Positioning, AC Mains Connection | SLS Audio PLS8695 manual

PLS8695 True Line Source Array Owner’s Manual

Page 5

3.2Positioning

The PLS8695 has a very defined vertical dispersion, which helps prevent interaction with the floor and ceiling and extends the nearfield listening area. It is important to set the speaker so the bottom of the box is approximately at chest height of the first listeners. The speaker may be tilted for proper positioning relative to the coverage area. It is highly recommended that our free LASS aiming software be used to set the position and angle of the PLS8695(s).

3.3AC Mains Connection

The AC mains power cord is connected to the front panel through the blue Neutrik Powercon. The mating cable end connector is a Neutrik NAC3FCA. The grey Powercon connector is a power outlet that allows looping to adjacent PLS8695’s. The looping outlet mating cable connector is a Neutrik NAC3FCB. Up to (2) PLS8695’s can be used on a single 20 amp circuit.

3.4Audio Connection

The PLS8695 accepts a balanced audio signal at the XLR audio input connector located on the back panel. Pin 3 is high signal. The input is transformer balanced with an input impedance of 15K Ohms. Connect an appropriate XLR cable between an audio source (mixer, processor, etc.) to the balanced input connector. Unbalanced connec- tions can be accomplished by grounding pin 2 or 3 of the XLR audio input connector through the use of an appropri- ate adapter or cable. A buffered loop output is provided for additional PLS8695s and/or active subwoofers.

3.5Power Connection

Prior to connecting the power cord and turning on the amplifier, always verify the line voltage selection switch is set for the correct AC voltage present in the region of use. The PLS8695 is designed to operate on either 115VAC or 230VAC by using the line voltage selection switch. Damage may occur to the electronics if the speaker is powered up with the line voltage selector switch in the incorrect position. Once set to the proper range, the amplifier will regulate the internal voltages so that output power does not change with supply voltage.

3.6Audio Level Control

The PLS8695 is equipped with a detented audio level control for use in setting the overall audio level. Set this control to the desired position based upon the nominal gain structure desired.

3.780Hz High Pass Filter (in - disabled; out - enabled)*

The PLS8695 is equipped with an 80Hz 2nd-order Butterworth high pass filter for use in applications having a subwoofer or for restricting the low frequencies in speech only systems. The filter may be enabled or disabled by using the 80Hz HPF switch located on the back panel.

Rev: 512

1650 W. Jackson Ozark, MO 65721 (417) 883-4549

PLS8695 specifications

The SLS Audio PLS8695 is a high-performance loudspeaker designed to deliver exceptional sound quality and clarity, making it ideal for a wide range of audio applications. This versatile speaker is especially popular in live sound, installations, and even in home theater setups. The PLS8695 is engineered for high efficiency, ensuring that it can produce a powerful sound while drawing minimal power.

One of the standout features of the PLS8695 is its dual 8-inch low-frequency woofers. These woofers are designed with lightweight cones that enable fast response times and deep bass reproduction. This allows the speaker to handle low-end frequencies with impressive accuracy, ensuring that the sound experience is immersive. Additionally, the use of a high-temperature voice coil enhances the speaker's reliability and performance, especially during extended use.

The PLS8695 also includes a 1.75-inch titanium compression driver, coupled with a custom-designed horn. This combination ensures that high-frequency sounds are delivered with precision and reduced distortion. The horn is engineered to provide even coverage across a wide dispersion pattern, allowing the audio to be enjoyed by a larger audience without hot spots or dead zones, making it ideal for large venues.

Another notable characteristic of the PLS8695 is its rugged and durable construction. The cabinet is built from high-quality materials designed to withstand the rigors of live use, while also being lightweight for easy transport and setup. The speaker features a sleek, professional finish that not only adds to its aesthetic appeal but also protects it from scratches and wear.

In terms of connectivity, the PLS8695 is designed with versatility in mind. It features professional-grade input connectors that can accommodate various audio sources, ensuring compatibility with different sound systems and setups. The speaker also has built-in mounting options, allowing for easy installation in various configurations, whether hanging from a truss or mounted on a stand.

In summary, the SLS Audio PLS8695 is a powerful and versatile loudspeaker that excels in delivering high-quality sound across a wide range of applications. With its robust design, advanced technologies, and thoughtful features, it is an excellent choice for professionals seeking reliable performance in demanding environments. Whether for live performances, permanent installations, or home audio use, the PLS8695 stands out as a premier sound solution.