Velodyne Acoustics SMS -1 user manual W . v e l o d y n e . c o m

Page 13

(10)RS-232 OUT – Use this port to communicate with a second “daisy-chained” Digital Drive SMS-1.

(11)RS-232 IN – Use this port to communicate with your computer (for software updates), a touch panel remote control, or another upstream Digital Drive SMS-1. See Appendix A for an explanation of the use of the serial port, available commands, and their formats.

(12)EQ Video Output – Used to display the video generated by the SMS-1. S-Video or composite connections are available. A composite video cable is included. NOTE: Only connect to a single video output at a time.

(13)LFE OUTPUT – These connectors send the conditioned subwoofer audio signal to up to three subwoofers.

(14)EQ OUTPUT LEFT/RIGHT – Connect the audio cable from your accessory kit to these jacks: white plug to LEFT, and red plug to RIGHT.

(15)THRU – These RCA connectors are for sharing the same signal that goes into your SMS-1 with a second “daisy-chained” SMS-1 or other device. Unaltered line-level signal comes out of the THRU jack.

(16)OUTPUT – These RCA connectors incorporate the use of an 80Hz 6 dB/octave slope high pass crossover.

(17)INPUT LFE – These RCA input jacks are for line-level connection.

(18)12V TRIGGER/SPEAKER LEVEL INPUT RIGHT/LEFT – If the 12 volt trigger mode is active, 12 volts is required across these pins for power to be activated. The speaker- level connector allows for connection with exposed speaker wire.

(19)12V DC POWER SUPPLY INPUT - Connect the power supply to this jack.

.w w w . v e l o d y n e . c o m

Digital Drive User’s Manual

7

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Digital Drive SMS-1 U t i o n At t e n t i o n Vo rs i ch t At t e n z i o n e Table of Contents N gr a t u l a t i o n s I o r to installationBefore you begin Product Features and Controls Pack age ContentsRemote Contr ol Remote Contr ol Buttons Velodyne Digital Drive remote controlDigital Drive Accessor y Kit Installation OverviewSMS 1 Contr ols and Por ts Digital Drive Front and Rear Panel Connections W . v e l o d y n e . c o m Installation Quick Start SMS 1 Cable Connections Installation Step By- StepWor d about SMS 1 outputs Wo r d About Inter connect Cables Wor d About Connecting mor e than one SMSW . v e l o d y n e . c o m Quick Setup Using Self EQ SMS 1 Setup OverviewOn Screen Setup Special note for 230V users with video pr oblemsIntroductory Screen EQ Setup screen System Settings Screen W . v e l o d y n e . c o m Onscreen Programming and Setup Step by- Step W . v e l o d y n e . c o m W . v e l o d y n e . c o m W . v e l o d y n e . c o m Screen should now look something like this About Room Placement W . v e l o d y n e . c o m W . v e l o d y n e . c o m W . v e l o d y n e . c o m W . v e l o d y n e . c o m W . v e l o d y n e . c o m W . v e l o d y n e . c o m W . v e l o d y n e . c o m W . v e l o d y n e . c o m W . v e l o d y n e . c o m W . v e l o d y n e . c o m W . v e l o d y n e . c o m Restoring Defaults Runtime Mode Volt Trigger Mode W . v e l o d y n e . c o m Software Updates Troubleshooting and ServiceAbout Room Equalization Care of Your Digital Drive SMSCom Por t Setup Appendix a RS-232 Serial Overview and CommandsDD in and OUT Por t Pin Configuration T r o d u c t i o nW . v e l o d y n e . c o m Function Code Description Appendix B Summary of Special Remote CodesDigital Drive Signature Other velodyne ProductsVelodyne Acoustics, Inc
Top Page Image Contents