Antec II Connecting the Power and LED, Connecting the USB Ports, Motherboard Pin Layout

Page 3

CONNECTING THE POWER AND LED

1.Connect the 24-pin or 20-pin ATX power connector and +12V 4-pin connector to your motherboard. Note: an ATX12V v2.0 power supply comes with a 24-pin power connector. This is the latest Intel form factor power supply.

2.Connect the Reset switch (labeled RESET SW) to your motherboard at the RST connector. Make sure the label always faces the front of the case.

3.Power LED (labeled POWER LED) connector is located behind the Reset connector.

4.Power Switch (labeled POWER SW) connects to the PWR connector on the motherboard.

5.Speaker (labeled SPEAKER) connector is behind the PWR connector.

6.Hard Drive LED (labeled HDD) connects to the IDE connector.

7.LED I, LED II connectors: This case comes with two extra LEDs, marked I, II. You may use these LED for various purposes such as SC SI LED, Message LED, etc.

CONNECTING THE USB PORTS

You will find a single 10-pin connector on a cable attached to the front USB ports. This is an Intel standard connector, which is keyed so that it can't be accidently reversed as long as it is connected to a proper Intel standard motherboard header. Connect the 10-pin connector to your motherboard headers so that the blocked pin fits over the missing header pin.

Note: Please check your motherboard manual for your USB header pin layout and make sure it matches the attached table. If it does not match this Intel standard, please call Antec customer service at (800) 22ANTEC (North America) or +31 (0) 10 462-2060 (Europe) to buy a USB adapter. This adapter will allow you to connect the front USB to your motherboard on a pin-by-pin basis.

Motherboard Pin Layout

1

2

 

 

 

 

 

Pin

Signal Names

Pin

Signal Names

 

 

 

 

 

 

 

 

 

 

 

 

 

1

USB Power 1

2

USB Power 2

 

 

 

3

Negative Signal 1

4

Negative Signal 2

 

 

 

 

 

 

 

 

 

 

5

Positive Signal 1

6

Positive Signal 2

 

 

 

7

Ground 1

8

Ground 2

 

 

 

9

Key (No Pin)

10

Empty Pin

9

10

 

 

 

 

 

 

 

 

 

CONNECTING THE IEEE 1394 (FIREWIRE®, I.LINK®) PORT

You will find a single 10-pin connector on a cable attached to the front IEEE 1394 connection. This is an Intel standard connector which is keyed so that it can't be accidentally reversed as long as it is connected to a proper Intel standard motherboard header. Connect the 10-pin connector to your motherboard header so that the blocked pin fits over the missing header pin.

Note: Please check your motherboard manual for your IEEE 1394 header pin layout and make sure it matches the attached table. If you intend to connect the front FireWire port to an IEEE 1394 add-on card that comes with an external-type IEEE 1394 connector, please call Antec customer service at (800) 22ANTEC (North America) or +31 (0) 10 462-2060 (Europe) to buy an adapter. This adapter will allow you to connect the front IEEE 1394 port to the external-type connector.

3

Image 3
Contents Page Disclaimer Setting UPInstalling the Power Supply Installing the MotherboardMotherboard Pin Layout Connecting the Power and LEDConnecting the USB Ports Connecting the Ieee 1394 FIREWIRE, I.LINK PortMotherboard Pin Layout for Front Panel Ieee 1394 Connector Connecting the Audio PortsDevice Installation Front 80mm fan mounts SpecificationsCooling System TriCool FanMaintaining the Washable Air Filter VGA Card CoolingAntec, Inc Antec Europe B.VTechnical Support