Orion Car Audio HP-2600, HP-4600, HP-2300, HP-2400 SET UP and Troubleshooting, Testing the System

Page 23

Step 8 Connect power wires to the amplifier (ground first, then 12 V(+) and REM). Do not connect the battery at this time.

Step 9 Connect the RCA and speaker wires to the amplifier. Check the quality of your speakers and signal connections. This will determine the ultimate per- formance of your Orion amplifier. Refer to the Signal Input and Output Level Controls and Speaker Connections sections of this guide for correct wiring instructions.

Step 10 Reconnect the ground terminal to the battery after power, speaker, and RCA connections are completed.

Step 11 Set crossovers. Refer to the Internal Crossover Configuration section of this manual for detailed instructions.

Step 12 Pre-drill amplifier mounting holes. Be sure to "think before you drill". Gas tanks, fuel lines, and other obstructions have a nasty way of hiding them- selves. For best results use a marking pen to mark the mounting holes and pre-drill these holes with a standard 1/8" drill bit.

Step 13 Mount the amplifier. Make sure the amplifier is mounted on a flat surface. If this is not possible, do not over tighten the screws so that the chassis of the amplifier is twisted or bent.

Step 14 install the fuse located near the vehicle's battery and proceed to the Testing the System section of this manual.

WARNING! Never exceed the recommended fuse size of this amplifier. Failure to do so will result in the voiding of your warranty and possible damage to the amplifier.

SET UP AND TROUBLESHOOTING

Testing the System

After you have completed the installation, you need to test the system. This will help ensure years of trouble-free operation. Please refer to the listed steps below when testing the sound of your Orion system.

Step 1 Check all the wiring connections to be sure they are correct and secure.

Step 2 Turn the signal source volume control all the way down. Set any tone con- trols to their flat or defeated positions. This includes the loudness control.

Step 3 Turn the level controls of the amplifier to their minimum positions.

Step 4 Turn the source unit on. Check to see if the power LED located on the con- nection side of the amplifier is on. If not, please refer to the Power Connections and the Troubleshooting Tips sections of this manual for instruc- tions.

Step 5 If using an aftermarket source unit, turn the level controls of the amplifier about one quarter of a turn. Slowly increase the volume level of the source unit to so that you can hear the output of the system. If no sound is heard or if the output is distorted, turn the system off immediately. Refer to the Power Connections and the Troubleshooting Tips sections of this manual to solve your installation problems.

Step 6 Check to make sure the output for each channel is correct. If the active crossovers are used, check to make sure that each output is correct from the amplifier. When using active crossovers on midrange and tweeters, do not use crossover frequencies lower than recommended. If the system is not con- figured properly, refer to the Internal Crossover Configuration section of this manual and take corrective action.

22

© 2005 Directed Electronics, all rights reserved

Page 22 Page 24
Image 23
Page 22 Page 24
Contents HP-2300 HP-2400 HP-2600 HP-4600 Contents What’s in the Box IntroductionPractice Safe Sound HP-2300, HP-2400, HP-2600 Controls Record Your Serial Number and DateEND Panel Layouts HP4600 Controls HP-2300, HP-2400, HP-2600 ConnectionsHP4600 Connections Directed Electronics, all rights reserved CEA Specifications Amplifier Section HP-2300 HP-2400 HP-2600 SpecificationsAmplifier Section HP-4600 Amplifier Settings High-Pass Crossover Adjusting Intelli-BassSealed Example High-Pass Set at 20Hz Infinite Baffle Example High-Pass Set at 30HzRemote Bass Operation optional Sealed Example High-Pass Set at 30HzVented Example High-Pass Set at 30Hz High Level Input Harness Amplifier WiringPower Connections Speaker Connections HP-2300, HP-2400, and HP-2600 One Channel/Two Channel ConfigurationBridge Configuration Three Channel Channel 1, Channel 2, Bridged Speaker Connections HP-4600 Four Channel Stereo ConfigurationThree Channel Stereo/Bridged Configuration Tri-Mode Six Channel Configuration Passenger Compartment Amplifier InstallationGeneral Precautions and Installation Tips Choosing Mounting LocationsTools of the Trade Step By Step InstallationTesting the System SET UP and TroubleshootingAdjusting the Sound of the System Symptom Probable Cause Action To Take Troubleshooting TipsInternal Crossover Configuration Directed Electronics, all rights reserved Directed Electronics, all rights reserved Warranty

HP-2600, HP-2400, HP-2300, HP-4600 specifications

Orion Car Audio has established a renowned reputation in the world of automotive sound systems, and their models HP-2300, HP-2600, HP-2400, and HP-4600 stand as shining examples of their engineering prowess. Each of these amplifiers showcases advanced features and technologies designed to enhance the audio experience for car enthusiasts.

The Orion HP-2300 is a powerful amplifier featuring a compact design that makes it easy to install in various vehicles. This model delivers 2,300 watts of peak power, making it ideal for those who crave deep bass and clear treble. One of its standout characteristics is the patented NCL (Negative Current Limiting) technology, which protects the amplifier from damage due to overheating or overloading. Additionally, it comes equipped with adjustable high-pass and low-pass filters, allowing users to customize audio output according to their preferences.

Next in the lineup is the Orion HP-2600, which is engineered for high performance and exceptional sound clarity. With a peak power output of 2,600 watts, it is designed to drive multiple subwoofers and speakers without distortion. The HP-2600 features remote bass gain control, enabling the user to adjust bass levels on the fly. Its durable construction and advanced cooling mechanism ensure reliability during extended use, while the onboard LED indicators provide real-time monitoring of performance levels.

The HP-2400 model balances power and efficiency, delivering 2,400 watts of peak power. It incorporates MOSFET power supplies, which contribute to greater efficiency and less heat generation compared to traditional amplifiers. Users will appreciate the crossover options that enhance system versatility, allowing for smooth transition between frequencies. This model's variable bass boost feature further enriches the listening experience by enhancing low-end frequencies to provide that extra punch when needed.

Lastly, the Orion HP-4600 is a high-output amplifier capable of 4,600 watts peak power, making it one of the most powerful options in the Orion lineup. This model is perfect for enthusiasts looking to achieve a concert-like experience in their cars. It includes sophisticated Digital Signal Processing (DSP) technology, allowing for fine-tuning of the sound stage and clarity. Its multiple channel configurations provide flexibility for various system setups, ensuring that users can achieve their desired audio output with ease.

In summary, the Orion Car Audio HP-2300, HP-2600, HP-2400, and HP-4600 amplifiers are distinguished by their impressive power output, advanced technologies, and user-friendly features – making them excellent choices for car audio enthusiasts seeking to elevate their listening experience to new heights.
Top Page Image Contents