Panasonic PT-D12000E Specifications, Please contact Panasonic or your dealer for a demonstration

Specifications

Power supply		220–240 V AC 16–9A, 50Hz/60Hz
Power consumption		1,500 W (15 W in standby mode with fan stopped)
DLP™ chip	Panel size	0.95" diagonal (4:3 aspect ratio)
	Display method	DLP™ chip x 3 (R, G, B), DLP™ projection system
Lens	Pixels	1,470,000 (1,400 x 1,050) x 3, total of 4,410,000 pixels
		Optional powered zoom/focus lenses
Lamp		300 W UHM™ lamp x 4 (four lamp system)
Screen size		70 - 600 inches,4:3 aspect ratio
Brightness*1		(70-300 inches, 4:3 aspect ratio with the ET-D75LE5)
		12,000 lumens (four-lamp operation mode)
Contrast ratio*1		5,000:1 (full on/full off, in Dynamic iris 3 mode)
Resolution		1,400 x 1,050 pixels (1,920 x 1,200 pixels compatible, compression mode)
RGB input scanning frequency		fH 15-100 kHz, fV 24-120 Hz
Component signal		Dot clock 20-162 MHz
		480i, 480p, 576i, 576p, 720/60p, 720/50p, 1035/60i, 1080/25p, 1080/24p,
Video signal		1080/24sF, 1080/30p, 1080/60i, 1080/50i, 1080/50p, 1080/60p
		fH 15.75/15.63 kHz, fV 50/60Hz
Lens shift		(NTSC,NTSC4.43,PAL,PAL60,PAL-N,PAL-M,SECAM)
		Vertical: ±50% (±40% with the ET-D75LE6) (powered)
Keystone correction range		Horizontal: ±30% (±20% with the ET-D75LE6) (powered)
		Vertical: ±40° (±22° with the ET-D75LE5, ±28° with the ET-D75LE6),
Terminals	DVI-D IN	Using Geometric Adjustment: Vertical ±10°, Horizontal ±15°
		DVI-D 24-pin x 1, DVI 1.0 compliant, compatible with HDCP, single link
		480p, 576p, 1080/60i, 1080/50i, 1080/24p, 1080/24sF, 1080/25p, 1080/30p, 1080/60p, 1080/50p,
		720/60p, 720/50p
		VGA (640 x 480) – WUXGA*2 (1,920 x 1,200), compatible with non-interlaced signals only,
	RGB1/YPBPR IN	Dot clock: 25–162 MHz
		BNC x 5
	RGB2 IN	D-sub HD 15-pin x 1
	VIDEO IN	BNC x 1, 1.0 Vp-p
	VIDEO OUT	BNC x 1, 1.0 Vp-p
	S-VIDEO IN	Mini DIN 4-pin x 1
	LAN	RJ-45 (10 Base-T/100 Base-TX) x 1, compatible with PJLink™
	SERIAL IN	D-sub 9-pin female x 2 (RS232C x 1, RS422 x 1)
	SERIAL OUT	D-sub 9-pin male x 1 (RS422 x 1)
	REMOTE 1 IN	M3 jack x1 for wired remote control
	REMOTE 1 OUT	M3 jack x1 for link control
	REMOTE 2 IN	D-sub 9-pin female x 1 for external control (parallel)
Optional board slot	With ET-MD77SD1	SERIAL IN: BNC x 1, SD-SDI signal (YCBCR 4:2:2 10-bit): SMPTE 259M compliant: 480i, 576i
	installed*3	SERIAL OUT: BNC x 1, active through
	With ET-MD77SD3	SERIAL IN: BNC x 1, SD-SDI signal (YCBCR 4:2:2 10-bit): SMPTE 259M compliant: 480i, 576i
	installed*3	Single-link HD-SDI signal (YCBCR 4:2:2 10-bit): SMPTE 292M compiant: 720/50p, 720/60p,
		1035/60i, 1080/50i, 1080/60i, 1080/25p, 1080/24p, 1080/24sF, 1080/30p
	With ET-MD100SD4	SERIAL OUT: BNC x 1, active through
		Link A/Link B IN: BNC x 1 for each, SD-SDI signal (YCBCR 4:2:2 10-bit): SMPTE 259M compliant: 480i, 576i
	installed	Single-link HD-SDI signal (YCBCR 4:2:2 10-bit): SMPTE 292M compiant: 720/50p, 720/60p, 1080/50i,
		1080/60i, 1080/25p, 1080/24p, 1080/24sF, 1080/30p
		Dual-link HD-SDI signal (RGB 4:4:4 12-bit/10-bit): SMPTE 372M compiant: 1920 x 1080/50i,
		1920 x 1080/60i, 1920 x 1080/25p, 1920 x 1080/24p, 1920 x 1080/24sF, 1920 x 1080/30p
		Dual-link HD-SDI signal (X'Y'Z' 4:4:4 12-bit): 2048 x 1080/24p, 2048 x 1080/24sF

Optional board slot With ET-MD77DV	Specifications are the same as those for the DVI-D IN terminal on the main unit.
installed
Installation	Front/rear, ceiling/floor
Power cord length	3.0 m (9.9")
Dimensions (W x H x D)	578 x 320 x 643 mm (22-3/4" x 12-19/32" x 25-5/16") (without lens)
Weight*4	Approx. 35 kg (77.1 lbs) without lens
Operating temperature	0 -45 °C (32 -113 °F)*5
Operating humidity	10-80% (no condensation)
Supplied accessories	Power cord, Wireless/wired remote control unit,
	Batteries for remote control (3V AA battery x2), Eye bolt x4, Wire rope

*1 Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards. *2 Only when using VESA CVT-RB(Reduced Blanking) signals.

*3 The LAN terminal on each board, when mounted, cannot be used because the LAN terminal on the main unit has priority. *4 Average value. May differ depending on models.

*5 The operating temperature range is 0°C (32°F) to 40°C (104°F) when used in High-Altitude mode (1,400 m [4,593 feet] to 2,700 m [8,858 feet]). Also, if the ambient temperature exceeds 40°C (104°F) (35°C [95°F] in High-Altitude mode) when using all four lamps, the light output may be reduced approximately 30% to protect the projector.

Dimensions		unit: mm (inch)
		643 (25-5/16")
	578 (22-3/4")	320 (12-19/32")

Projection distance

Diagonal

Throw distance

ET-D75LE6

ET-D75LE1

ET-D75LE2

ET-D75LE3

ET-D75LE4

ET-D75LE8

ET-D75LE5

image size

1.0-1.2:1

1.5-2.0:1

2.0-3.0:1

3.0-5.0:1

5.0-8.0:1

7.9-15.0:1

0.8:1

(aspect raio: 4:3)

min.

max.

min.

max.

min.

max.

min.

max.

min.

max.

min.

max.

fixed

70"

1,393 mm

1,662 mm

2,072 mm

2,768 mm

2,801 mm

4,215 mm

4,226 mm

7,094 mm

7,101 mm

11,374 mm

11,091 mm

21,142 mm

1,022 mm

4.6'

5.4'

6.9'

9.0'

9.2'

13.8'

13.9'

23.2'

23.3'

37.3'

36.4'

69.3'

3.3'

100"

2,014 mm

2,406 mm

2,992 mm

3,998 mm

4,035 mm

6,067 mm

6,077 mm

10,187 mm

10,193 mm

16,292 mm

16,009 mm

30,358 mm

1,496 mm

6.7'

7.8'

9.9'

13.1'

13.3'

19.9'

20.0'

33.4'

33.5'

53.4'

52.6'

99.5'

4.9'

150"

3,049 mm

3,646 mm

4,526 mm

6,047 mm

6,093 mm

9,153 mm

9,164 mm

1,5341 mm

1,5348 mm

24,488 mm

24,207 mm

45,717 mm

2,286 mm

10.0'

11.9'

14.8'

19.8'

19.9'

30.0'

20.2'

50.3'

50.3'

80.3'

79.4'

149.9'

7.5'

200"

4,084 mm

4,886 mm

6,060 mm

8,096 mm

8,150 mm

12,240 mm

12,250 mm

20,496 mm

20,502 mm

32,685 mm

32,404 mm

61,076 mm

3,076 mm

13.5'

16.0'

19.9'

26.5'

26.8'

40.1'

40.2'

67.2'

67.3'

107.2'

106.3'

200.3'

10.0'

300"

6,154 mm

7,366 mm

9,128 mm

12,194 mm

12,265 mm

18,413 mm

18,423 mm

30,805 mm

30,811 mm

49,078 mm

48,799 mm

91,794 mm

4,656 mm

20.2'

24.1'

30.0'

40.0'

40.3'

60.3'

60.5'

101.0'

101.1'

160.9'

160.1'

301.0'

15.2'

400"

8,224 mm

9,846 mm

12,196 mm

16,292 mm

16,380 mm

24,586 mm

24,596 mm

41,114 mm

41,120 mm

65,471 mm

65,194 mm

122,512 mm

—

27.0'

32.2'

40.1'

53.4'

53.8'

80.6'

80.7'

134.8'

134.9'

214.7'

213.9'

401.8'

600"

12,364 mm

14,806 mm

18,332 mm

24,488 mm

24,610 mm

36,932 mm

36,942 mm

61,732 mm

61,738 mm

98,257 mm

97,984 mm

183,948 mm

—

40.6'

48.5'

60.2'

80.3'

80.8'

121.1'

121.2'

202.4'

202.6'

322.2'

321.4'

603.3'

NOTES ON USE

1.Do not install the projector in locations that are subject to excessive water, humidity, steam, or oily smoke. Doing so may result in fire, malfunction, or electric shock.

2.The projector uses a high-voltage mercury lamp that contains high internal pressure. This lamp may break, emitting a large sound, or fail to illuminate, due to impact or extended use.

3.The projector uses of high-wattage lamp that becomes very hot during operation. Please observe the following precautions.

•Never place objects on top of the projector while it is operation.

•Make sure there is an unobstructed space of 500 mm or more around the projector’s exhaust openings.

•Do not stack projector units directly on top of one another for the purpose of multiple (stacked) projection.

When stacking projector units, be sure to provide the amount of space indicated between them. These space requirements also apply to installation where only one projector unit is operating at one time and the other unit is used as a backup.

•If the projector is placed in a box or enclosure, temperature of the air surrounding the projector must be between 0°C and 35°C. Also make sure the projector’s intake and exhaust openings are not blocked. Take particular care to ensure that hot air from the exhaust openings is not sucked into the intake.

4.If the projector is to be operated continuously 24 hours a day, use the multi-lamp optical system’s alternating lamp operation (lamp changer) function. The projector can be operated continuously 24 hours a day in four-lamp operation mode, but it will automatically operate with three lamps for 8 hours of the 24 hours.

5.The lamp replacement cycle duration becomes shorter if the projector is operated repeatedly for short periods.

•The length of time that it takes for the lamp to break or fail to illuminate varies greatly depending on individual lamp characteristics and usage conditions.

•The brightness of the lamp will gradually decrease with use.

6.Because the ET-D75LE5 is a fixed short-throw lens, the lens shift function cannot be used with it.

7.Due to natural characteristics of lamps, screen brightness may vary (flicker). This is not an indication of faulty lamp performance.

R

For more information about Panasonic projector ––

http://panasonic.net/pavc/projector

Please contact Panasonic or your dealer for a demonstration.

JQA-1617 EC98J2010

Weights and dimensions shown are approximate. Specifications are subject to change without notice. This product may be subject to export regulations. UHM is trademark of Matsushita Electric Indusutrial Co., Ltd. VGA and XGA are trademarks of International Business Machines Corporation. All other trademarks are the property of their respective trademark owners. Projection Images simulated.

DLP, DLP logo and DLP Medallion logo are trademarks or registered trademarks of Texas Instruments. The PJLink trademark is an application trademark in Japan, the United States, and other countries and regions or registered trademarks.

(C)2008 Panasonic Projector Systems Company is a Unit of Panasonic Corporation of North America. All rights reserved.

(C)2008 Matsushita Electric Industrial Co,Ltd. All rights reserved.

All information included here is valid as of July 2008.

PT-D12KE1-08July10K Printed in Japan.