Panasonic CF-F9 Troubleshooting Basic, „ Starting Up and Sleep/Standby and Hibernation Mode

Page 25

Troubleshooting (Basic)

Follow the instructions below when a problem has occurred. There is also an advanced troubleshooting guide in the “Reference Manual”. For a software problem, refer to the software’s instruction manual. If the problem persists, contact

your technical support office. You can also check the computer’s status in the PC Information Viewer (Î Reference Manual “Check the Computer’s Usage Status”).

„Starting Up and Sleep/Standby and Hibernation Mode

The computer does not

z Connect the AC adaptor.

power on/

z Insert a fully charged battery.

The power indicator or bat-

z Remove the battery pack and the AC adaptor, then connect them again.

tery indicator is not lit.

z If an additional RAM module has been inserted, remove the RAM module and check to

see if the RAM module is the recommended one.

 

 

z When the CPU temperature is high, the computer may not start up to prevent overheating of

 

the CPU. Wait until the computer cools down, and then turn the power on again. If the com-

 

puter does not power on even after cooling down, contact your technical support office.

Windows does not start up. z Remove all peripheral devices (e.g. USB memory).

zIf an additional RAM module has been inserted, remove the RAM module and check to see if the RAM module is the recommended one.

zIf the power indicator is lit, slide the power switch for four seconds or longer to turn off, then turn on again.

zUsing the following procedure, start up in Safe Mode, and check the error details.

A Turn on the computer, and when the [Panasonic] boot screen disappears (after enter- ing the password*1 if one is set) hold down F8.

B Release your finger when [Windows Advanced Options Menu] is displayed, and with

Ïor Ð, select [Safe Mode], then press Enter. Follow the on-screen instructions.

 

*1 Supervisor Password or User Password set with the Setup Utility

 

z Press F9 in the Setup Utility to return the Setup Utility settings (excluding the pass-

 

words) to the default values. Start the Setup Utility and make the settings again.

 

 

After adding or changing the

z Turn off the computer and remove the RAM module, then confirm whether the RAM

RAM module, the power is

module has compliant to specification. When the RAM module has conformed to specifi-

turned on but nothing is dis-

cation, install it again.

 

 

played on the screen.

 

 

 

 

Cannot boot from internal

z Make sure that the bootable CD/DVD is set properly.

CD/DVD drive.

z Start the Setup Utility, and confirm the following settings.

 

[Optical Drive] is set to [Enabled] in the [Advanced] menu.

 

[Optical Drive Power] is set to [On] in the [Main] menu.

 

[Boot Option #1] is set to [CD/DVD Drive] in the [Boot] menu.

 

z When an external CD/DVD drive is connected, you cannot boot from the internal CD/

 

DVD drive.

You have forgotten the

z Supervisor Password or User Password: Contact your technical support office.

password.

z Administrator password:

 

If you have another account with Administrator authority, log-on with it, then delete the

 

password for the problem account.

 

If you have a password reset disk, click [Reset password] displayed after the password

 

 

input error, then follow the on-screen instructions to set a new password.

 

If you have a password reset disk, you can reset the administrator password. Set the

 

 

disk and enter any wrong password, then follow the on-screen instructions and set a

 

new password.

 

If you cannot do either of the above, you will need to reinstall (Î page 23) and setup

 

 

Windows.

“Remove disks or other

z A floppy disk is in the floppy disk drive and it does not contain system startup informa-

media. Press any key to

tion. Remove the floppy disk and press any key.

restart” or a similar mes-

z This message may appear with some devices connected to the USB port. Remove the

device or set [Legacy USB Support] to [Disabled] in the [Advanced] menu of the Setup Utility.

sage appears.

z If the problem persists after removing the disk, it may be a hard disk failure. Perform the rein-

 

stallation and return the hard disk to its condition at the time of purchase. (Î page 23) If the

 

problem persists even after the reinstallation, contact your technical support office.

[Executing Battery Recali-

z The Battery Recalibration was canceled before Windows was shut down last time. To

bration] screen appears.

start up Windows, turn off the computer by the power switch, and then turn on.

Troubleshooting Useful Information Getting Started

Appendix

25

Image 25
Contents Personal Computer ContentsIntroduction Appendix Troubleshooting Useful Information Getting Started„ Terms and illustrations in these instructions „ DisclaimerRead Me First Troubleshooting Useful Information Getting StartedModels for Europe Models for UKHow to replace the fuse Important Safety InstructionsRead Me First Appendix Troubleshooting Useful Information Lithium BatteryInformation to the User CD/DVD Drive CautionSafety Precautions Precautions Do Not Turn the Volume Up to Loud When Using Headphones Precautions Battery PackDo Not Look into the CD/DVD Drive Interface CableBattery pack may become warm during recharg Description of Parts Started Appendix Troubleshooting Useful Information GettingFirst-time Operation Insert the battery packOpen the display „ PreparationSetup Windows Connect your computer to a power outletTurn on the computer Handling the AC adaptorFirst-time Operation For MUI OS model Install Adobe ReaderCreate a new account For MUI OS model Change the language settingsChange the internal CD/DVD drive letter if necessary PC Information Viewer„ Note about access to the hard disk „ When Starting Up/Shutting Down z Do not do the following„ To change the partition structure For MUI OS model, 60000 MB or more is necessary On-screen Manual „ When the battery indicator does not light on Handling and MaintenanceOperation Environment Handling CautionsMaintenance Handling and MaintenanceIf You Spill Water on the Keyboard When Using the Computer with a Reduced Screen ResolutionTo display large characters with no blurring If there is water inside, wipe it using a soft, dry cloth Press F2 or Del while Panasonic boot screen is displayed Reinstalling SoftwareClick Reinstall Windows and click Next PreparationAt the confirmation message, click YES Reinstalling SoftwareAt the confirmation message, press Y Troubleshooting Useful Information Getting Started Appendix Troubleshooting Basic„ Starting Up and Sleep/Standby and Hibernation Mode „ Password Troubleshooting Basic„ Shutting Down „ Display „ BatteryUseful Information Getting Troubleshooting Appendix„ Touch Pad „ OthersLimited USE License Agreement „ Main Specifications SpecificationsCF-F9KWHZZPE CF-F9KWHZFPE CF-F9KWHZZDE CF-F9KWHZFDE „ Wireless LAN Only for model with wireless LAN„ Bluetooth Only for model with Bluetooth SpecificationsPanasonic Computer Products Europe Standard Limited WarrantyData Storage Media Standard Limited WarrantyAddress Contacts22-E-1
Related manuals
Manual 40 pages 35.32 Kb