power to the Monitor, Power Connections, Apply Power to the Monitor & PC

Page 3

5.Connect Power to the Monitor

Power source needs to be 100 - 240 VAC, 50/60 Hz, ￿30 Watts.

See connection diagram below.

Secure power connector screws to monitor.

Power should not be applied until all cables are attached and the monitor is ready to operate.

Power Connections:

TOP VIEW

100 VAC - 240 VAC INPUT (1.0 Amps Min)

1

2

PIN No.

Definition

3

AC Line Input

 

 

1

 

 

2

AC Neutral Return

 

 

3

Protective Earth Ground

WARNING: Damage can occur if power is not properly connected.

6. Apply Power to the Monitor & PC

• Press the DISPLAY POWER button on the rear of the monitor to wake the monitor up. Pressing the DISPLAY POWER button again turns off the backlight inverter and puts the monitor in a reduced power state but the touch screen remains active. It is important to note that this switch does not disconnect power from the monitor. Power is always supplied to the internal AC/DC power supply, which in turn continually supplies power to the internal monitor electronics and the optional touch screen

 

controller.

 

7. Install the Appropriate Touch Screen Driver

 

• Applies to ATM1700T touch screen version only.

 

• Insert the Documentation and Driver CD into the host PC’s CD drive.

 

• If the CD does not start automatically with the window shown below

5

displayed, then go to Start > Run, browse to the CD’s “atlas.exe” file,

0

open it, and click OK.

4

• From the Atlas screen, the user can view the Hardware User’s Guide for

- 0

the monitor being used, and/or install the touch screen drivers for the

3

particular PC operating system being used. Before installing the drivers,

6 3

please read the Touch Screen Driver Documentation for operating

-

system details.

0 0

• Reboot the PC and restart the monitor to activate the driver.

1 - 8

 

8.Verify Video and Touch Screen Functionality

Verify the monitor’s video display by running a familiar program.

If using the touch screen model (ATM1700T), use the touch screen to navigate by running a familiar program.

9.Adjust the Monitor OSD Settings as Required

Press the Select (Auto Adj) control button on the rear of the panel to initiate an automatic configuration of the screen.

Although normally not needed, the control buttons on the rear of panel can be used to make other adjustments to the screen.

Consult the Hardware User’s Guide, ATM-17-USER, on the supplied Documentation and Drive CD for detailed usage of the OSD settings.

10.Installation Complete

ADC P.N. ATM-AC-CON or

PHOENIX CONTACT P.N. 1777992

Plug Retention Screws

FRONT VIEW

 

Power

L N

PE

Connection

 

Label

LCD Power Button:

Power

 

Indicator

w w

Display Power

Button

w

DISPLAY POWER

. a u t

WARNING

o m a t i

o

Touch Screen is still

active while display

n

power is off

d i r e c

WARNING: The monitor does not automatically select a video input

t .

mode. The user must press the “UP (VGA/DVI)” button on the rear

of the monitor to select either VGA or DVI input. If a “No Video”

c

message appears on the screen, it is also suggested the user try using

o

m

the “UP (VGA/DVI)” button to select the active video input.

 

NOTE: ONCE YOU HAVE CONNECTED YOUR PC AND THE MONITOR, SELECTED THE VIDEO SOURCE, AND POWERED BOTH UNITS, IT IS SUGGESTED THAT THE “SELECT (AUTO ADJ)” BUTTON ON THE REAR OF THE MONITOR BE PRESSED TO MAXIMIZE THE VIDEO SETTINGS.

OSD Settings Main Menu:

M A I N M E N U

B R I G H T N E S S / C O N T R A S T

R G B C O L O R

P O S I T I O N

S E T U P

E X I T

1 2 8 0 X 1 0 2 4 6 3 . 9 K H Z / 6 0 H Z

Additional Help and Support

For product support, specifications, installation, and

troubleshooting, a Hardware User’s Guide, ATM-17- USER, is included on the supplied Documentation and Driver CD, or downloadable from the Online

Documentation area of the AutomationDirect Web site.

For additional technical support and questions, call our Technical Support team @ 770-844-4200.

3

Image 3
Contents Agency Approvals Verify Contents of the BoxContents ATM1700/ATM1700T DescriptionCable Connections Install Monitor through Enclosure Door or WallCutout Dimensions Mounting Clip InstallationAdjust the Monitor OSD Settings as Required Connect Power to the MonitorPower Connections Apply Power to the Monitor & PCAccessories & Replacement Parts 3 3 0 4 0W . a u t o m a t i o n d i r e c t . c o m