Toshiba TLP380, TLP381 owner manual Projector operation control by a computer, Computer

Page 26

Projector operation control by a computer

CONTENTS

You can control the projector by a computer connected with the control cable supplied. 73

Check that the power supplies for the projector and for the computer are off before connecting the cables.

USB

MONITOR COMPUTER IN 1

COMPUTER IN 2

Remove the cover to use the CONTROL connector.

 

OUT ( Y/PB/PR )

 

 

 

 

 

CONTROL

 

 

 

AUDIO

VIDEO IN

To remove the cover, slide it up

 

IN R - AUDIO - L

VIDEO S-VIDEO

 

 

 

 

 

 

while pushing it.

 

 

 

Computer

To CONTROL connector

Be sure to connect in the proper direction.

Control cable (supplied)

To RS-232C port

26

connectionsInstallation and

Note

Do not connect any cable other than the exclusive one supplied.

Image 26
Contents TLP380 TLP380Safety Precautions Moisture Condensation Save Original Packing MaterialsAvoid Volatile Liquid Exemption ClausesVentilation Power SourcesSource of Light Important Safety Instructions Do not place the product vertically AccessoriesObject and Liquid Entry Stack InhibitedSafety Check Damage Requiring ServiceReplacement Parts ServicingDo not look into the arm light while it is lit Do not carry by the camera armDo not move the projector while the arm is still erect Strong light may cause damage to your eyes or sightPower supply cord selection Contents Refer to Names of each part on the main unitExplanation here is only for the model without the document Names of each part on the main unit Menu button Input buttonMonitor OUT connector Control connector 26 73 RS-232C connectorUSB connector Computer in 1 connector 22Names of each part on the remote control Open the cover Install the batteriesLoading batteries Attach the coverRear side Remote control operationFront side Floor-mounted projector placement ViewerSide view Determine the screen size projected on the screenTop view Take off the lens cover Connect the power cordLight Orange Power cord Supplied Insert the other end into a wall outletLift up Lower Projector placement angle adjustmentFoot adjuster Foot adjuster release button Turn clockwise to lift up Turn counterclockwise to lowerCeiling-mounted projector placement Viewer Translucent screenConnecting a computer Computer in 1 connector Connecting a computer Computer in 2 connector Connecting video equipment Connectionsand Projector operation control by a computer ComputerHow to use the output connector Projector turns on and the ON, Lamp and FAN indicators Remote controlIndicators Projection on the screenControl panel Main unit side Turn on the connected equipment and put it in playback modePress Enter to confirm LanguagePress Enter Select the input source by pressing Input repeatedlyPress Input and hold for two seconds Picture of the selected input source is projectedStill picture is recommended for focusing Adjust the picture size by turningFocusing ring Zooming leverPress the button to decrease volume Press VOL/ADJ +/- to adjust volumePress the + button to increase volume Press ON/STANDBY again Turning the power offPress ON/STANDBY after using the projector Control panelSource computer and project the image Adjusting the picture automaticallyInput full screen video signals from the input Press Auto SETConfirm the keystone distortion Correcting the keystone distortionPress Keystone Repeatedly until the menu disappearsKeystone adjustment finishes Press Mute Icon appears in the mute modeCutting off the picture and sound temporarily Sound and picture are cut off temporarilyFreezing the picture Press FreezePress Resize Icon appears in the resize modeEnlarging the picture size Sub-picture is displayed Displaying PIP Sub-picturesPress PIP Displaying Information Press CallDirection in which you want to move Point the remote control at the remote controlTo move the pointer Pointer. The speed at which the pointer movesOperating the menu screen Press MenuStart Guide Menu adjustments and settings ShutterFull Menu adjustments and settings Picture ResetFull Menu adjustments Position Full Menu adjustments Color Full Menu adjustments and settings Audio Full Menu adjustments and settings Display Settings AdjustmentsFull Menu settings Default setting Full Menu settings Reset Reset allPIP menu setting Page Preparation of the document imaging camera ImagingDocument cameraCamera head over them Press ARM LightSet a document to be projected Press Camera to select the camera input mode Focusing ringCamera subject which is too dark or vivid When finished, turn off the light and close itPress Camera Gain +/- to improve view of a Put back the armOverlaying projection Project a white paper and enlarge it to fill Press W.BALANCE to turn the Lock indicatorLocking the white balance ScreenCover the camera lens with a piece of black Correcting illuminated defectsWith the document camera operating, fully Paper or clothTrouble indications Main unit sideClean the air filter Air filter cleaningUnplug the power cord Take off the air filter cover Detach the air filterAir filter Air filter cover Assemble the air filterMount the air filter cover Cleaning the main unit Lens and main unit cleaningCleaning the lens Replacing the intake, exhaust fans and air filterTake off the lamp cover on the bottom panel Lamp replacementUnplug the power cord Wait until the lamp gets cool enough Pull out the lampAttach the lamp cover Reset the lamp timerLoad a new lamp Slide the cover into place and tighten the two screwsBefore calling service personal Symptom Cause CorrectionBefore calling service personal Mini D-sub 15pin Connector Do not connect anythingTiming chart Applicable signalSignal Timing Horizontal Signal Timing Vertical Applicable signal Compatible Video and S-Video signalControlling the projector by using RS-232C Signal assignment of RS-232C Interface formatControlling the projector by using RS-232C VCL MO0 MS0 PIP Specifications Main unitSpecifications Replacement lamp

TLP381, TLP380 specifications

The Toshiba TLP380 and TLP381 are advanced optoisolators designed for various applications requiring reliable isolation and switching control. These devices are particularly valuable in communication, industrial, and consumer electronics, where signal integrity and noise immunity are crucial.

The TLP380 is a phototransistor optoisolator, featuring a gallium arsenide infrared LED and a phototransistor. With a minimum isolation voltage of 5,000 VRMS, it provides high voltage isolation between input and output, making it an excellent choice for protecting sensitive components from high voltages and surges. The TLP380 offers a high-speed switching capability, with a rise time of around 4 μs, enabling it to transmit signals efficiently in digital circuits.

On the other hand, the TLP381 is also a phototransistor optoisolator but specifically optimized for lower input current, making it more power-efficient. It offers similar isolation voltage ratings and switching characteristics to the TLP380, but with a lower input current threshold, which can be particularly advantageous in battery-powered applications. The lower current requirement helps extend battery life and minimizes power consumption in portable devices.

Both TLP380 and TLP381 devices feature a wide temperature range, making them suitable for various environmental conditions. Their operating temperature ranges from -40°C to +100°C, ensuring reliable performance under extreme conditions. Additionally, with their compact DIP packages, they are easy to integrate into crowded PCB layouts, making them a preferred choice for designers targeting space-constrained applications.

In terms of characteristics, both models provide low output voltage saturation and high-speed operation, which are critical in achieving fast response times in control circuits. The combination of robust isolation, efficient power consumption, and temperature stability makes the TLP380 and TLP381 versatile solutions for isolating signals in a myriad of electronic systems.

In summary, the Toshiba TLP380 and TLP381 optoisolators are engineered for high-performance signal isolation, offering superior technologies and characteristics that cater to a range of applications. Their reliability, efficiency, and compact design make them a compelling choice for engineers and designers looking to enhance their electronic systems.