Outlaw Audio 7500, 7700 Connecting Your Amplifier, Audio Signal Connections, Speaker Connections

Page 5

Connecting Your Amplifier

When making connections between any source components and the ampli- fier, or when making connections to any speaker, be certain that both the input devices and the amplifier are turned off. To assure that there will be no unwanted signal transients that can damage equipment or speakers, it is always best to unplug all equipment before making any connections. Modern electronic products often have a standby mode that may be activated even though the product may appear to be turned off.

Audio Signal Connections

Connections with RCA type plugs:

When making connections with the “RCA” type plugs on interconnect cables, make certain to gently, but firmly insert them into the jacks marked “unbal- anced input” on the back of the Model 7700/7500. Place input toggle in the “Unbalanced” position before attempting to operate. Loose connections can cause intermittent sound and may damage your speakers. The barrel assembly of some high quality RCA plugs may be very tight, and it is important to ensure

a proper connection between the interconnect cable and the input jack.

Connections with XLR (Balanced) audio type plugs:

When making connections with “XLR” type plugs on balanced interconnect cables, make certain to gently, but firmly insert them into the jacks marked “balanced input” on the back of the Model 7700/7500. Set the input toggle in the “Balanced” position before attempting to operate. Loose connections can cause intermittent sound and may damage your speakers.

IMPORTANT NOTE: When releasing an XLR connector from an input jack, press the “plate” style tab on the input jack (male end of cable) and pull the interconnect straight out. When releasing an XLR con- nector from an output jack, press the “button” style tab on the XLR connector (female end of cable) and pull the interconnect straight out.

Unlike “turbine” style RCA cables, twisting the interconnect will damage the cable and input jack on your amplifier.

Speaker Connections

To assure that the high quality signals produced by your Outlaw amplifier are carried to your speakers without loss of clarity or resolution, we recommend that you use high quality speaker wire. Many brands of wire are available; the choice may be influenced by the distance between your speakers and the amplifier, the type of speakers you use, personal preferences, or other factors.

Regardless of the brand or type of speaker wire selected, we recommend that you use a wire constructed of fine, multi-strand copper with a gauge of 14 or less. Remember that in specifying wire, the lower the number, the thicker the cable. Wire with a gauge of 16 may be used for short runs of less than ten feet. We do not recommend that you use any wires with an AWG equivalent of 18 or higher due to the power loss and degradation in performance that will occur.

To connect the amplifier to your speakers a pair of binding posts is provided for each channel output. These posts will accept bare wire, spade lugs or banana type plugs, when they are permitted by local safety agencies.

If bare wire is used for the connections, strip approximately 1/2 inch to 3/4 inch (20mm) of insulation from the end of each wire and carefully twist the

Owner’s Manual

Connecting Your Amplifier

strands of each conductor together. Be careful not to cut the individual strands or twist them off. For optimal performance, all strands must be used.

Correct polarity connections are important to maintain proper speaker phasing. When speaker phasing is correct, all speakers move in and out at the same time, preserving the imaging of the program material. Out-of-phase connections mean that some speaker cones will be moving in, while others move out. This will cause indistinct or confused imaging, and muddled and cloudy sounds. To avoid incorrect phasing or polarity, be certain to use cable that has distinct markings, colors, stripes, wording, or grooves on each side of the speaker cable. When mak- ing connections to the amp and speakers, adhere to a consistent pattern of using one side of the wire to the red terminals and the other side to the black terminals. When using cable with markings on one side only, traditional convention is to consider the marked side of the wire as the red, or positive (+) connection, and the non-marked side as the black or negative (-) connection.

Next, loosen the knobs of the amplifier’s speaker output terminals, far enough so that the pass through hole is revealed. Note that one conductor of the speaker cable should have no markings, and the other should have a red line, brand name markings, a colored thread, or some other positive indication. Follow the proper connection instructions for your system with regard to which terminals are used. Once the connections are made, twist the cap back so that the con- nection is secured, but do not over tighten or use tools, as this may break the delicate wire strands and decrease system performance.

If you are using spade lugs, connect them to the speaker wire using the man- ufacturer’s instructions, then loosen the caps on the speaker terminals. Place lugs between the plastic cap and the back of the terminal. Be sure to observe proper polarity, using the appropriate speaker hook-up icons for your system’s configuration. Using your fingers, tighten to obtain a positive contact.

When using banana plugs, connections may be made by simply inserting the jack affixed to your speaker wire into the hole provided on the rear of the colored screw caps on the binding posts. Before using banana type jacks make certain that the plastic screw caps are firmly tightened down by turning them in a clockwise direction until they are snug against the chassis. This will insure that the maximum surface area of the plug is in contact with the jack. Be certain to observe proper polarity.

Run the cables to the speaker locations. It is recommended that the length of wire connecting any pair of speakers be similar. For example, make certain that the wire length connecting the left and right front, or the left and right rear (surround) speakers are similar in length, even though one speaker may be physically closer to the amplifier than the other. Do not coil any excess cable, as this may become an inductor that creates frequency response variations in your system.

Finally, connect the wires to the speakers, again being certain to observe proper polarity. Remember to connect your negative, or black wire, to the matching terminal on the speaker. The positive, or red wire, should be connected to the matching terminal on the speaker.

NOTE: While most speaker manufacturers adhere to an industry conven- tion of using red terminals for positive connections and black terminals for negative, some manufacturers may vary from this configuration. To assure proper phase connections, and optimal performance, consult the identification plate on your speaker terminals, or the speaker’s manual to verify polarity. If you do not know the polarity of your speaker, consult the speaker’s manufacturer for further information.

Model 7700/7500 Multi-Channel Power Amplifier

Image 5
Contents Model 7500 5-Channel Power Amplifier Please Read First Unpacking Table of ContentsFeatures Unbalanced Audio Inputs Rear PanelSpeaker Connections Connecting Your AmplifierAudio Signal Connections Model 7700 Rear Panel Connections Model 7500 Rear Panel Connections Amplifier Operation Care and MaintenanceTroubleshooting Guide TroubleshootingOutlaw Service Information Few Words About Hum and NoisePotential Ground Loops in a Complex A/V System Specifications Outlaw Audio Limited Warranty Outlaw Audio 30-Day Satisfaction Guarantee

7500, 7700 specifications

Outlaw Audio has made a name for itself in the high-performance audio market, particularly with its impressive lineup of amplifiers. Among these, the Outlaw Audio 7500 and 7700 models stand out for their robust capabilities and advanced features, which cater to audiophiles seeking premium sound quality for their home theater systems.

The Outlaw Audio 7500 is a 5-channel power amplifier that delivers a remarkable 120 watts per channel into 8 ohms, with the ability to produce more power at lower impedances. This amplifier is engineered with high-current, high-damping-factor output to ensure that it handles even the most demanding speakers with ease, resulting in clean, clear sound reproduction. Its Class AB topology provides a good balance between efficiency and sound quality, allowing for dynamic sound performance without compromising on detail.

On the other hand, the Outlaw Audio 7700 takes the performance a step further, featuring a 7-channel configuration with the same power output per channel as the 7500. This model is particularly well-suited for more expansive home theater setups, handling additional speaker channels without breaking a sweat. Both amplifiers incorporate advanced technologies designed to maximize audio fidelity and minimize distortion, ensuring that sound professionals and home theater enthusiasts alike can enjoy a cinematic audio experience.

One of the standout characteristics of both models is their build quality. Constructed with a heavy-duty chassis, these amplifiers are designed to minimize resonance and interference, contributing to their impressive audio clarity. The outboard power supply on both units also enhances performance by providing clean power to the amplifiers' output stages, further reducing noise and distortion.

In terms of connectivity, both the 7500 and 7700 come equipped with RCA inputs for easy integration into any home theater setup, along with a detachable power cord for flexible installation. Additionally, their design includes thermal protection features and reliable circuitry to ensure longevity and consistent performance.

In conclusion, the Outlaw Audio 7500 and 7700 are exceptional amplifiers that deliver powerful, high-quality sound for home theater enthusiasts. With their robust construction, high-performance features, and user-friendly connectivity options, these models embody Outlaw Audio's commitment to auditory excellence, making them an ideal choice for those looking to elevate their listening experience.