Panasonic PT-DW100 specifications Specifications

Specifications

Power supply		North America: 120–240 V AC, 16 – 9.0 A, 50/60 Hz (3-wire single-phase)
		Europe, Asia: 220–240 V AC, 9.5 A, 50/60 Hz (3-wire single-phase)
Power consumption		North America: 1,600–1,500 W (10-15 W in standby mode with fan stopped)
		Europe, Asia: 1,500 W (15 W in standby mode with fan stopped)
DLP™ chip	Panel size	0.85" diagonal (16:9 aspect ratio)
	Display method	DLP™ chip x 3 (R, G, B), DLP™ projection system
	Pixels	1,049,088 (1,366 x 768) x 3, total of 3,147,264 pixels
Lens		Optional powered zoom/focus lenses
Lamp		300 W UHM lamp x 4 (four lamp system)
Screen size		70 - 600 inches,16:9 aspect ratio
		(70-300 inches, 16:9 aspect ratio with the ET-D75LE5)
Brightness*1		10,000 lumens (four-lamp operation mode)
Contrast ratio*1		5,000:1 (full on/full off, in Dynamic iris 3 mode)
Resolution		1,366 x 768 pixels (Input signals that exceed this resolution will be converted to 1,366 x 768 pixels.)
RGB input scanning frequency		fH 15-100 kHz, fV 24-120 Hz
		Dot clock 20-162 MHz
Component signal		480i, 480p, 576i, 576p, 720/60p, 720/50p, 1035/60i, 1080/25p, 1080/24p,
		1080/24sF, 1080/30p, 1080/60i, 1080/50i, 1080/50p, 1080/60p
Video signal		fH 15.75/15.63 kHz, fV 50/60Hz
		(NTSC,NTSC4.43,PAL,PAL60,PAL-N,PAL-M,SECAM)
Lens shift		Vertical: ±70% (±60% with the ET-D75LE6) (powered)
		Horizontal: ±30% (±20% with the ET-D75LE6) (powered)
Keystone correction range		Vertical: ±40° (±22° with the ET-D75LE5, ±28° with the ET-D75LE6)
Terminals	DVI-D IN	DVI-D 24-pin x 1, DVI 1.0 compliant, compatible with HDCP, single link
		480p, 576p, 1080/60i, 1080/50i, 1080/24p, 1080/24sF, 1080/25p, 1080/30p, 1080/60p, 1080/50p,
		720/60p, 720/50p
		VGA (640 x 480) – WUXGA*2 (1,920 x 1,200), compatible with non-interlaced signals only,
		Dot clock: 25–162 MHz
	RGB1/YPBPR IN	BNC x 5
	RGB2 IN	D-sub HD 15-pin x 1
	VIDEO IN	BNC x 1, 1.0 Vp-p
	VIDEO OUT	BNC x 1, 1.0 Vp-p
	S-VIDEO IN	Mini DIN 4-pin x 1
	LAN	RJ-45 (10 Base-T/100 Base-TX) x 1, compatible with PJLink™

Optional Accessories

Lens

Zoom lens

ET-D75LE6(1.0-1.2:1)

ET-D75LE1(1.5-2.0:1)

ET-D75LE2(2.1-3.1:1)

ET-D75LE3(3.1-5.2:1)

ET-D75LE4(5.2-8.2:1)

ET-D75LE8(8.2-15.4:1)

Fixed focus lens

ET-D75LE5 (0.8:1)

ET-D75LE1

Lamp

Replacement lamp unit

ET-LAD12K

ET-LAD12KF (four pack)

Input signal board

SD-SDI input signal board

ET-MD77SD1

HD/SD-SDI input signal board

ET-MD77SD3

Dual link HD/HD-SDI input signal board

ET-MD100SD4

DVI-D input signal board

ET-MD77DV

Smoke cut filter

ET-SFD100

This optional

smoke filter must be used for staging events where smoke or fog is dispersed.

Frame

ET-PFD100

Carrying handle

ET-HAD100

Ceiling mount bracket

High-ceiling	Low-ceiling
mount bracket	mount bracket
ET-PKD100H	ET-PKD100S
	ET-PKD100S
ET-PKD100H

SERIAL IN	D-sub 9-pin female x 2 (RS232C x 1, RS422 x 1)
SERIAL OUT	D-sub 9-pin male x 1 (RS422 x 1)
REMOTE 1 IN	M3 jack x 1 for wired remote control
REMOTE 1 OUT	M3 jack x 1 for link control
REMOTE 2 IN	D-sub 9-pin female x 1 for external control (parallel)
Optional board slot With ET-MD77SD1	SERIAL IN: BNC x 1, SD-SDI signal (YCBCR 4:2:2 10-bit): SMPTE 259M compliant: 480i, 576i
installed*3	SERIAL OUT: BNC x 1, active through
With ET-MD77SD3	SERIAL IN: BNC x 1, SD-SDI signal (YCBCR 4:2:2 10-bit): SMPTE 259M compliant: 480i, 576i
installed*3	Single-link HD-SDI signal (YCBCR 4:2:2 10-bit): SMPTE 292M compliant: 720/50p, 720/60p,
	1035/60i, 1080/50i, 1080/60i, 1080/25p, 1080/24p, 1080/24sF, 1080/30p
	SERIAL OUT: BNC x 1, active through
With ET-MD100SD4	Link A/Link B IN: BNC x 1 for each, SD-SDI signal (YCBCR 4:2:2 10-bit): SMPTE 259M compliant: 480i, 576i
installed	Single-link HD-SDI signal (YCBCR 4:2:2 10-bit): SMPTE 292M compliant: 720/50p, 720/60p, 1080/50i,
	1080/60i, 1080/25p, 1080/24p, 1080/24sF, 1080/30p
	Dual-link HD-SDI signal (RGB 4:4:4 12-bit/10-bit): SMPTE 372M compliant: 1920 x 1080/50i,
	1920 x 1080/60i, 1920 x 1080/25p, 1920 x 1080/24p, 1920 x 1080/24sF, 1920 x 1080/30p
	Dual-link HD-SDI signal (X'Y'Z' 4:4:4 12-bit): 2048 x 1080/24p, 2048 x 1080/24sF
With ET-MD77DV	Specifications are the same as those for the DVI-D IN terminal on the main unit.

Ecological-conscious design

Panasonic works from every angle to minimize environmental impact in the product design, production and delivery processes, and in the performance of the product during its life cycle. The PT-DW100 reflects the following ecological considerations.

•Lead-free solder is used to mount components to the printed circuit boards. •Lamp power switching further reduces power consumption.

•Auto Power Save activates standby mode when no signal is input.

Dimensions

Made in Japan

PT-DW100 projector is carefully manufactured at the Panasonic factory in Japan under strict quality control. This is another very important advantage of Panasonic projectors.

unit: mm (inch)

installed
Installation	Front/rear, ceiling/floor
Power cord length	3.0 m (9.8')
Dimensions (W x H x D)	578 x 320 x 643 mm (22-3/4" x 12-19/32" x 25-5/16") (without lens)
Weight*4	Approx. 35 kg (77.2 lbs) without lens
Operating temperature	0 -45 °C (32 -113 °F)*5
Operating humidity	10-80% (no condensation)
Supplied accessories	Power cord, Wireless/wired remote control unit,
	Batteries for remote control (3V AA battery x2), Eye bolt x4, Wire rope

*1 Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards. *2 Only when using VESA CVT-RB(Reduced Blanking) signals.

*3 The LAN terminal on each board, when mounted, cannot be used because the LAN terminal on the main unit has priority. *4 Average value. May differ depending on models.

*5 The operating temperature range is 0°C (32°F) to 40°C (104°F) when used in High-Altitude mode (1,400 m [4,593 feet] to 2,700 m [8,858 feet]). Also, if the ambient temperature exceeds 40°C (104°F) (35°C [95°F] in High-Altitude mode) when using all four lamps, the light output may be reduced approximately 30% to protect the projector.

	643 (25-5/16")
578 (22-3/4")	320 (12-19/32")

Projection distance

Diagonal image size

Throw distance

ET-D75LE6

ET-D75LE1

ET-D75LE2

ET-D75LE3

ET-D75LE4

ET-D75LE8

ET-D75LE5

(aspect raio: 16:9)

1.0-1.2:1

1.5-2.0:1

2.1-3.1:1

3.1-5.2:1

5.2-8.2:1

8.2-15.4:1

0.8:1

min.

max.

min.

max.

min.

max.

min.

max.

min.

max.

min.

max.

fixed

70"

1,560 mm

1,865 mm

2,322 mm

3,103 mm

3,137 mm

4,719 mm

4,730 mm

7,937 mm

7,943 mm

12,713 mm

12,430 mm

23,652 mm

1,151 mm

5.1'

6.1'

7.6'

10.2'

10.3'

15.5'

15.5'

27.9'

27.9'

41.7'

40.8'

77.6'

3.8'

100"

2,253 mm

2,696 mm

3,349 mm

4,476 mm

4,516 mm

6,787 mm

6,798 mm

11,391 mm

11,397 mm

18,206 mm

17,923 mm

33,943 mm

1,681 mm

7.4'

8.8'

11.0'

14.7'

14.8'

22.3'

22.3'

39.9'

39.9'

59.7'

58.8'

111.4'

5.5'

150"

3,408 mm

4,081 mm

5,062 mm

6,765 mm

6,814 mm

10,234 mm

10,244 mm

17,147 mm

17,153 mm

27,359 mm

27,077 mm

51,095 mm

2,563 mm

11.2'

13.4'

16.6'

22.2'

22.4'

33.6'

33.6'

59.9'

59.9'

89.8'

88.8'

167.6'

8.4'

200"

4,563 mm

5,466 mm

6,775 mm

9,053 mm

9,112 mm

13,680 mm

13,691 mm

22,904 mm

22,909 mm

36,512 mm

36,232 mm

68,246 mm

3,445 mm

15.0'

17.9'

22.2'

29.7'

29.9'

44.9'

44.9'

79.9'

79.9'

119.8'

118.9'

223.9'

11.3'

300"

6,873 mm

8,236 mm

10,201 mm

13,630 mm

13,707 mm

20,574 mm

20,584 mm

34,416 mm

34,422 mm

54,819 mm

54,541 mm

102,549 mm

5,209 mm

22.6'

27.0'

33.5'

44.7'

45.0'

67.5'

67.5'

119.9'

119.9'

179.9'

178.9'

336.4'

17.1'

400"

9,183 mm

11,006 mm

13,626 mm

18,206 mm

18,303 mm

27,467 mm

27,477 mm

45,929 mm

45,934 mm

73,126 mm

72,850 mm

136,852 mm

—

30.1'

36.1'

44.7'

59.7'

60.0'

90.1'

90.1'

159.9'

159.9'

239.9'

239.0'

449.0'

600"

13,803 mm

16,546 mm

20,477 mm

27,360 mm

27,494 mm

41,254 mm

41,264 mm

68,954 mm

68,960 mm

109,740 mm

109,468 mm

205,458 mm

—

45.3'

54.3'

67.2'

89.8'

90.2'

135.3'

135.4'

239.9'

239.9'

360.0'

359.1'

674.1'

NOTES ON USE

1.Do not install the projector in locations that are subject to excessive water, humidity, steam, or oily smoke. Doing so may result in fire, malfunction, or electric shock.

2.The projector uses a high-voltage mercury lamp that contains high internal pressure. This lamp may break, emitting a large sound, or fail to illuminate, due to impact or extended use.

3.The projector uses high-wattage lamp that becomes very hot during operation. Please observe the following precautions.

•Never place objects on top of the projector while it is in operation.

•Make sure there is an unobstructed space of 500 mm or more around the projector’s exhaust openings.

•Do not stack projector units directly on top of one another for the purpose of multiple (stacked) projection.

When stacking projector units, be sure to provide the amount of space indicated between them. These space requirements also apply to installation where only one projector unit is operating at one time and the other unit is used as a backup.

•If the projector is placed in a box or enclosure, temperature of the air surrounding the projector must be between 0°C and 35°C. Also make sure the projector’s intake and exhaust openings are not blocked. Take particular care to ensure that hot air from the exhaust openings is not sucked into the intake.

4.If the projector is to be operated continuously 24 hours a day, use the multi-lamp optical system's alternating lamp operation (lamp changer) function. The projector can be operated continuously 24 hours a day in four-lamp operation mode, but it will automatically operate with three lamps for 8 hours of the 24 hours.

5.The lamp replacement cycle duration becomes shorter if the projector is operated repeatedly for short periods.

•The length of time that it takes for the lamp to break or fail to illuminate varies greatly depending on individual lamp characteristics and usage conditions.

•The brightness of the lamp will gradually decrease with use.

6.Because the ET-D75LE5 is a fixed short-throw lens, the lens shift function cannot be used with it.

7.Due to natural characteristics of lamps, screen brightness may vary (flicker). This is not an indication of faulty lamp performance.

For more information about Panasonic projector ––

http://panasonic.net/avc/projector

Please contact Panasonic or your dealer for a demonstration.

JQA-1617EC98J2010

Weights and dimensions shown are approximate. Specifications are subject to change without notice. This product may be subject to export regulations. VGA and XGA are trademarks of International Business Machines Corporation.

All other trademarks are the property of their respective trademark owners. Projection Images simulated.

DLP, DLP logo and DLP Medallion logo are trademarks or registered trademarks of Texas Instruments. The PJLink trademark is an application trademark in Japan, the United States, and other countries and regions or registered trademarks.

(C) 2008 Panasonic Corporation All rights reserved.

All information included here is valid as of October 2008.

PT-DW100-08October50K Printed in Japan.