Installing and connecting the loudspeakers

Installing and connecting the loudspeakers.

When choosing a suitable location for the monitors, bear in mind that the physical mounting of loudspeakers can have a large influence on performance. For best results the monitors should be mounted on a rigid structure, supported on four pads making contacts with the laminated panel. The use of soft pads (rubber, Sorbothane, etc..) is recommended.

When used in the landscape orientation, we recommend location of the monitors so that the drive units are toed inwards, with their axes oriented towards the listening position. The distance between the two speakers should be about 1.5 to 2 metres, depending on the monitoring position. The distance between the monitoring position and each speaker should be slightly greater than the distance between the speakers. If the speakers are placed too close to each other the full stereo image may not develop, on the other hand if you place them too far apart you will notice an audible hole in the middle of the stereo image.

Ensure that the console position does not obscure the direct sound radiation from the Dual Concentric drive unit when sitting down. The engineer and producer should have a clear, uninterrupted view of the monitor loudspeakers.

Connection to the amplifier is made by means of a pair of banana sockets, located on the termination panel at the back of the speakers. When connecting the speakers it is essential that consistent polarity is observed. The red terminal on the loudspeaker must be connected to the red or positive terminal on the power amplifier, and the black terminal on the loudspeaker must be connected to the black, negative or ground terminal of the power amplifier.

The types of cable used to connect the speakers to the power amplifier will marginally affect the sound. The cross-section area of the cable should be large enough not to affect the damping factor, and generally a cable of 2.5 mm², or greater, cross-section can be recommended.

Before connecting the amplifier and the monitors, it is advisable to ensure that there is no signal present either by turning amplifiers gain down or by setting the output faders.

Power amplifiers.

The power amplifier should be reasonably well matched in power to the power rating of the speakers. A recommended range of power can be found in the specifications (at the end of this manual). The use of a powerful amplifier (i.e. the higher figure of the specified power range) provides headroom which is useful especially for highly dynamic programme materials.

Because of the high peak power handling of the Tannoy monitors, a responsible use of even more powerful amplifiers should not represent a danger for the speakers if the amplifiers are not overdriven.

800 specifications

The Tannoy 800, a remarkable loudspeaker, is part of Tannoy's prestigious line of products known for their high-quality audio reproduction. As a staple in professional audio environments, the Tannoy 800 embodies the brand's commitment to excellence, providing an exceptional listening experience for both audiophiles and industry professionals.

One of the standout features of the Tannoy 800 is its Dual Concentric driver design. This innovative technology integrates the high-frequency and low-frequency drivers into a single point source. This design minimizes phase issues and ensures coherent sound dispersion across a wide frequency range. As a result, listeners enjoy accurate audio reproduction, making the Tannoy 800 ideal for critical listening situations.

The Tannoy 800 boasts impressive frequency response, typically ranging from 50 Hz to 20 kHz. This extensive range allows for a rich bass presence while maintaining clear highs, ensuring that every detail of the audio is reproduced faithfully. The speaker's sensitivity, a crucial measurement in determining its efficiency, sits around 90 dB, making it suitable for both home and professional studio applications.

Another notable characteristic of the Tannoy 800 is its robust build quality. The cabinets are constructed from high-density MDF, which reduces resonance and enhances sound clarity. The design not only contributes to the speaker's durability but also minimizes coloration, delivering a more natural and pure sound.

The Tannoy 800 also integrates advanced acoustic engineering techniques such as a finely tuned ported enclosure. This feature enables the speaker to produce deep bass frequencies while preventing distortion. The rear-firing port design optimizes airflow, allowing for improved efficiency without sacrificing sound quality.

Connectivity options are abundant, ensuring versatility in various setups. The Tannoy 800 is equipped with bi-wire and bi-amp capabilities, giving users the flexibility to customize their audio experience further. Additionally, the speaker's compatibility with various amplification systems makes it a valuable choice for both studio and home sound systems.

In summary, the Tannoy 800 encapsulates the essence of high-fidelity audio through its Dual Concentric technology, extensive frequency range, robust build quality, and versatile connectivity options. With such features, it stands as a top choice for anyone serious about audio integrity, whether in professional studios or home listening environments. The Tannoy 800 is a testament to the brand’s dedication to quality and innovation in sound reproduction.