Tandberg Data MSE 8321 manual Installing the Isdn gateway

Page 8

Installing the ISDN gateway

IMPORTANT: Before installing the ISDN gateway into the MSE 8000, and connecting the power supply, you must read the safety information at http://www.codian.com/safety.htm

Although blades are hot-swappable parts, you must only remove one

! blade at any time. Remove the power from the MSE 8000, if you need to remove more than one blade at a time.

Before hot-swapping a blade, shut down the blade using the web

! interface. Do not shut down a blade during a software upgrade or if the blade is processing.

For information about powering the MSE 8000, refer to the Getting Started Guide that accompanied the chassis.

Install the ISDN gateway into the MSE 8000 chassis

!

!

You must install either a blade or a blanking blade in each of the ten positions in the chassis.

The Supervisor blade must be installed into slot 1 of the MSE 8000 chassis.

1Remove the blade or blanking blade from the slot into which you are going to install the ISDN gateway:

iUsing a No.1 Phillips screwdriver, loosen the screws in the retaining latches with an anti-clockwise quarter turn.

iiOpen both retaining latches on the front of the blade or blanking blade. When open, a retaining latch is at a 90° angle perpendicular to the front of the blade.

iiiSlide out the blade or blanking blade.

2Open both retaining latches on the front of the ISDN gateway. When open, a retaining latch is at a 90° angle perpendicular to the front of the blade.

3Slide the ISDN gateway into the blade slot (as shown in Figure 2) until it stops.

4Simultaneously close both retaining latches on the blade (thereby engaging the connectors at the rear of the blade) to secure in the chassis as shown in Figure 3.

4

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Codian Isdn Gateway Codian Isdn Gateway Tandberg Table of contents Port and LED location General informationAbout the Isdn gateway LED behavior FDX Installing the Isdn gateway Install the Isdn gateway into the MSE 8000 chassisInserting a blade into the chassis Connecting the Isdn gateway Your Isdn connectionStep one Connect to Ethernet Port a Step two Connect to the Isdn portsStep two Assign an IP address to the Isdn gateway Initial configurationStep one Configure Ethernet Port a settings Step one Log in to the Isdn gateway Configuring the Isdn gatewayStep two Set up the Isdn interfaces Step three Configure an H.323 gatekeeper Step four Configure the dial planAdding the Isdn gateway Configuring the MCUConfiguring endpoints Calling out by Isdn Making callsCalling in by Isdn Calls fail to complete Troubleshooting and technical support informationUsing the event log to help solve a problem Getting more help Pin outs Pin numbering for PRI portsCodian Isdn Gateway 61-0020-02

MSE 8321 specifications

Tandberg Data MSE 8321 is a high-performance storage solution designed to meet the demands of modern data management and protection. This system is engineered to provide reliable, scalable, and efficient storage capabilities for businesses of all sizes.

At the heart of the MSE 8321 are its advanced storage technologies, which enable businesses to store, manage, and retrieve data with remarkable speed and efficiency. The system supports a variety of data formats and can handle large volumes of information, making it suitable for backup and archiving needs. With its high storage capacity and low total cost of ownership, the Tandberg Data MSE 8321 represents an excellent investment for organizations looking to optimize their data storage solutions.

One of the standout features of the MSE 8321 is its modular design, which allows for easy scalability. Businesses can start with a modest configuration and incrementally add storage as their data requirements grow. This flexibility is crucial for organizations experiencing rapid data growth or those with fluctuating storage needs.

The MSE 8321 also boasts robust data protection and security features. It includes options for advanced encryption, providing end-to-end security for sensitive information. Additionally, the system supports deduplication technology, which reduces redundant data and optimizes storage utilization, leading to significant cost savings.

In terms of performance, the MSE 8321 is equipped with high-speed data transfer capabilities, ensuring that backups and restores can be completed in a timely manner. This efficiency is essential for businesses that cannot afford downtime or data loss. The system’s reliability is further enhanced by its built-in redundancy features, which help safeguard against hardware failures.

Connectivity is another advantage of the Tandberg Data MSE 8321, as it supports multiple interfaces, including USB and network-attached storage (NAS) options. This versatility allows for easy integration with existing IT infrastructure and enhances the system's usability across various environments.

Overall, the Tandberg Data MSE 8321 is a comprehensive storage solution that offers a blend of scalability, security, and performance. Its innovative technology and user-friendly design make it an ideal choice for businesses looking to streamline their data management processes while maintaining high levels of security and reliability. With an increasing emphasis on data-driven decision-making, investing in a robust storage solution like the MSE 8321 is more critical than ever.
Top Page Image Contents