SV Subwoofers

Page 8

your sub, getting these bass wave forms to arrive in a complementary, enhancing fashion is the difficult job of the phase control. Essentially, “phase” varies the tim- ing of the bass waves coming from the sub. But don’t despair if you don’t hear much difference with changes to the phase knob — the effect of bass cancellation will vary by volume and frequency in your room, and no single setting is likely to ever be “perfect”. One technique to optimize phase is to find a nice “bassy” loop (such as the menu of “Godzilla”) and measure the loop’s SPL response at various points. As the loop runs, you can have an assistant adjust the phase control. When you see the most response on a given bass passage, typically that’s the setting with the least room-induced cancellation (for the frequencies of the demo loop).

Line In/Out. Use one of the sub’s “Line In” jacks to connect the subwoofer to the output jack of your receiver/processor. Feeding just one input is enough. If you are using a conventional amp and/or a stereo setup you can use the “Line Out” jacks to send sound (filtered of deep bass information) back to your system amp. A simple RCA to RCA cable is all you need for either type configuration.

Auto On. Your sub allows an “Auto On” mode… or can be on all the time. With the switch in the “Auto” position your subwoofer will “sense” that a DVD or CD etc. has begun and switch on immediately (the “hard power switch” mentioned below must be on, naturally). A few minutes after a movie finishes, the auto-on light will turn red, switching the sub back off. When running (and sensing a signal) the auto- on LED will be green. Sometimes, with very low listening levels, your subwoofer might not get enough of a bass signal from your surround sound processor to “trip” the auto-on circuit. Should you ever find this to be the case you may leave this switch to “On”, or turn the receiver’s subwoofer output up, and the sub down.

Crossover enable switch. If you allow your DD/DTS surround-sound receiver or processor to manage bass frequencies (recommended), this switch should be set to “Disabled”. This eliminates the effects of the “Crossover Frequency” knob and allows your sub to reproduce just what it’s fed from the receiver. If you use the sub in a two channel (stereo only) configuration, then “Enable” the crossover and adjust the knob to best blend the sub into the low frequency output of your speakers.

High level inputs/outputs. Not commonly used today, but binding posts are there in case you don’t have low-level inputs/outputs on your receiver/processor. Typically utilized only if you are not using a DD/DTS compatible system.

Power. This heavy duty two-position switch next to the power cord will com- pletely cut the power to your sub amp. Flip this switch to off before you ever move the sub or change inputs or outputs.

A/C Connection. Plug your sub into a dedicated A/C outlet. “Convenience” outlets of typical receivers often don’t provide the needed current. Avoid them.

Fuse. User replaceable, contact SVS if you have trouble finding one. The fuse can be accessed by a small round door immediately next to the power cord fitting.

SVS PB2-Ultra specifications

The SV Sound SVS PB2-Ultra subwoofer is a powerhouse in the world of home audio, renowned for its exceptional performance and advanced engineering. Designed to deliver deep, impactful bass, it caters to audiophiles and home theater enthusiasts alike, establishing itself as a reference point in the realm of subwoofers.

At the heart of the PB2-Ultra is its formidable 12-inch driver, which utilizes a massive motor structure and a long-throw voice coil. This combination allows for impressive excursion capabilities, producing bass frequencies with remarkable clarity and authority. The driver is housed within a robust, ported enclosure that enhances its performance by maximizing the efficiency of airflow, resulting in deeper bass response.

One of the standout features of the SVS PB2-Ultra is its advanced dual driver design. With two active 12-inch drivers working in concert, the subwoofer is able to create an expansive soundstage and rich, immersive sound. The dual-driver configuration also helps to minimize distortion, enabling the subwoofer to reproduce intense low frequencies without losing detail.

Powering this impressive setup is a high-performance built-in amplifier that boasts a staggering output of 1200 watts RMS and 4000 watts peak. This substantial power reserve allows the PB2-Ultra to easily handle dynamic peaks, delivering a thunderous yet clean bass response, whether it's in the middle of a movie's action scene or during a music playback. The amplifier includes advanced software features for added flexibility, allowing users to fine-tune the subwoofer's performance to suit their listening environment.

Moreover, the PB2-Ultra is equipped with sophisticated tuning options. The subwoofer features adjustable phase control, variable low-pass filtering, and volume control, giving users the ability to achieve seamless integration with their main speakers. Additionally, the innovative SVS app allows for easy remote access to these settings, making it simple to adapt the subwoofer's performance on the fly.

Durability is another key characteristic of the PB2-Ultra. Constructed with high-quality materials and finishes, it not only looks elegant but is built to last. The stylish design allows it to fit seamlessly into various room decors, making it as visually appealing as it is functionally exceptional.

In summary, the SV Sound SVS PB2-Ultra is a high-quality subwoofer that combines advanced technology, powerful performance, and user-friendly features. Whether for a cinematic experience or music enjoyment, it stands at the forefront of subwoofer innovation, ensuring that listeners experience their audio in its fullest form.