|
|
| CALIBRE |
| ||
3.3.9. | BlockWrite |
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
| ||
Function specification | void BlockWrite(int SlaveWriteAddress, int MSB_WordAddress, int | |||||
Parameters are: | LSB_WordAddress,int NoBytesToSend, int NoTries ) | |||||
int SlaveAddress | ||||||
|
| This is the address to be accessed via the I2C, e.g. A0H | ||||
|
| int MSB_WordAddress, int LSB_WordAddress | ||||
|
| This is the location within the slave for the data. The use of two bytes allows | ||||
|
| users to communicate with devices requiring two byte pointers e.g. 24C64 | ||||
|
| EEPROMS. If one (or both) of the word addresses are not required set the | ||||
|
| value to a number greater than 255 and it will not be transmitted. | ||||
|
| int NoBytesToSend | ||||
|
| The number of bytes to be sent which MUST be pre loaded into the driver | ||||
|
| buffers. The maximum size of this buffer is 2048 exceeding this WILL cause | ||||
|
| the data to be corrupted. | ||||
|
| Int NoTries | ||||
|
| This is the number of times the Adapter is to try to send the address. | ||||
Parameters returned | None. | |||||
Prerequisites | Adapter must be configured using Setup. The data MUST be loaded into the | |||||
|
| driver buffers PRIOR to calling this functions (see SetBlockData). | ||||
Functional description | This function causes the Adapter to send a block of data via the I2C bus. | |||||
3.3.10.SetBlockData
Function specification | int SetBlockData(int DataVal) |
Parameters are: | Int DataVal |
Parameters returned | Returns an unused integer. |
Prerequisites | Adapter must be configured using setup. |
Functional description | This stores data in the driver buffers read to be sent by the BlockWrite function. |
| MAXIMUM DATA SIZE 2048 bytes. |
3.3.11.BlockWriteStatus
Function specification | int BlockWriteStatus (void)) |
|
|
| ||
Parameters are: | None |
|
|
|
|
|
Parameters returned | int TransferStatus. |
|
|
|
| |
| Returns 0 if the transfer has not been completed. |
|
| |||
| Returns the I2C Bus status if the transfer is completed. |
| ||||
| Returns 9009H if the transfer time out. |
|
|
| ||
Prerequisites | Adapter must be configured using Setup. Data must have been sent using the | |||||
| BlockWrite function. |
|
|
|
| |
Functional description | Returns the current status of the BlockWrite transfer NOTE this function will |
| ||||
| time out if the block is not sent in NoBytes / 100 seconds (or 1 second which |
| ||||
3.3.12. BlockRead | ever is the greater). |
|
|
|
| |
|
|
|
|
|
| |
Function specification | void | BlockRead(int | SlaveAddress, | int | MSB_WordAddress, | int |
Parameters are: | LSB_WordAddress, int NoBytesToRead, int NoTries ) |
| ||||
int SlaveAddress |
|
|
|
| ||
| This is the address to be accessed via the I2C, e.g. A0H If the SlaveAddress is | |||||
| is a read address then the Word Addresses WILL NOT be sent. |
| ||||
| int MSB_WordAddress, int LSB_WordAddress |
|
| |||
| This is the location within the slave for the data. The use of two bytes allows | |||||
| users to communicate with devices requiring two byte pointers e.g. 24C64 | |||||
| EEPROMS. If one (or both) of the word addresses are not required set the | |||||
| value to a number greater than 255 and it will not be transmitted. |
| ||||
| int NoBytesToRead |
|
|
|
| |
| The number of bytes to be sent which MUST be pre loaded into the driver | |||||
| buffers. The maximum size of this buffer is 2048 exceeding this WILL cause | |||||
| the data to be corrupted. |
|
|
|
| |
| Int NoTries |
|
|
|
| |
Issue 1.0 |
|
|
|
| Page 10 |
|
01/07/03 |
|
|
|
|
|
|