Velodyne Acoustics VX-11 user manual Sta l l a t i o n, Placement, Inputs

Page 5

Placement

Subwoofers operate at extremely low frequencies that are primarily omni-directional. Keep in mind that frequency response and output level can be drastically influenced by placement, depending on the acoustic properties of the listening room. Typically, the optimum location for a subwoofer is tucked away in a corner of your listening room where the greatest output levels and optimum low frequency extension can be found. The worst location for a subwoofer is far away from any walls and close to the center of your room. Avoid these locations when possible. Depending on the room size and type of furnishings in the room, perfect placement may not be possible. Finding the best location for your environment will likely require some experimentation. We suggest you experiment with the location during setup to find what sounds best to you when seated in your typical listening position.

Caution! This subwoofer has electronics built into the cabinet. Do not place the cabinet next to sources of heat such as furnace registers, radiators, etc., or near sources of excessive moisture such as evaporative coolers, humidifiers, etc. The power cord should be routed in such a way that it will not be walked on, pinched, or compressed in any way that could result in damaging the insulation or wire.

Regardless of where you install your VX-11 subwoofer, it must remain in an upright position (woofer facing forward). Using, shipping, or otherwise storing the subwoofer in any other position for an extended period of time may result in damage to the unit not covered by warranty.

I n sta l l a t i o n

Inputs

Your new subwoofer is equipped with speaker-level and line-level inputs. Use the LINE LEVEL jacks when connecting your subwoofer to a pre-amp, signal processor, integrated receiver, line-level crossover, or receiver with pre-amp level outputs. These devices will often have a Low Frequency Effects (LFE) jack which is dedicated for subwoofer use. When using the line level jacks, some receivers may not provide enough signal to have the unit’s auto-on feature operate properly. Additionally, this lack of signal may also cause the subwoofer to produce less output than it is capable of.

To alleviate this condition, we recommend the following steps:

1) If using line level jacks, BOTH THE LEFT AND RIGHT INPUT SHOULD ALWAYS BE USED

– never use just the left or just the right input. If the subwoofer’s input comes from the LFE channel of your receiver, use a “Y” splitter to divide the single input into two inputs for the Left and Right subwoofer inputs. This dual male-to-female “Y” splitter can be found at your local electronics store. If using line level connections from a preamp or signal processor, use both Left and Right inputs from your preprocessor or preamp and connect them to the Left and Right inputs on your subwoofer.

2)

If using a receiver with LFE out, be sure the LFE channel is sending adequate signal to

 

the subwoofer. We recommend setting the subwoofer’s level to the 9 o’clock position

 

(the 1/4 volume setting) and then adjust the LFE channel on your receiver or processor

 

to achieve the desired bass output. See your receiver or processor’s owner’s manual for

 

more information.

 

 

.w w w . v e l o d y n e . c o m

VX-11 User’s Manual

2

Page 4 Page 6
Image 5
Page 4 Page 6
Contents VX-11 VX-11 User’s Manual Table of Contents Pr epar e for Installation Prior to InstallationN g r a t u l a t i o n s Pr oduct Featur esInputs PlacementSta l l a t i o n Low pass Cr ossover 50 to 200 Hz Volume Contr olPhase Adjustment 0/180 Rear panel inputs, output and control layout Auto Tur n on FunctionC e i v e r / P r ocessor Subwoofer Outputs Ro s s ove rsCare of Your Subwoofer Interconnect CablesAmplifier Front Right Speaker Protection Circuitry Troubleshooting and ServiceModel Specification sVelodyne Products 115Register. . . on Line . . . It’s faster . . . and easier Velodyne Acoustics, Inc
Related manuals
Manual 16 pages 26.49 Kb

VX-11 specifications

Velodyne Acoustics has long been a prominent name in the world of audio technology, and their VX-11 model continues this legacy by offering an exceptional listening experience that caters to both audiophiles and casual listeners. The VX-11 is a high-performance speaker that combines innovative design, advanced technology, and user-friendly features, making it an ideal choice for anyone looking to enhance their sound system.

One of the standout features of the VX-11 is its incorporation of Velodyne’s signature subwoofer technology, providing deep, accurate bass response that complements its overall audio performance. The speaker's frequency response spans an impressive range, allowing it to reproduce both the subtle nuances in high notes and the powerful rumble of low frequencies. This capability ensures that listeners can enjoy their music, movies, or games with depth and clarity.

The VX-11 is equipped with a state-of-the-art amplifier that delivers substantial power while maintaining low distortion levels. This allows the speaker to produce loud sound without compromising on quality, making it suitable for varied environments, from intimate home theaters to larger gathering spaces. Additionally, the speaker features a robust enclosure design that minimizes unwanted vibrations, further enhancing audio fidelity and providing a cleaner, more immersive listening experience.

In terms of connectivity, the VX-11 boasts multiple input options, including both wired and wireless capabilities. This flexibility allows users to connect to a variety of devices seamlessly, whether they are streaming music from a smartphone, playing games on a console, or watching movies on a home theater system. The inclusion of Bluetooth functionality ensures that users can enjoy their favorite audio content without the hassle of tangled wires.

Furthermore, the design of the VX-11 is aesthetically pleasing, featuring a sleek and modern look that can easily blend into any decor. The speaker is available in multiple finishes, allowing users to choose an option that best suits their personal style.

In conclusion, the Velodyne Acoustics VX-11 is a remarkable speaker that combines cutting-edge technology with outstanding performance. With features like superior bass response, low distortion amplification, versatile connectivity options, and an elegant design, the VX-11 stands as a testament to Velodyne's commitment to delivering high-quality audio solutions. Whether you are an audiophile or simply someone who appreciates great sound, the VX-11 is sure to enhance your audio experience, bringing your favorite media to life like never before.
Top Page Image Contents