Toshiba GX7 Series manual Meets or Exceeds Your Specifications

Meets or Exceeds Your Specifications

GX7 Specifications

Standard Specifications

Item
Voltage Class		600 VAC
Maximum HP	500 HP	600 HP	700 HP	800 HP
Drive Rating (A)	481 A	601 A	698 A	770 A
Dimensions		95”H x 32”W x 30.5”D
		Power Requirements
Output Frequency	0 to 299 Hz
Control Power	DC Bus Control Power
Tolerance	Voltage: ±10%; Frequency: ±2%
		Control Specifications
Control Method	Sine Wave PWM System; Flux Field Current Vector Control
V/Hz Control	Constant Torque, Variable Torque, Open-Loop Vector, Auto or Manual Torque Boost, 5-Point V/Hz Custom Curves
Overload Rating	130% for 120 Seconds; 110% Continuous
Frequency Setting	Rotary Encoder Integrated into EOI, 0 to 10 V, ±10 V, 4 to 20 mA, Binary Input, Motorized Potentiometer Input
Frequency Precision	Analog Input: ±0.2% of Maximum Output Frequency; Digital Input: ±0.01% of Maximum Output Frequency
Frequency Resolution	Panel Operation: 0.01 Hz; Analog Input 10 to 12-Bit A to D Converter: 0.1 Hz
Acceleration / Deceleration	0.1 to 6000 Seconds
Speed Regulation	Up to 0.1%; 60:1 Speed Range
Torque Setting	±250% of the Rated Torque
Set Point Control (PID)	Proportional Gain, Integral Gain, Feedback Settings Upper/Lower Deviation Limits, Feedback Source Delay Filter, Feedback Settings
	Differential Gain
Analog Inputs	Four Programmable: (1) 4 to 20 mA, (1) 0 to 10 V, (1) -10 to +10 V, (1) 1 to 10kΩ Potentiometer Connection
Analog Outputs	Two Programmable to 31 Functions
Discrete Inputs	Eight Programmable to 67 Functions; Expandable to N-Value
Output Contacts	Three Output Terminals, Programmable to 52 Functions; Form C Contacts Rated 250 V AC, Two Amps Inductive
Signal Isolation	Available Three-Channel Signal Isolation for AM/FM Outputs and II Terminal Input, Rated at 750 V
Power Terminals	Input (L1, L2, L3) Output (T1, T2, T3) DCL (PO, PA), DBR (PA, PB), DCBUS (PA, PC)
Control Board	RS232/485 and TTL Ports Standard
Communication Ports
Data Transmission	Profibus, DeviceNet, Modbus RTU, Modbus+, Metasys, Ethernet (Some Devices are External)
Main Protective	Current Limit, Overcurrent, Overvoltage, Undervoltage, Load-Side Short Circuit, Load-Side Ground Fault, Armature Short; Overtorque,
Functions	ASD Overload, Motor Overload, Heatsink Overheat, Open Output Phase, Loss of Feedback, CPU Error, Communications Error
Soft Stall	Automatic Load Reduction Control During Overload
Retry	Can Automatically Clear Fault Upon Trip; Programmable to 10 Tries with up to 10 Seconds Between Tries
Restart	Restart into a Rotating Motor
		Interface
LCD/EOI (Liquid Crystal	Backlit LCD Display; Ability to Display Multiple Parameters on One Screen; Keypad may be Operated from External Power Source;
Display/Electronic
	Software is Flash Upgradeable; Includes Multi-Function Rotary Encoder
Operator Interface)
LED Indicators	Run (Red)/Stop (Green), Remote/Local (Green), DC Bus Charge Indication (Red)
Keys	Local/Remote, Monitor/Program, Run, Enter, ESC, Stop/Reset, Up, Down
Monitoring	Main Display Shows Two Monitored Items Continuously, or Scrolls Up to 40 Items
Selectable Display Units	User-Selectable and Configurable along with Scaling Factor Multiplier; Voltage Display Selectable: Volts or %;
	Current Display Selectable: Amps or %.
EOI Communication Ports	RS232/485 and TTL Ports Standard
Remote-Mount Display	Remote Mountable Up to 1000 Feet
		Construction
Enclosure	NEMA 1, IP20, Gasketed and Filtered
Panel Construction	Free-Standing, Front-Maintenance Type, Top or Bottom Access for Motor and Power Cables
Cooling	Forced-Air Cooled Top-Mounted Fans may be Removed During Shipment or Installation
Color	ANSI-61 Gray
		Ambient Conditions
Ambient Temperature	-10 to 40°C (-14 to 104°F)
Humidity	Max. 95% (Non-Condensing)
Altitude	1000 Meters (3300 Feet) Above Sea Level or Less
Installation	Indoor, No Direct Sunlight, Protect from Corrosive Gases and/or Explosive Gases
		Standards

Electrical Compliance

NEC, ANSI