Installing and connecting the loudspeakers

Installing and connecting the loudspeakers.

When choosing a suitable location for the monitors, bear in mind that the physical mounting of loudspeakers can have a large influence on performance. For best results the monitors should be mounted on a rigid structure, supported on four pads making contacts with the laminated panel. The use of soft pads (rubber, Sorbothane, etc..) is recommended.

When used in the landscape orientation, we recommend location of the monitors so that the drive units are toed inwards, with their axes oriented towards the listening position. The distance between the two speakers should be about 1.5 to 2 metres, depending on the monitoring position. The distance between the monitoring position and each speaker should be slightly greater than the distance between the speakers. If the speakers are placed too close to each other the full stereo image may not develop, on the other hand if you place them too far apart you will notice an audible hole in the middle of the stereo image.

Ensure that the console position does not obscure the direct sound radiation from the Dual Concentric drive unit when sitting down. The engineer and producer should have a clear, uninterrupted view of the monitor loudspeakers.

Connection to the amplifier is made by means of a pair of banana sockets, located on the termination panel at the back of the speakers. When connecting the speakers it is essential that consistent polarity is observed. The red terminal on the loudspeaker must be connected to the red or positive terminal on the power amplifier, and the black terminal on the loudspeaker must be connected to the black, negative or ground terminal of the power amplifier.

The types of cable used to connect the speakers to the power amplifier will marginally affect the sound. The cross-section area of the cable should be large enough not to affect the damping factor, and generally a cable of 2.5 mm², or greater, cross-section can be recommended.

Before connecting the amplifier and the monitors, it is advisable to ensure that there is no signal present either by turning amplifiers gain down or by setting the output faders.

Power amplifiers.

The power amplifier should be reasonably well matched in power to the power rating of the speakers. A recommended range of power can be found in the specifications (at the end of this manual). The use of a powerful amplifier (i.e. the higher figure of the specified power range) provides headroom which is useful especially for highly dynamic programme materials.

Because of the high peak power handling of the Tannoy monitors, a responsible use of even more powerful amplifiers should not represent a danger for the speakers if the amplifiers are not overdriven.

600 specifications

The Tannoy 600 loudspeakers are a remarkable addition to the realm of audio equipment, known for their rich sound quality, superior craftsmanship, and advanced technologies. Renowned for their impressive performance, these speakers have become a staple for audio professionals and enthusiasts alike, making them a sought-after choice for various listening environments.

One of the standout features of the Tannoy 600 is its innovative Dual Concentric driver design. This technology integrates the high-frequency compression driver with the low-frequency cone, ensuring that sound waves originate from a single point. This alignment enhances the cohesiveness of sound, providing a more immersive and spatial listening experience. As a result, users can enjoy a more realistic reproduction of audio, making it an ideal choice for both music production and critical listening.

Another key characteristic of the Tannoy 600 is its impressive power handling capabilities. With a robust build quality, these speakers can handle substantial wattage, allowing for a dynamic range that many other speakers cannot achieve. This durability makes them suitable for various applications, including live sound reinforcement, studio monitoring, and home audio systems.

The design of the Tannoy 600 is not only aesthetically pleasing but also functional. With a sealed cabinet design, these speakers minimize resonance and distortion, resulting in a cleaner sound. This careful attention to details in construction ensures longevity and reliability, making them an optimal choice for long-term use.

Moreover, the Tannoy 600 incorporates advanced crossover technologies. This feature ensures that different frequencies are accurately directed to the appropriate drivers, resulting in a smoother frequency response and improved clarity across the audio spectrum. Listeners can appreciate the nuanced details in their favorite tracks, from deep bass notes to sparkling highs.

In conclusion, the Tannoy 600 loudspeakers exemplify the fusion of technology, design, and performance. Their Dual Concentric driver system, robust power handling, sealed cabinet, and advanced crossover technology come together to offer an unparalleled audio experience. Whether used in a professional studio or a home listening environment, these speakers are engineered to deliver sound quality that meets the high standards of both audiophiles and professionals, proving that Tannoy continues to push the boundaries of audio excellence.