SV Sound | SV Sound PB13 manual

Chapter 6-3	SV Sound

∙Also, is your subwoofer turned ―ON‖? We don’t mean ―is your sub- woofer amplifier on?‖ but rather, is your AVR sending a bass sig- nal to your sub amp? This can only happen if you say ―Yes‖ (or ―ON‖) in the ―Subwoofer‖ selection during the setup of your AVR’s setup menu.

∙Is your receiver connected to the sub amp? Use a well-shielded

―RCA‖ or XLR cable (sometimes called a ―patch cord‖) to connect the sub- woofer output of your AVR to either input jack of your subwoofer’s dedicated amp. Again, you’ll need to ―split‖ the bass signal with a ―Y Cable‖ if you have a pair of subs. But you only need feed one of the two inputs (it doesn’t matter either Right or Left) of any SVS Powered Box sub.

∙Is your Radio Shack ® sound pressure level (SPL) meter ready? This tool is absolutely essential to proper home audio setup. It’s akin to a tire pressure gauge for your car. Set the meter to ―Slow‖ and ―C-weighting‖ (and turn the dial to 70dB. If using Avia for calibration tones, set your meter to 80dB instead.

Getting ready to start now: Make sure your receiver or proc- essor’s master volume is set to ―00 dB‖ or some other easy to remember “reference level”. Then, ensure your sub’s volume/

gain control is set no more than 1/4 to 1/3rd up, for now, leaving plenty of adjust- ment ―up‖.

It’s also critical to check the subwoofer output level control of your AVR before you begin the test tones. Set the AVR’s subwoofer output to about 1/3rd up too. Turn off any sound-field processing schemes, ―Mid-night Mode‖, ―DRC‖ (dynamic range control), ―Movie Mode‖ etc. If it is an option in your system, route your LFE to the ―subwoofer only‖, not ―mains + sub‖.

Now play your AVR’s internal test noise “tones” so you have something to measure with your SPL meter. When the tones start alternating from speaker to speaker (watch your sound meter now), set each speaker’s volume to about 75 dB by using the receiver’s dedicated channel level controls (leaving your AVR’s master volume the same).

We recommend you turn down the AVR’s subwoofer channel output level before you significantly lower your subwoofer’s gain control. This helps keep distortion sent to your SVS to a minimum. Note: You should not set the AVR’s subwoofer level control much lower than the first 1/4th of the receiver’s control range. Some downward adjustment may be needed to fine tune levels later. If your subwoofer’s SPL meter reading is still too high, then turn down the sub’s amp volume a little with each run of the test noise signal, as it cycles from speaker to speaker and the subwoofer.

PB13 specifications

The SV Sound PB13 is a powerful subwoofer that has gained recognition among audiophiles and home theater enthusiasts for its impressive performance and advanced technologies. Known for its deep and accurate bass response, the PB13 is an ideal choice for those seeking to elevate their audio experience, whether for music, movies, or gaming.

One of the standout features of the PB13 is its large, high-excursion 13.5-inch driver, designed to deliver rich low-end frequencies. This driver, combined with a high-powered 1000-watt RMS amplifier, allows the subwoofer to produce deep bass that is both loud and precise. This ensures that users are enveloped in a full soundstage, making for an immersive listening experience.

The PB13 incorporates SV Sound’s proprietary Room Gain Control technology, which helps to optimize the subwoofer's performance based on the specific acoustics of the listening environment. This feature ensures that homeowners can get the best possible bass response, regardless of the room size or shape. Additionally, it includes advanced signal processing capabilities, allowing users to fine-tune their audio settings easily.

Another notable characteristic of the PB13 is its sturdy cabinet construction. The enclosure is made from high-quality MDF, which minimizes vibrations and resonance that can distort sound quality. This is essential for maintaining clarity in bass frequencies, especially at higher volumes. The subwoofer is also designed with a front-firing port, providing versatile placement options while maintaining optimal airflow for maximum performance.

Furthermore, the PB13 offers a wide frequency response, reaching down to 18 Hz. This capability means that it can reproduce the deep bass notes often found in modern music genres and action-packed movie soundtracks. The result is a full-bodied audio experience that captivates the listener.

In terms of connectivity, the PB13 is equipped with both RCA inputs and speaker level inputs, allowing for versatile integration with various home theater systems and setups. The user-friendly controls on the rear panel facilitate easy adjustments to volume, phase, and crossover frequency, enabling users to tailor the subwoofer's output to their preferences.

Overall, the SV Sound PB13 subwoofer stands out in the crowded audio market with its advanced technology, robust construction, and impressive sound performance, making it a top choice for anyone looking to enhance their audio system. Whether for casual listening or critical listening sessions, the PB13 promises to deliver a bass experience that is both thrilling and satisfying.