Subwoofer out from A/V Processor | Velodyne Acoustics VA-1250X

output and increased noise. In these cases, to optimize your sub- woofer performance you should bypass the internal crossover in your Velodyne subwoofer.

To bypass the crossover within the subwoofer, simply locate the switch marked "normal/bypass" on the back panel of the subwoofer and set to the "bypass" position. This will eliminate the internal crossover function.

Note

If not using an external crossover, you should use the built-in crossover for optimal performance.

Subwoofer out from A/V

Processor

From the low pass output of your signal processor Install into right or left RCA line in connector in the back of the subwoofer or use a "Y" connector adapter into both right and left RCA line in connectors in the back of the subwoofer.

Speaker-level connection

Figure 2 shows an easy way to connect your VA-1250X subwoofer directly to your receiver or integrated amplifier.

When connected in this fashion, your satellite speakers will be crossed over at 80/100Hz, which removes the lower bass from your speakers thus, enabling them to do a better job reproducing high frequencies.

You may also connect your satellites directly to your receiver or amplifier along with the subwoofer if you wish to bypass the internal high-pass crossover.

Caution!

To avoid damage to your main amplifier, be sure to maintain correct polarity when making all connections. Red (positive) to red, and black (negative) to black. Be sure that all connections are tight, and that there are no loose strands or frayed wires.

continued. . .

Installation

Your new VA-1250X subwoofer system provides for a number of installation options. Read all the installation information below in order to determine which installation option is best for your system.

Remember to perform all installation procedures with system power turned off.

Inputs

Your new subwoofer is equipped with both speaker-level and line- level inputs. Use the LINE-IN jacks when connecting your sub- woofer to a pre-amp, signal processor, orsubwoofer output/LFE. The FROM AMPLIFIER jacks connect directly to the speaker outputs of a integrated amplifier or receiver. Your amplifier section will notice no additional loading effects when you use these inputs because of their high impedance.

Note

Do not use both LINE-IN and FROM AMPLIFIER inputs simulta- neously.

Volume control

This control allows you to balance the output from the subwoofer to the main speakers in your system. This control should be set to achieve similar volume level from both the main speakers and subwoofer.

Low-pass crossover

Both sets of inputs sum the left and right channels together and the resulting signal is passed through an adjustable low-pass crossover before being amplified. The crossover control allows you to adjust the upper limit of the subwoofer's frequency response from 40 to 120 Hz. The subwoofer's response will begin rolling off above the frequency you set this control to.

You should set the crossover frequency to obtain a smooth and seamless transition from the subwoofer to the main speakers in your system. If your main speakers are smaller units with limited low frequency output, you may wish to choose a higher frequency (such as 100-120Hz) than you would with larger speakers which have greater low frequency output. With larger speakers, you might start with this control set lower, such as 80Hz.

5	☞	2	☞

VA-1250X specifications

Velodyne Acoustics has long been a pioneer in the world of audio technology, and their VA-1250X model exemplifies this legacy with a blend of innovative features and impressive performance. Designed for audiophiles and casual listeners alike, the VA-1250X provides an exceptional listening experience, making it a standout choice in the modern audio market.

One of the main features of the VA-1250X is its powerful Class D amplifier. With an output of 1250 watts peak power, this amplifier ensures that the sound produced is not only loud but also maintains clarity and detail across all frequencies. The efficient design of the Class D amplifier minimizes energy consumption while maximizing output, catering to both performance and environmental consciousness.

At the heart of the VA-1250X are Velodyne’s signature Advanced Digital Signal Processing (DSP) technologies. This sophisticated DSP works to optimize the audio signals, providing a clean and distortion-free sound even at high volume levels. This means that users can enjoy their favorite music, movies, or games without worrying about losing audio fidelity, even in challenging acoustic environments.

The VA-1250X also boasts a robust driver setup that includes a high-excursion composite cone woofer. This design allows for deeper bass response, providing a rich and immersive experience that is particularly noticeable in bass-heavy genres. The enclosure is engineered to reduce resonance, further ensuring that the sound remains pure and impactful.

Another key characteristic of the VA-1250X is its adjustable crossover frequency and phase control. This capability allows users to customize the audio output to better integrate with their existing speaker systems, catering to personal preferences and specific room acoustics. With multiple input options, including RCA and XLR connections, the VA-1250X is versatile enough to connect seamlessly with a variety of audio setups.

In summary, Velodyne Acoustics’ VA-1250X combines a powerful Class D amplifier, advanced digital signal processing, and a thoughtfully designed driver system to deliver an unparalleled audio experience. Its adaptability and performance make it an excellent choice for anyone looking to elevate their home audio system, whether for casual listening or critical sound reproduction. With the VA-1250X, Velodyne continues to push the boundaries of audio technology, promising satisfaction for enthusiasts and everyday users alike.