SATELLITE/SUBWOOFER Phasing Test | MK Sound V-850, V-851 specs

POWERED SUBWOOFER

The best way to set the level of the subwoofer is to do it by ear, listening over several hours or days to familiar recordings. Make adjustments to the level in small increments, depending on whether the bass level sounds too high or too low. Of course, you can always deliberately set the level higher or lower than flat if you need a higher bass level (especially for cinema or television sources) or if you don't want to disturb your neighbors.

5.SATELLITE/SUBWOOFER PHASING TEST

You are now almost finished with the basic set-up. But before you can sit down to enjoy your new subwoofer, you need to perform one simple Phasing Test. This test insures optimum sound in the critical bass frequencies where your subwoofer and satellite speakers overlap.

Play a familiar CD, LP, or tape with steady, consistent bass. Listen carefully to the mid-bass (70 - 100 Hz) region — the part of the spectrum where electric or string basses and drums are found. Then, move the "PHASE" switch on the SUBWOOFER's back panel from either up (+) or down (—) to the opposite position.

Now listen to the same musical passage, concentrating on the mid-bass region. If you hear less bass, the original connections were correct. If you hear more bass, the new connections are correct. If you have two subwoofers, perform one test for each subwoofer. When you perform each test, make sure the other subwoofer is not operating by either unplugging its input cable or its power cord.

Another method of setting phase uses a pink noise source and a spectrum analyzer. If you have these, place the microphone at the main listening position and look at its display in the mid-bass region of 70 - 100 Hz. The wiring/ switch position showing the most output in that region has the correct phase.

You need to perform this test because when satellite speakers are located separate from a subwoofer, each speaker is at a different distance from your ear. In some cases, the difference will be just enough so that the output from the subwoofer arrives out of phase with the output of the satellites. When this happens, that critical mid-bass is actually cancelled. You should re-do this test any time you move your speakers.

If you want to experiment further, you can move the satellite speakers either towards or away from your listening position, making changes in small increments. This will focus the system's sound to its optimum. When you hear the best balance between stereo image localization and maximum impact and output in the mid-bass, you have the ideal location.

6.USE OF THE "LOW PASS FILTER" CONTROL

The back panel control "LOW PASS FILTER" sets the upper rolloff point of the subwoofer, eliminating mid-bass and midrange that are being reproduced by your satellite speakers. The control is a means of fine-tuning the transition between your subwoofer and satellite speakers, and it provides a rolloff of 12 dB/octave up to 125 Hz, where the filter shifts to 36 dB/octave. In most systems, including M&K satellites, 85 Hz gives the best blend. If you don't want to experiment, set the control at 85 Hz.

The goal is to get a balanced acoustic output in your room. This is not necessarily the same as flat electrical output. Rooms typically reinforce bass frequencies around 100 Hz, so by leaving an electrical gap, you may actually get a smooth acoustical response where it matters, in the room.

Think of this control as a mid-bass fine tuning adjustment that you set to achieve the best transition between the satellite speakers and the subwoofer. When you hear a smooth sound overall, well balanced between the deep bass and the rest of the audible spectrum, the control is set properly.

7.USE OF THE "BYPASS" SWITCH (Recommended with Dolby Digital & THX components)

If you have a THX, Dolby Digital, or DTS component with a built-in Low-Pass filter as part of its subwoofer output, or if you are using a separate Electronic Crossover, set the “VARIABLE” / “BYPASS” switch on the back of the subwoofer to “BYPASS” position. This bypasses the internal low-pass filter so that there is no interaction between the subwoofer’s filter and your component’s filter. If you have any questions regarding the filters, please contact your M&K dealer or the M&K factory.

8.USING MULTIPLE SUBWOOFERS

Using two (or more) subwoofers in your system gives you the ultimate in bass performance. You'll hear improved impact and definition, as well as greater output and dynamic range. See Section 4 on page 5 for more information.

V-851, V-850 specifications

MK Sound, a brand renowned for its high-performance audio devices, presents the V-850 and V-851, two impressive subwoofers that elevate the standard for home theater and music listening experiences. Designed with cutting-edge technology and superior craftsmanship, these models promise to deliver deep, impactful bass that enhances any audio setup.

The MK Sound V-850 is a powered subwoofer that features an 8-inch driver, delivering an impressive 150 watts of continuous power with a peak output of 300 watts. This robust power handling enables the V-850 to reproduce low frequencies with exceptional clarity and authority, making it an ideal choice for both movie enthusiasts and music lovers. The subwoofer's frequency response extends down to 30 Hz, ensuring that even the deepest bass notes are rendered accurately, providing a thrilling audio experience.

On the other hand, the MK Sound V-851 steps up with a more powerful configuration, incorporating a larger 10-inch driver that operates with a continuous power of 200 watts and a peak output reaching 400 watts. This additional power and larger driver size allow the V-851 to produce even more profound bass tones while maintaining precision. Its frequency response also reaches down to 25 Hz, ensuring that every rumble from explosions in movies or the deep notes in music is felt as much as it is heard.

Both models come equipped with advanced digital signal processing (DSP) technology, enhancing their performance by managing amplifier distortion and optimizing overall sound quality. The DSP provides users with customizable settings, allowing them to adjust parameters such as crossover frequency. This flexibility makes it easier to integrate these subwoofers seamlessly into any existing audio system, regardless of the brand or configuration.

In terms of build quality, the V-850 and V-851 feature sturdy wooden cabinets that not only enhance the aesthetic appeal of the subwoofers but also reduce unwanted resonances. The front-firing design allows for versatile placement options, ensuring maximum bass output regardless of the room layout.

Moreover, both subwoofers include adjustable phase control and volume settings, giving users fine-tuned control over their audio experience. This feature ensures that the bass complements other speakers in the setup, resulting in a harmonious sound blend.

In summary, the MK Sound V-850 and V-851 subwoofers are engineered for audiophiles who seek robust bass performance and versatility. With their powerful drivers, advanced digital signal processing, and quality craftsmanship, these subwoofers are sure to impress anyone looking to upgrade their audio experience. Whether for movies, gaming, or music, the V-850 and V-851 stand out as top-tier choices in the subwoofer market.