15. MAINTENANCE
Cleaning the Body of the laminaor
1.To clean the machine body, dampen a cloth with water only and gently wipe the machine clean.
Removing Adhesive Build Up
1.Remove the film from the laminator.
2.Use a damp (water only) cloth and a rubber gum eraser to remove the adhesive on the silicone rollers.
Note: Rub firmly but do not scrub the rollers vigorously as this may scratch the surface.Do not use sharp metal objects, steel wool, or abrasives, as these may also damage the rollers.
16. TROUBLESHOOTING
Problem | Cause | Solution | |
|
|
| |
|
| a. Plug the power cord into appropriate | |
| a. Power plug is not plugged in. | outlet. | |
Machine will not turn | b. Power switch is in “0” (Off) position. | b. Put the power switch to the “I” (On) | |
on: | c. Tripped circuit breaker. | position. | |
| d. Blown main power fuse. | c. Reset the circuit breaker. | |
|
| d. Replace the fuse. | |
|
|
| |
| a. Emergency switch (es) is (are) | a. Disengage the emergency switch (es). | |
There is power, but the | b. Close the safety cover to active the | ||
engaged. | |||
rollers are not turning | safety switch. | ||
b. Safety cover is not closed. | |||
after the “RUN” button | c. Properly install the paper guide so that | ||
c. Paper guide is not installed correctly. | |||
is pressed: | the micro switch is activated. | ||
d. Blown motor fuse. | |||
| d. Replace the motor fuse. | ||
|
| ||
|
|
| |
The unit is not heating | a. The machine is in “COLD” mode. | a. Switch to “HOT” mode. | |
b. Set temperature is lower than the room | b. Raise the temperature according to the | ||
up: | |||
temperature. | recommended film temperature. | ||
| |||
|
|
| |
Curled lamination: | a. Upward curl. | a. Loosen the top roll film tension. | |
b. Downward curl. | b. Loosen the bottom roll film tension. | ||
| |||
|
|
| |
Unclear lamination: | a. The main roller temperatures are too | a. Raise the roller temperatures and/or | |
low and/or lamination speed is too fast. | lower the lamination speed. | ||
| |||
|
|
|
|
|
|
| RSH | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
| 17. SPECIFICATIONS |
| ||
|
|
|
|
|
| |
|
| Description |
|
|
| |
|
| Power supply | AC 200,220~240V | AC 200,220~240V |
|
|
|
| 50/60Hz | 50/60Hz |
|
| |
|
|
|
| |||
|
| Power consumption | 3300W | 3300W |
|
|
|
| Max laminating width | 1150mm / 45" | 1650mm / 65" |
|
|
|
| Film thickness | 25 ~ 250mic / 1~10mil | 25 ~ 250mic / 1~10mil |
|
|
|
| Max laminating speed | Hot : 3 m/min / 9.8 ft/min | Hot : 3 m/min / 9.8 ft/min |
|
|
|
| Cold : 4 m/min / 13.1 ft/min | Cold : 4 m/min / 13.1 ft/min |
|
| |
|
|
|
| |||
|
| Ready time | 20 min | 40 min |
|
|
|
| Heating method | Hot roller | Hot roller |
|
|
|
| Driving motor | DC geared | DC geared |
|
|
|
| Max. temperature control | 160°C / 320°F | 160°C / 320°F |
|
|
|
| Speed control | 9 settings | 9 settings |
|
|
|
| Transport type | 4 Roller | 4 Roller |
|
|
|
| Film core size | Auto grip (2.25", 3") | Auto grip (2.25", 3") |
|
|
|
| Cooling system | 2 Blower | 3 Blower |
|
|
|
| Side cutter | No | No |
|
|
|
|
|
|
|
| |
|
| Cross cutter | Yes | Yes |
|
|
|
|
|
|
|
| |
|
| Film alignment | No | No |
|
|
|
| Hot lamination | Yes | Yes |
|
|
|
| Cold lamination | Yes | Yes |
|
|
|
| Mounting thickness | 15mm / 0.6" | 15mm / 0.6" |
|
|
|
| Take up system | chain link to main motor | chain link to main motor |
|
|
|
| Paper counter | Option | Option |
|
|
|
| Length measurement | Option | Option |
|
|
|
| Reverse | Yes | Yes |
|
|
|
| Remote control | Yes | Yes |
|
|
|
| Foot pedal | Yes | Yes |
|
|
|
| Unit dimensions | 1500 x 650 x 1210 (mm) | 1960 x 650 x 1210 (mm) |
|
|
|
| (w x d x h) | 59" x 25.5" x 47.5" | 77" x 25.5" x 47.5" |
| |
|
| Unit weight | 169kg / 373lbs | 269kg / 593lbs |
|
|
|
| Carton dimensions | 1660 x 900 x 1460 (mm) | 2190 x 900 x 1460 (mm) |
|
|
|
| (w x d x h) | 65.5" x 35.5" x 57.5" | 86" x 35.5" x 57.5" |
| |
|
| Carton weight | 280kg / 618lbs | 394kg / 869lbs |
|
|
17 | 18 |