American Dynamics specifications Applying Power, Assigning the KT-PC4204 module

KT-PC4204

4 Relay Output and Power Supply

3.4. Applying Power

After all wiring is completed, apply power to the KT-300. Connect the battery leads to the battery, then connect the AC transformer. Then, connect power to the KT-PC4204: the battery leads followed by the AC transformer.

Note: Do not connect the power until all wiring is complete.

4.Assigning the KT-PC4204 module

Once all wiring is complete, the module must be assigned to the system. To assign the module, perform the following steps:

1.Establish communication between the PC and the controller,

2.Remove the tamper switch wire (or only the wire if tamper switch is not used),

3.A serial number should be displayed on the screen, in the same window where is the serial number appears, you should see the type of module and on which controller it is connected,

4.From the software, select the functionality of the module and enter the serial number in the appropriate field (see your software reference manual under controller definition -- Assigning modules for more details),

5.If the module is used in “repower” mode, assign an “all valid” schedule to relay 1 and assign the module’s functionality to “relay 1 to 4” in your software.

Note: Don’t forget to reconnect the tamper switch (or the wire, if there is no tamper switch).

Note: If the module is uses as a “repower” module, ensure that Jumper J1 is set to “Combus Relay” position.

Terminal Connections

Module no.: ______________________________________________________________________________________

Date of installation: _______________________________________________________________________________

KT-300 Name: ____________________________________________________________________________________

KT-300 SITE NAME: _______________________________________________________________________________

KT-300 Serial Number: _____________________________________________________________________________

AUX: ___________________________________________________________________________________________

COMBUS (FROM):_________________________________________________________________________________

COMBUS (TO): ___________________________________________________________________________________

Repower: YES:  (if yes, assign an “All valid” schedule to Relay 1) NO: 

RLY1: Normally open (NO): ________________________________________________________________________

Normally closed (NC): _______________________________________________________________________

RLY2: Normally open (NO): ________________________________________________________________________

Normally closed (NC): _______________________________________________________________________

RLY3: Normally open (NO): ________________________________________________________________________

Normally closed (NC): _______________________________________________________________________

RLY4: Normally open (NO): ________________________________________________________________________

Normally closed (NC): _______________________________________________________________________

FCC & IC COMPLIANCE STATEMENT

CAUTION: Changes or modifications not expressly approved by Kantech Systems Inc. could void your authority to use this equipment.

This equipment generates and uses radio frequency energy and if not installed and used properly, in strict accordance with the manufacturer’s instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for Class B device in accordance with the specifications in Subpart “B” of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in any residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to television or radio reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Re-orient the receiving antenna

•Relocate the alarm control with respect to the receiver

•Move the alarm control away from the receiver

•Connect the alarm control into a different outlet so that alarm control and receiver are on different circuits.

If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user may find the following booklet prepared by the FCC helpful: “How to Identify and Resolve Radio/Television Interference Problems”. This booklet is available from the U.S. Government Printing Office, Washington, D.C. 20402, Stock # 004-000-00345-4. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation. This class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. The KT-300 is also compliant with EN55022: 1994, amendment 1: 1995, Class B.

Kantech Systems Tel.: 1 (450) 444 2030 • Toll Free: 1 888 222-1560 • Fax: 1 (450) 444 2029 • Internet: www.kantech.com	DN1246-0404
Copyright  2004 Kantech Systems. All rights reserved • Specifications may change without notice.