AOC 919Sw-1 manual Care and Maintenance, Troubleshooting, English, Safety Tips, No power

Page 15
Care and Maintenance

English

Care and Maintenance

Care

Avoid exposing your monitor directly to sunlight or other heat source. Place your monitor away from the sun to reduce glare.

Put your monitor in a well ventilated area.

Do not place any heavy things on top of your monitor.

Make certain your monitor is installed in a clean and moisture-free area.

Keep your monitor away from magnets, motors, transformers, speakers, and TV sets.

Note

Move the LCD out of the package and take off the plastic bag and Polystyrene Foam. Pull the base from Parallel versus Panel to Vertical.

Adjust the Panel within 0 degree leaning forward and 20 degree leaning backward. You must bend harder to exceed 20 degree backward but this range is for packing the unit to a small size for storage only.

Safety Tips

If smoke, abnormal noise or odor came out from your monitor, caution you should remove the power cord immediately and call your service center. Never remove the rear cover of your monitor cabinet. The display unit inside contains high-voltage parts and may cause electric shock to human bodies. Never try to repair your monitor yourself. Always call your service center or a qualified technician to fix it.

Troubleshooting

No power

Make sure A/C power cord is securely connected to the power adapter and the power supply is firmly connected to the monitor.

Plug another electrical device into the power outlet to verify that the outlet is supplying proper voltage.

Make sure all signal cables are installed.

Power on but no screen image

Make sure the video cable supplied with the monitor is tightly secured to the video output port on back of the computer. If not, tightly secure it.

Adjust brightness.

12

Image 15
Contents 919Sw-1 English Operation InstructionsFCC Warning Content WARNINGS Safety PrecautionsInstall First SetupQuick Installation Installing & Removing the BasePreparing To Install The Optional Wall Mount Arm Not Included 1. Remove the 4 screws holding the stand to the hinge2. Remove the stand Attaching The Optional Wall Mount Arm not supplied 2. Connect Analog video cable D-Sub cable Connecting the Monitor1. Connect Power cord 3. Power-ON computer and monitorRear View of the Product Front View of the ProductUsing On Screen Display OSD Functions Main MenuV or W Short Cuts Function from the buttons Sharpness To adjust the clarity of a non-WXGA 1440x900 signal with 640 x 480 @ 67Hz Supporting Timing Modes720 x 400 @ 70Hz 640 x 480 @ 60HzPower Technical InformationTechnical Specification Displayable Resolution Pixel Dimension Tilt Active Display AreaNo power Care and MaintenanceTroubleshooting Safety TipsConnect the monitor to another computer Wrong or abnormal colorsFrançais Instructions d’UtilisationAvertissement de la FCC Contenu AVERTISSEMENTS Précautions de SécuritéPremière Installation Installation RapideInstaller et retirer la base InstallerRetirer Préparer l’installation du support mural, en option non inclus 1. Enlevez les 4 vis tenant le stand sur la charniere2. Enlevez la stand REMARQUE Fixer le support mural, en option non inclus2. Connecter le câble Analogique vidéo Câble D-Sub Connecter le moniteurExemple 1440 x 900 @ 60 Hz Résolution recommandée 1. Connectez le cordon dalimentationCONFIRMER LA SÉLECTION Vue avant du produitProduit vu de dos ACTIVER/QUITTER OSDUtiliser les fonctions daffichage décran OSD Menu principal Main MenuV ou W Fonction de raccourci par boutons Avis de Résolution Resolution Notice Lavis de résolution sert Page Support des modes minutage Panneau LCD Informations TechniqueRésolution Affichable Dimension des Pixels Inclination Spécifications TechniquesRemarque Soins et MaintienEn Cas de Problème SoinsCouleurs incorrectes ou anormales Allumé mais pas d ‘affichage à l’écranEspañol Instrucciones de operaciónFCC Advertencia Contenido ADVERTENCIAS Precauciones de SeguridadInstalar Primera ConfiguraciónRápida Instalación Instalar & Remover la Baseopcional no incluido Preparación para instalar el brazo de montaje de paredNOTA Colocación del brazo de montaje de pared opcional no incluidoEjemplo 1440 x 900 @ 60 Hz Resolución Recomendada 1. Conecte el cable de toma de corriente2. Conectar el cable de vídeo cable D-Sub 3. Encienda la computadora y después el monitorCONFIRMAR SELECCIÓN Vista Frontal del ProductoVista Trasera del Producto ACTIVAR/SALIR OSDUsar las Funciones de la Muestra En Pantalla OSD Menú principal Main MenuV o W La Función de Atajo del botónes Tamaño H. H. Size Ajusta la anchura Tiempos soportados Resolución Visualizable Dimensión de Píxel Inclinación Información TécnicaPanel LCD Administración de energía Especificaciones TécnicasNota Solución de ProblemasMantenimiento y Cuidado CuidadoConecte el monitor a otra computadora Colores extraños o anormales