Rockford Fosgate 150, 800, 100, 500, 250 manual

Page 14

3.Strip 1/2" from the battery end of the power cable and crimp a large ring terminal to the cable. Use the ring terminal to connect to the battery positive terminal. Do not install the fuse at this time.

4.Prepare the Ground cable for attachment to the amplifier by stripping 1/ 2" of insulation from the end of the wire. Insert the bared wire into the GND terminal and tighten the set screw to secure the cable in place. Prepare the chassis ground by scraping any paint from the metal surface and thoroughly clean the area of all dirt and grease. Strip the other end of the wire and attach a ring connector. Fasten the cable to the chassis using a non-anodized screw and a star washer.

5.Prepare the REM turn-on wire for connection to the amplifier by stripping 1/2" of insulation from the wire end. Insert the bared wire into the REM terminal and tighten the set screw to secure the cable into place. Connect the other end of the REM wire to a switched 12 volt positive source. The switched voltage is usually taken from the source unit's auto antenna or the accessory lead. If the source unit does not have these outputs available, the recommended solution is to wire a mechanical switch in line with a 12 volt source to activate the amplifier.

6.Securely mount the amplifier to the vehicle or amp rack. Be careful not to mount the amplifier on cardboard or plastic panels. Doing so may enable the screws to pull out from the panel due to road vibration or sudden vehicle stops.

7.Connect the source signal to the amplifier by plugging the RCA cables/ high level inputs into the input jacks at the amplifier.

8.Connect the speakers. Strip the speaker wires 1/2" and insert into the speaker terminal and tighten the set screw to secure into place. Be sure to maintain proper speaker polarity. DO NOT chassis ground any of the speaker leads as unstable operation may result.

9.Perform a final check of the completed system wiring to ensure that all connections are accurate. Check all power and ground connections for frayed wires and loose connections which could cause problems.

– 9 –

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Punch E C I F I C AT I O N S Crossover Slope Per channel into a 2Ω LoadPer channel into a 4Ω Load Crossover FrequencyPractice Safe Sound Table of Contents T T I N G S T a R T E DPunch Amplifier Accessory Pack T R O D U C T I O NStable Into each channel Stable into bridged/mono Punch 2-CHANNEL Amplifier Feature ChartRMS Power per channel 2Ω Die Cast Heatsink4Phase Warp 00 ~ 100 150 250 360 500 800 Adjustable Punch BassVariable Punch Bass 0dB ~+18dB @ 45Hz Adjustable Xover 80Hz Dimensions H x W x LDesign Features PunchPage Installation Considerations Passenger Compartment Mounting Mounting LocationTrunk Mounting Engine Compartment MountingAppropriate inline connectors. Use the section Battery and ChargingWiring the System Page Using Passive Crossovers Table of Crossover Component Values Speaker ImpedancePunch 250 / Punch 360 / Punch InstallationPower Connections Punch 100 / Punch Power Connections Punch RCA Inputs High Level InputsPunch Bass Operation Crossover OperationStereo Operation Punch 100 / Punch Stereo Operation Punch 250 / Punch 360 / Punch 500 / PunchMono Operation Punch 100 / Punch Mono Operation Punch 250 / Punch 360 / Punch 500 / PunchStereo/Mono Operation Punch 100 / Punch RCA InputSystem Diagrams Way SystemWay System Using single voice coil woofers Way System Using dual voice coil woofers Troubleshooting Symptom Diagnosis RemedyTurn-on Pop Turn-on lead is entering Signal cableVoltage spike from remote Turn-on outputMusic Dynamic Power MeasurementsAbout the Dynamic Power Measurements Listening to Loudspeakers Not ResistorsInformation Cubed What is an Amplifier?Example of a Punch 200.2 PowerCube Limited Warranty Information Myrtle N.WPage Instalacion Montaje en el MalateroMontaje en el Compartimento de Pasajeros Terminal B+Crossover en Full Range Terminal GNDTerminal REM No llevar a masa ningun cable de altavozMontage dans lhabitacle InstallationMontage dans le coffre Opération stéréo/mono tri mode FrançaisEinbau Im FahrzeugkofferraumAuf der Beifahrerseite + AnschluβStereo/Mono Operation GND AnschluβREM Anschluβ Nellabitacolo InstallazioneNel Bagagliaio Terminale B+ cavo positivoTerminale GND cavo negativo Terminale REM Consenso di accensioneHandcrafted in the United States of America

150, 250, 500, 100, 800 specifications

Rockford Fosgate has long been recognized as a leader in the automotive audio industry, and their amplifier lineup, including models like the 500, 150, 250, 800, and 100, exemplifies the brand's commitment to power and performance. Each model brings unique features, technologies, and characteristics designed to cater to a wide variety of audio enthusiasts.

The Rockford Fosgate 500 amplifier, known for its impressive power output, delivers 500 watts of dynamic sound. One of its standout features is the integrated C.L.E.A.N. technology, which ensures a distortion-free experience by allowing users to set the optimal input levels. This model is ideal for those looking to drive subwoofers without compromising quality.

Another compact yet powerful option is the Rockford Fosgate 150 amplifier. This model is designed for smaller installations but does not skimp on performance. With a peak wattage of 150 watts and a built-in crossover, the 150 is perfect for enhancing speaker systems by providing clear, loud audio without the bulk. The include a low-pass crossover ensures seamless integration with subwoofers.

The Rockford Fosgate 250 takes performance a step further, delivering 250 watts. This model features efficient thermal management with an aluminum heat sink, ensuring durability and reliability even under high usage conditions. The adjustable gain control makes it easy for users to match the amplifier to their specific audio needs.

For those who seek more power, the Rockford Fosgate 800 amplifier offers an impressive 800 watts and is designed for maximum output in both mono and stereo configurations. It features a variable low-pass filter and a bass boost function, allowing users to customize their sound signature to fit individual preferences.

Lastly, the Rockford Fosgate 100 amplifier provides a solid introduction to the brand's high-performance amplifiers, offering 100 watts of power. It is an excellent choice for entry-level users who want to upgrade their sound system without diving into higher-end options. Its rugged design and reliable performance make it a preferred choice among many.

Overall, Rockford Fosgate amplifiers—500, 150, 250, 800, and 100—demonstrate a range of features tailored to meet different audio needs. Whether you are an audiophile or a casual listener, each model incorporates advanced technologies to deliver high-quality sound, making them a staple in the automotive aftermarket audio sphere.
Top Page Image Contents