Turbosound TA-500TDP, TA-500HDP Attenuation & Gain Setting, Output Connections, Damping Factor

Page 67

user manual

TA-500

Setting higher gain does not change the maximum available power but changes the level of signal input to achieve maximum power. In any case, provided that the input signal is less than 20dBu/7.7V, the built in limiter circuit will prevent distortion within the amplifier.

The gain should be set to match the signal from the source, e.g. mixer, controller, or equaliser.

Attenuation & Gain Setting

The front panel gain controls allow precise level settings, and may be used to adjust the relative levels of sections of a large system, for example downfills or side seating cover in an arena.

The front panel gain controls are also useful when initially checking a system after it has been connected up.

Note that in BRIDGED mode only the Channel A control is active.

Output Connections

A Speakon NL4 connector is provided on each channel.

Damping Factor

The T series amplifier outputs provide a high damping factor, typically 400 times at low audio frequencies. This damping helps the amplifier to control the loudspeaker drive units, provided that the resistance of the intervening cables and connectors is very low. The sonic benefits of high damping factor are most pronounced at bass and low-midrange frequencies (i.e. 10 to 600Hz) providing a subjectively tighter sound as a result of the improved reproduction of transients.

Amplifier damping factor is degraded by high resistance in the loudspeaker circuits; i.e. thin conductors, long output cable runs and tarnished, corroded or loose connections.

Damping factor is maximised by installing cables containing conductors of large cross- sectional area, and by specifying connectors with heavy-duty contacts and waterproof covers. The cable sets supplied with Aspect systems are manufactured to a high specification with these considerations in mind.

TA-500 user manual Page 67

Image 67

Contents Aspect TA-500 Systems TA-500 TA-500 TA-500 Audio Connections & Controls TA-500HDP EC Declaration of ConformityTurbosound Aspect System Concepts IntroductionAspect Polyhorn Concept TA-880 TA-500 Narrow 25º horizontal coverage LMS-D2X Loudspeaker Management Systems Loudspeaker Management System LMS ConceptNetwork Capability Aspect Loudspeaker Components Power AmplifiersSelf-powered Loudspeakers Digital ControllersTA-500 TA-500t Touring Three-way Loudspeaker TA-500DP Self-powered Three-way LoudspeakerTA-500tDP Self-powered Touring Three-way Loudspeaker TA-500 Three-way LoudspeakerTSW-218 Subwoofer TA-500HDP Self-powered Horizontal Three-way LoudspeakerTA-500H Horizontal Three-way Loudspeaker TA-500HM Two-way High/Mid LoudspeakerB18 Subwoofer B18DP Self-powered SubwooferTransportation Overview Flying and StackingSafety Notes on Rigging Secondary Safeties Safety InspectionsTA-500 Sample Certificate of Load Test Vertical Coverage Flying HardwareAspect TA-500 Flying Systems Horizontal CoverageTA-500T Touring Flying System Flybar SettingsTouring two-wide flybar TOP View FC-500T Flying Chains Flying MatrixTA-500 Integral Flying Hardware TS-890 Tilting StrapsCaptive Biscuit BoltLocking Mechanism Connecting Flying Chains to the CabinetSliding the top chain profile into the slot Assembly of the Top Chains to the CabinetAdding additional rows Connection of additional rowsAttaching the biscuit Setting the angles between rowsBiscuit slides into lower cabinet Attaching the Tilt StrapsFront view of the assembled cluster Lifting the columnTA-500 TA-500 Install Flying System Rigging Instructions TA-500 TA-500 Array is now ready to pick up Flying a single TA-500 cabinet using M10 eyebolts Unpacking Mechanical InstallationLMS Series Loudspeaker Management Systems IntroductionLMS-D24 and D26 Loudspeaker Management Systems FeaturesLCD Front Panel FunctionsTA-500 Rear Panel Functions Operating the LMS-D24 and D26 Starting up Selecting a Factory PresetCreating a Crossover Navigation and Viewing Parameters EQ1 100Hz 0dBNavigation Out1 Freq Width Gain EQ1 100Hz 1.4Q 0.0dBPreset Recall PresetsStore My System Preset StoreOutput DSP block diagram DSP Processing Layout Input DSP block diagramStereo / Mono Formats DSP processing Input Channels A Delay 1.50msA Freq Shape High and Low shelving filters Parametric EqualisationParametric filters Output Channels Gain and Polarity DelayHigh and Low Pass Filters Out1 Freq Shape LPF 2.50k LR24Out1 Freq Slope Gain EQ- 100Hz 12dB 0.0dB Routing LimitersUtilities Utility functions General Features & Facilities T-45 High Efficiency Audio Power AmplifiersFront Panel Functions T-25 Front Panel Functions T-45 Powering Up Mains PowerSafety Earthing Voltage Range Voltage SettingAudio Connections & Controls Polarity Gain and Sensitivity SettingsInput Impedance Output Connections Attenuation & Gain SettingDamping Factor Cooling System Long Speaker LinesTA-500 TA-500t TA-500H TA-500HM Appendix a Technical SpecificationsTA-500DP TA-500tDP TA-500HDP Stock Code Model Description Appendix B Spare Parts ListAppendix C Warranty TA-500

Related manuals

Manual 73 pages 47.14 Kb