Initial UPS Startup, FAQ Sheet | Toshiba 1600 XP UPS guide

Initial UPS Startup

The first time the UPS is activated after being shipped from the factory, an initialization program will require the operator to input the following parameters. The UPS display operation is explained in detail on pages 32-62

1.The first screen during the initial startup sequence requires the operator to select the nominal input voltage.

Select from 208V, 230V, or 240V, and press the Write key. If the command has been accepted, the word “Successful” will appear at the bottom left side of the display.

2.Repeat the process in step 1 in selecting the Rated Vout.

3.Repeat the process in step 1 in selecting the Input Frequency.

4.Use the keypad to type in the current date in the format: Mon 10/05/2009. and press Write.

5.Use the keypad to type in the current time in 12 hour format: 12:15 PM and press Write.

6.The Main screen is now displayed. Verify the UPS is in BYPASS mode. The mode (lower right side of the display) should display Bypass. If it does not display Bypass, press and momentarily hold the STOP button.

7.With the UPS in bypass mode, cycle power to the UPS as follows:

•At the rear of the UPS switch the main circuit breaker MCCB to OFF.

•Leave the UPS off until the DC bus is safely discharged (approximately 5-10 minutes).

•Restart the UPS by switching the main circuit breaker ON.

The table below summarizes the initialization parameters:

ID	Command	Options
111	Rated Vin	Select from 208V, 230V, or 240V, and press Write.
215	Rated Vout	Select from 208V, 230V, or 240V, and press Write.
141	Input Frequency	Select from 60Hz or 50Hz, and press Write.
634	UPS Date	Input the date in this format: Mon 10/05/2009. and press Write.
635	UPS Time	Input the current time in 12 hour format: 12:15 PM and press Write.

FAQ Sheet

Following are some Frequently Asked Questions concerning installation of the 1600EP Series UPS.

NOTICE

The batteries for the UPS must be installed while the UPS is energized.

FAQ #1 My Output is ~85V.

Problem: Output is wired across the incorrect output terminals. The voltage across terminals 5 – 6(X2 – N) will be approximately 85V.

Solution: The correct 120V output terminals are 4 – 6 (X1 – N), and 7 – 6 (X3 – N).

FAQ #2 My Output is other than 85, 120, 208 or 240V.

Problem: The Terminal strip jumper may be installed incorrectly for the incoming voltage.

Solution: Check that the Jumper wire/buss strip is installed correctly for the incoming voltage.

Toshiba Contact Information: Toshiba Industrial Division, 13131 West Little York Road, Houston, TX 77041

Tel: US 800-231-1412, Canada 800-872-2192, Mexico 01/800/527-1204		www.toshiba.com/ind

4 4		1600XP Series Quick Installation Guide

1600 XP UPS specifications

The Toshiba 1600 XP Uninterruptible Power Supply (UPS) is designed to provide robust backup power and exceptional electrical protection for critical equipment in various applications, including data centers, telecommunications, and industrial settings. This model is geared toward ensuring high reliability in power management, safeguarding against power disturbances that could jeopardize operational continuity.

One of the significant features of the Toshiba 1600 XP UPS is its high efficiency rating. Operating at up to 94% efficiency, it minimizes energy consumption and reduces overall operating costs. This efficiency also contributes to lower heat generation, which helps maintain optimal operating conditions and prolongs the lifespan of both the UPS and connected equipment.

The 1600 XP utilizes advanced double conversion online technology, which provides clean and stable power by continuously regulating voltage and frequency. This technology keeps connected loads free from surges, sags, and transients, ensuring that sensitive electronics operate without complications even in the event of a power failure.

This UPS model is equipped with a modular design, allowing for easy scalability and maintenance. As power demands grow, users can expand the system seamlessly by adding additional modules. Furthermore, the modular architecture simplifies maintenance, as components can be replaced without needing to power down the entire system.

The Toshiba 1600 XP also includes user-friendly features such as an intuitive LCD display, which provides real-time information on UPS status, power consumption, and battery health. Alarm notifications and event logging capabilities further enhance monitoring and management, enabling proactive maintenance and swift response to any issues.

Another characteristic of the Toshiba 1600 XP is its extensive battery management system. This feature extends battery life through smart charging cycles and temperature compensation, ensuring reliable backup power when it's most needed. Additionally, the UPS can be integrated with advanced communication protocols, allowing seamless interaction with building management systems for centralized monitoring.

In summary, the Toshiba 1600 XP UPS is a reliable and efficient power protection solution that combines advanced technology with user-friendly features, making it an ideal choice for industries needing uninterrupted power supply. With its modular design, high efficiency, and robust protection capabilities, it stands out as a valuable asset for maintaining operational integrity in today’s power-sensitive environments.