Toshiba TDP-T30 owner manual Basic operations, Turning the power on and off

Turning the power on and off (Continued)

Notes

•The start-up screen will disappear after a moment. You can dismiss the start-up screen before this by performing any operation. You can also configure the start-up screen not to appear via the Display setting menu p.32 .

•The first time you use the projector after purchase, after the start-up screen disappears, the Language menu is displayed p.25 .

■Turning the power off

1Press the ON/STANDBY button.

A message appears on the screen, confirming that you wish to shut off the power. This message will disappear after a moment. (This operation is no longer valid after the message disappears.)

2Press the ON/STANDBY button again.

The screen turns off, but the internal cooling fan continues to operate for a short while. Then, the projector goes into standby mode.

	When cooling lamp			During internal cooling			After cooling complete
	TEMP	FAN		TEMP	FAN		TEMP	FAN
	LAMP			LAMP			LAMP
	(Green)	(Green)		(Off)	(Green)		(Off)	(Off)
Flashing
A	(Orange)		B	(Orange)		C	(Orange)

ADuring cooling, the LAMP indicator flashes. In this state, the power cannot be turned back on.

BAfter the LAMP indicator goes off, the cooling fan continues to operate for a short while, in order to expel excess internal heat. If you are in a hurry, there is no problem with unplugging the power cord or turning off the main power switch in this state.

CIn standby mode

Note

•The projector consumes about 6W of power in standby. We recommend that you unplug the power cord or turn off the main power switch if you will not be using the projector for an extended period.

PRECAUTION

•If the power cord is unplugged before cooling is complete, give the lamp time (about 5 minutes) to cool before plugging it back in. If the lamp overheats, it may fail to light, and its lifetime will be shortened.

Basic operations

1Turn on the power.

Turn on the power by following the instructions in “Turning on the power” p.23 .

2Select the language and the lamp power (When using the first time).

When the projector is used for the first time after purchase, menu for language and

lamp power selection and configuration is displayed in English. (If the screen is out of
focus, adjust it according to the step 6 .)				English
q Use the	or	button to select the
				French
desired language and press the			button.	German
				Italian
Message for setup confirmation is displayed in a
				Spanish
selected language.
				Portuguese
Then, the menu for lamp power selection and				Russian
configuration is displayed. It is automatically set as				Swedish
				Turkish
Standard. To change the setting, follow the step w.
				Japanese
w Using the	or	button, select Standard		Chinese (simplified)
or Low for the lamp power (menu item)				Chinese (traditional)
				Korean
and press the		button.

The lamp power, if selected, will be toggled without pressing the button. The display automatically disappears in a few seconds.

Notes

•When the projector is turned on the next time, the Language and Lamp power menus do not appear upon startup. However, if “Reset all” is executed from the Default setting menu p.33 , the Language and Lamp power menus will be displayed the next time when the power is turned on.

•The language can also be set via the Display setting menu p.32 and Lamp power via the Default setting menu p.33 .

•This owner’s manual assumes that English has been selected.

3Activate the connected device.

Turn on and start the connected device such as a computer.

4Press the INPUT button.

An image of the connected equipment is projected.

Each time you press the INPUT button, it switches to the input of the connected equipment.

Notes

•When [Auto input search] is set to [On] in the default setting menu p.33 , the image of the equipment which is connected and turned on is projected.

•Moving pictures generated with the DVD software for computers may appear unnatural if it is projected with this projector, but it is not a malfunction.

Operations

24 25