Zebra Technologies GX430t, GX420t manual Platen Cleaning and Replacement

Page 82

70

Maintenance

Cleaning

Platen Cleaning and Replacement

The standard platen (drive roller) normally does not require cleaning. Paper and liner dust can accumulate without effecting print operations. Contaminates on the platen roller can damage the printhead or cause the media to slip or stick when printing. Adhesive, dirt, general dust, oils and other contaminates should be cleaned immediately off the platen.

Clean the platen (and media path) whenever the printer has significantly poorer performance, print quality or media handling. The platen is the print surface and drive roller for your media. If sticking or jamming continues even after cleaning, you must replace the platen.

The platen can be cleaned with a fiber-free swab (such as a Texpad swab) or a lint free, clean, damp cloth very lightly moistened with medical grade alcohol (90% pure or better).

1.Open the cover (and dispenser door). Remove media from platen area.

2.Pull the platen bearing latch release tabs on the right and left sides towards the front of the printer and rotate them up.

Platen Bearings

980612-001 Rev. A

GX420t / GX430t User Guide

12/14/07

Page 81 Page 83
Image 82
Page 81 Page 83
Contents Zebra GX420t / GX430t Proprietary Statement Iii Environmental Management About This Document Who Should Use This Document How This Document Is OrganizedAmericas ContactsWeb Site Europe, Africa, Middle East, and IndiaDocument Conventions Icons UsedContents Print Operations Maintenance Xii Introduction GX Series Thermal Printers What’s in the Box? Unpack and Inspect the PrinterYour Printer Opening the printerPrinter Features GAPMoveable Blackline Sensor Option Media Cutter Operator Controls Power Switch Feed ButtonStatus Light Closing the printer Lower the top cover Press down until the cover snaps closedIntroduction What’s in the Box? Getting Started Attaching Power Loading Roll Media Preparing MediaPlacing the Roll in the Media Compartment Getting Started Loading Roll Media Close the printer. Press down until the cover snaps closed Loading Transfer Ribbon Getting Started Loading Transfer Ribbon Getting Started Loading Transfer Ribbon Your printer is now ready to print Printing a Test Printer Configuration Label Hooking Up the Printer and Computer Interface Cable RequirementsUSB Interface Requirements Serial Communications EPL Y Command Parallel Port Ethernet Communicating with the Printer Universal Serial Bus USB CommunicationsPrint Operations Determining Printer Configuration Thermal PrintingModes of Printing Print Media TypesTypes of Media Roll and Fanfold Media Determining Thermal Media Types Replacing SuppliesAdding a New Transfer Ribbon Adjusting the Print Quality Adjusting the Print WidthReplacing a Partially Used Transfer Ribbon Media Sensing Ribbon Overview When to Use RibbonCoated Side of Ribbon Ribbon Scratch Test Printing on Fan-Fold Media Print Operations Printing on Fan-Fold Media Printing with Externally Mounted Roll Media Externally Mounted Roll Media ConsiderationsFonts and Your Printer Identifying Fonts in Your PrinterAsian fonts and Other Large Font Sets Localizing the Printer with Code PagesGetting Asian Fonts Stand Alone Printing Sending Files to the Printer Transferring files with the Firmware DownloaderPrint Operations Sending Files to the Printer Print Meter Printer Options Label Dispenser Option XA MMP XZPrinter Options Label Dispenser Option Printer Options Label Dispenser Option Moveable Blackline Sensor Option Black Marks Printer Options Moveable Blackline Sensor Option Maximum Paper Weight thickness up to 180 g/m2 0.0077 Cutter OptionLoading Media with the Cutter Option Printer Options Cutter Option Close the printer. Press down until the cover snaps closed ZebraNet 10/100 Internal Print Server Option Printer Network Configuration Status Label RTC and Full Flash Memory Option Asian Fonts Printer Accessory KDU Printer Accessory KDU and G-Series Printer Serial Port Adapter Installation KDU Plus Printer Accessory 45mA + 120mA + 25mA + 50mA Max. CurrentMaintenance Cleaning See Cleaning the Printhead onCleaning the Printhead Media Path Considerations Sensor Cleaning Platen Cleaning and Replacement Maintenance Cleaning Other Printer Maintenance Replacing the Printhead Maintenance Replacing the Printhead Maintenance Replacing the Printhead Replacing the Printhead Post Maintenance Replacing the Printhead Troubleshooting Status Light Error Resolutions Status Light DescriptionsPrinter is receiving data Printhead is over temperaturePrinthead needs to cool down Media is outNo print on the label Print Quality ProblemsPrinted image does not look right Programmer’s Guide Is the printer in pause mode? If so, press the Feed button Manual Calibration Printing a Configuration Label Troubleshooting TestsRecalibration Resetting the Factory Default Values Communications DiagnosticsTroubleshooting Communications Diagnostics Feed Button Modes Flash Sequence ActionPower On Modes Appendix Universal Serial Bus USB Interface Parallel Interface Ieee 1284-AEthernet Interface Serial Port Interface Pin DescriptionConnecting the Printer to a DTE Device

GX420t, GX430t specifications

Zebra Technologies has established itself as a leader in the printing solutions market, especially with the introduction of its GX series of thermal printers. Among the most notable models are the GX430t and GX420t, both widely recognized for their reliability, versatility, and advanced features.

The GX430t printer boasts a high-resolution printing capability of up to 300 dpi, making it ideal for applications where clarity and detail are paramount. This makes the printer particularly useful for producing labels that require intricate graphics and small text. On the other hand, the GX420t provides a resolution of 203 dpi, which is still impressive for standard label printing applications. Both models support a range of media types, including labels, tags, and wristbands, making them adaptable to various industries such as healthcare, retail, and manufacturing.

One of the standout features of the GX series is their ease of use. Both models incorporate a straightforward, user-friendly interface with a large graphic LCD display that simplifies operation and configuration. The printers are designed for quick setup and maintenance, with features like a clamshell design that allows for fast media loading. Additionally, both models come with USB and serial connectivity options, ensuring compatibility with a wide range of systems.

Both the GX430t and GX420t utilize thermal transfer and direct thermal printing technologies, offering flexibility depending on the application's requirements. The thermal transfer method enables the use of different ribbon types and materials, facilitating high-quality prints that are durable and smudge-proof. This is particularly important in environments where labels face wear and tear.

Another significant characteristic is their compact size, which makes them suitable for both desktop and mobile use. The GX series printers are designed for speed, with print speeds of up to 4 inches per second for the GX420t and slightly higher for the GX430t, enhancing productivity in busy environments.

Moreover, Zebra Technologies ensures that these printers are equipped with advanced management and monitoring capabilities. The ZebraSetup Utilities enable easy configuration, and the printer's status can be monitored in real-time, minimizing downtime and ensuring smooth operation.

In conclusion, the Zebra Technologies GX430t and GX420t printers stand out in the market due to their high-resolution printing capabilities, ease of use, and robust connectivity options. Their range of features makes them ideal for various industries, where reliable and high-quality label printing is essential. As businesses continue to seek efficient solutions for their labeling needs, these models provide a reliable choice, ensuring quality and performance as top priorities.
Top Page Image Contents