Panasonic TH-65PF9UK manual Serial Terminals connection, Communication parameters, Command

Page 11

Connections

SERIAL Terminals connection

The SERIAL terminal is used when the Plasma Display is controlled by a computer.

COMPUTER

RS-232C Straight cable

SERIAL

1 2 3 4 5

6 7 8 9

Pin layout for SERIAL Terminal

D-sub 9p

Notes:

•Use the RS-232C cable to connect the computer to the Plasma Display.

•The computer shown is for example purposes only.

•Additional equipment and cables shown are not supplied with this set.

The SERIAL terminal conforms to the RS-232C interface speciﬁcation, so that the Plasma Display can be controlled by a computer which is connected to this terminal.

The computer will require software which allows the sending and receiving of control data which satisﬁes the conditions given below. Use a computer application such as programming language software. Refer to the documentation for the computer application for details.

Communication parameters

Signal level	RS-232C compliant
Synchronization method	Asynchronous
Baud rate	9600 bps
Parity	None
Character length	8 bits
Stop bit	1 bit
Flow control	-

RS-232C Conversion cable

D-sub 9-pin female		Details
	2	R X D
	3	T X D
	5	GND
4	• 6	Non use
	7	Shorted
	8	Shorted
	8
1	• 9	NC

Basic format for control data

The transmission of control data from the computer starts with a STX signal, followed by the command, the parameters, and lastly an ETX signal in that order. If there are no parameters, then the parameter signal does not need to be sent.

STX C1 C2 C3 : P1 P2 P3 P4 P5 ETX

	Colon	Parameter(s)	End
Start	3-character	(1 - 5 bytes)	(03h)
(02h)	command (3 bytes)

Notes:

•If multiple commands are transmitted, be sure to wait for the response for the ﬁrst command to come from this unit before sending the next command.

•If an incorrect command is sent by mistake, this unit will send an “ER401” command back to the computer.

Command

	Command	Parameter	Control details
	PON	None	Power ON
	POF	None	Power OFF
	AVL	**	Volume 00 - 63
	AMT	0	Audio MUTE OFF
	AMT	1	Audio MUTE ON
		1	Audio MUTE ON
	IMS	None	Input select (toggle)
		SL1	Slot1 input
		SL2	Slot2 input
		SL3	Slot3 input
		PC1	PC input
	DAM	None	Screen mode select (toggle)
		NORM	NORMAL (4 : 3)
		ZOOM	ZOOM
		FULL	FULL
		JUST	JUST
		SELF	Panasonic AUTO

With the power off, this display responds to PON command only.

11

Image 11

Contents Model No. TH-65PF9UK Número de modelo Operating Instructions Manual de instruccionesEnglish EspañolRisk of Electric Shock Do not Open Important Safety Instructions Table of Contents Trademark Credits FCC CautionCanadian Notice When using the Plasma Display Safety PrecautionsAC Power Supply Cord MaintenanceSafety Precautions / Maintenance SetupRemote Control Batteries AccessoriesAccessories Supplied Open ConnectionsAC cord ﬁxing CloseConnections Signal Names for Mini D-sub 15P ConnectorPC Input Terminals connection Basic format for control data CommandSerial Terminals connection Communication parametersDVI-D connection Component / RGB connection & RGB signal R, G, BDVI-D Input Connector Signal NameConnecting the plug to the Wall Outlet Power on / OFFConnecting the AC cord plug to the Plasma Display On OFF Basic ControlsBasic Controls On-Screen Menu Displays Advanced SettingsOn-Screen Menu Displays Power on Time Power OFF TimeINPUT1 INPUT2 INPUT3 PC Selecting the input signalInitial selections Selecting the On-Screen Menu LanguageNormal Full Aspect ControlsNormal Zoom Full From the unit Panasonic Auto JustDuring COMPONENT, RGB and PC input signal Adjusting POS. /SIZESize / DOT Clock / Clock Phase / 11 Pixel Mode Press to adjust POS. /SIZEAdjusting POS. /SIZE Picture which you would like to change input modes Normal ViewingUnder main Picture and sub picture display, select Sub screen Main screen Advanced PIPCinema Picture AdjustmentsStandard DynamicPicture Adjustments Advanced SettingsMute Sound AdjustmentSelect the magniﬁcation required for the enlarged display Digital ZoomDisplay the Operation Guide Select the area of the image to be enlargedPress to select Set Present Time SetupPress to set up Present Time of DAY Press to select Power on Function SET UP TimerDisplay the SET UP Timer Screen Press to select Power on Time / Power OFF TimeNegative / Scroll selection Mode selectionStart setting Screensaver For preventing after-imagesScreensaver For preventing after-images Setup of Screensaver TimePress to display the SET UP menu Reduces screen after-imagePress to exit from Screensaver Side BAR AdjustOFF Dark MID Bright Addition sign Selected Input Reduces power consumptionCustomizing the Input labels Press to select on or OFF SET UP for Multi DisplayHow to setup Multi Display Group of 4 2 × Group of 9 3 × Group of 16 4 ×Display Number locations for each arrangement Examples SET UP for Multi DisplayPress to select Seam Hides Video Press to select OFF, onID Cancellation Seam Hides Video SettingID Remote Control Function ID remote control button operationComponent RGB SET UP for Input SignalsComponent / RGB in Select 3D Y/C Filter For Ntsc AV imagesColor System SET UP for Input SignalsColor System / Panasonic Auto Pulldown / Video NRDisplays the H Horizontal / V Vertical frequencies Setting RGB sync signalSync FREQ. kHz / V-FREQ. HzOff-timer Options AdjustmentsLevel Options AdjustmentsMenu & Enter NormalizationShipping condition Plasma Display panel TroubleshootingDVI-D DVI-D/COMPONENT/RGB/PC input signalsTH-65PF9UK SpeciﬁcationsLimits and Exclusions Panasonic Canada Inc Customer’s RecordPanasonic Broadcast & Television Systems Company Executive Ofﬁce