Matsushita CF-T5LWETZ1 2 Removing the LCD Knob and the Speaker, Removing the Main Board

Page 26

9.2.6.Removing the LCD Knob and the Speaker

Preparation : perform the section 9.2.1., 9.2.2. and 9.2.4. first.

1.Remove the latch spring from the top case.

2.Remove the hook of the LCD knob from stopper rib of the top case.

3.Peel off the4.Peel off the tape on the speaker and speaker ring and then remove the speaker.

9.2.8. Removing the Main Board

Preparation : perform the section 9.2.1., 9.2.2. and 9.2.4. first.

1.Remove the 1 screw (I ), 1 screw (J), 2 screws (K) and 2 screws (L ).

Screw (I ) : DXQT2+E10FNL (N10)

Screw (J) : DXQT2+D4FNL (N9)

Screw (K) : DFHE5035ZB (N2)

Screw (L) : K1YE50000022 (N1003)

Speaker Box

Speaker

Speaker

Ring

Latch

Spring

LCD Knob

Location of the Spring

9.2.7. Removing the USB Board

Preparation : perform the section 9.2.1., 9.2.2. and 9.2.4. first.

1.Peel off the tapes and RJ cable sheet for clamp the USB cable.

Tape : TPD-X0033A (S1001)

RJ Cable Sheet : DFHR3C13ZA (K53)

2.Remove the connector (CN23) on the main board.

3.Remove the USB board from the bottom case.

CN23

Tape

 

Screw (K)

Screw ( I )

Screw (L)

Screw (J)

2.Remove the 2 screws (M).

Screw (M) : DXQT2+E6FNL (N12)

3.Remove the modem cable from the MDC modem.

4.Remove the side cover (L) from the bottom case.

5.Remove the DC jack holder on the DC-IN jack.

Side Cover (L)

 

Antenna Board (L)

DC Jack

Screw (N)

Holder

Screw (N)

 

Modem Cable

Tape

Main Board

LAN Cable

USB Cable

2-Port USB Board

26

Image 26
Contents CF-T5 Page Page Page Contents Page Page Names and Functions of Parts Mini Port Replicator Connector Block Diagram Diagnosis Procedure Troubleshooting Error Diagnosis by Checking Beep Signal Sound Outline of PostStuck key 02D0 System cache error Cache disabled Self Diagnosis Test Operation of PC-Diagnostic Utility Selection of tested device PC-Diagnostic utility End methodContent of the setup is returned to the setting of the user Test Item and Division of trouble GPS Wiring Connection Diagram MAIN, SUB HDDMDC Modem Preparation Removing the KeyboardHDD FFC Removing the HDDRemoving the Top Case Removing the Touch Pad PAD FFCRemoving the USB Board Removing the LCD Knob and the SpeakerRemoving the Main Board LAN Removing the Wireless LAN ModuleRemoving the Antenna Board L,R and the DC-IN Cable DC-INRemoving the LCD Unit Removing the ModemRemoving the Card Bus Ejector Removing the Inverter Removing the Hinge CoverRemoving the LCD Unit and the LCD Rear Removing the Wwan Antenna Board MAIN, SUB Removing the Wwan Board / LCD Hook WANPutting Front TP Cushion Assembly knowhow of the LCDAssembly of the LCD Front Putting TP Flexible Protection Tape Putting LCD Side DumpersLCD Front Assembly of the LCD UnitAssembly of the LCD Dumper Case Connecting LCD CableLCD Damper a Assembly of the Inverter and Putting Inverter Tapes Line processing LCD cable Putting PET Tape TP TapeHinge L Safety work Putting Tape of LCD CableAssembly of the Pen Holde Pressurizing time with LCD Rear Cushion LCD Rear WAN Assembly of the WM CablePutting LCD Rear Cushions WM CablePET Tape Assembly of the Wwan BoardPutting Tapes for WM Cable Assembly of the Wwan Antenna Board MAIN, SUB Simm Cover WAN Antenna Cover Spacer CU Assembly of the Hinge Cover L, RPanasonic Label Antenna Cover LCD RearPutting Productive Film Putting tapes for Memory Sheet of top side Assembly knowhow of the Main BoardAssembly of the MDC Modem MDC PlatePutting PET tapes DXQT2+G6FKL Assembly of the Pcmcia EjectorAssembly of the LAN Cable Safety work Line processing LAN cableLAN Assembly of the W-LAN Module / Putting Memory SheetDXQT2+D25FNL ModulePutting Sheets HDD FPC Assembly of the W-LAN SheetAssembly of the HDD FPC Page Assembly of the DC-IN Cable Setting the Main BoardLine processing Speaker Cable and putting Speaker Sheet Assembly knowhow of the Top CaseAssembly of the Speaker Pcmcia Speaker BOXFFC PAD Assembly of the LCD KnobPAD MINI-PCI Assenbly of the Antenna Cover L Assembly knowhow of the Bottom CaseSetting Antenna Board and Line processing DXQT2+E6FNLLine processing LAN Cable / USB Cable / Modem Cable DFHE5025XALine processing LCD Cable bottom case side Assembly knowhow of the BodySetting LCD LCD UnitLine processing Relay Cable Assembly of the Top Case Putting Line Hold Sheet WwanAssembly of the Keyboard Bend of two sided tape putting and KB FPCSetting Dimm Cover Assembly of the Heat Spreader and Side Cover RSetting Keyboard Tightening screw of Bottom Case Case Setting Knobs Putting RJ Cover and LabelsAssembly of the HDD / HDD Cover Screw DXQT2+E12FNLPutting HDD Cover Heat Sheet and Bottom Heat Sheet Screw DXQT26+D8FCLScrew DFHE5025XA Assembly of the LCD RearPutting Tapes for Wwan Antenna Cable Assembly of the Wwan Module Exploded View LCD Unit Ass’y / Pen Holder Section Cabinet Section Bottom Section Replacement Parts List Packing Material Antenna COVER-L DFHR3E92ZA Line Hold Sheet a Replacement Parts List EEFCX0D221RPage Page Page Page EEFCX0J101R EEFSX0D331EREEFUD0J151ER Page EEFCD0D101ER ConnectorEEFCX0G151R ThermistorShotkey Barrier Diode LEDZener Diode ThyristorIC, Q-SWITCH IC, Temperature Censor ICIC, USB Power SW IC, Power Management SwitchINDUCTOR, EMI Filter Switch B1GDCFNN0031 Transistor B1GBCFJN0037INDUCTOR, Filter DDAZS100MT3T InductorFET Transistor B1GBCFNN0042B1GFCFEN0003 Transistor B1GBCFNL0017 FET ERJ2GEJ102X RESISTOR, 1/16W, 1KΩERJ2RKF1001X RESISTOR, 1/16W, 1KΩ ERJ2GEJ510XERJ2GEJ101X ERJ2RKF2001X RESISTOR, 1/16W, 2KΩ ERJ2RKF51R0XERJ2RKF1000X ERJ2GEJ562XERJ2RKF2210X ERJ2RKF2000XERJ2GEJ201X ERJ2GEJ100XERJ2GE0R00X RESISTOR, 1/16W, 0Ω ERJ2GEJ104X ERJ2GEJ330X ERJ3GEYJ1R0V RESISTOR, 1/16W, 1ΩERJ2GEJ472X ERJ2GEJ473X RESISTOR, 1/16W, 47KΩERJ3GEYJ121V ERJ2GEJ470XERJ2RKF22R6X ERJ2GEJ334XERJ1TYJ331U RESISTOR, 1W, 330Ω ERJ2RHD104XERJ2RKD154X ERJ3GEYJ3R3VSlide Switch EVQPLDA15 SwitchSlide Switch USB ConnectorERJ2GEJ822X IC, Touchpanel ControllerERJ2GEJ102X RESISTOR, 1/16W, 1KΩ DEARA8AJ473M Resistor ArrayIC, DC/DC Converter MINI-PCI-EXP ConnectorDIP Switch B1GBCFNN0042 Transistor

CF-T5LWETZ1 2 specifications

The Matsushita CF-T5LWETZ1 is a robust and versatile device that caters specifically to the needs of professional users who require a reliable and efficient tool for daily tasks. Known for its superior durability, the CF-T5LWETZ1 model exemplifies Matsushita’s commitment to high-quality engineering and innovative technology.

One of the main features of the CF-T5LWETZ1 is its lightweight design, making it highly portable without compromising on performance. This model is equipped with a full-sized keyboard and a vibrant touchscreen display that enhances usability, allowing for smooth navigation through various applications. With an intuitive user interface, users can easily switch between tasks, boosting productivity in both office and field environments.

The CF-T5LWETZ1 incorporates advanced connectivity options, including multiple USB ports, HDMI output, and various wireless technologies like Bluetooth and Wi-Fi. This allows seamless integration with other devices and networks, catering to the needs of users who require constant connectivity, whether in a fixed location or on the go. The device also boasts an extended battery life, ensuring that users can work for hours without needing to recharge.

In terms of processing power, the CF-T5LWETZ1 features a powerful Intel processor that provides fast performance for demanding applications. Coupled with ample RAM, users can run multiple programs smoothly, making it ideal for data-heavy tasks such as spreadsheets and presentations. The device also supports a range of operating systems, enhancing compatibility for different user environments.

Matsushita has included rugged features in the CF-T5LWETZ1 to ensure it can withstand the rigors of everyday use. With a reinforced chassis and spill-resistant keyboard, this model is designed to endure accidental drops and liquid spills—a significant advantage for professionals working in challenging conditions.

Overall, the Matsushita CF-T5LWETZ1 stands out for its combination of portability, durability, and advanced technology. Its features make it a highly sought-after device for professionals requiring both flexibility and reliability. Whether used for fieldwork, presentations, or in an office environment, the CF-T5LWETZ1 is engineered to meet the demanding needs of today’s workforce, providing a trustworthy solution for various professional applications.