Kustom WAV 210 owner manual Editing the Digital Effects

Editing the Digital Effects

The presets contain valid parameters under any condition. This makes Programming and Editing the same function. The word “Edit” will describe both programing and editing

EXAMPLE

The Reverb Group of Favorites 1 Rhythm channel preset is being edited.

Rotate to change Reverb Level

functions.

The parameters of the 3 presets stored in the active Favorite bank can be edited while in the Edit mode. This allows you to hear your changes and compare them between channel selections before saving. The active Favorite button and one of the group buttons will flash while in the edit mode. The effect group button lit or flashing indicates the Level can be adjusted. Notice there is also a red rectangle around the effect group name to the left of the level on the VFD display.

How to edit the Digital Effects:

Selecting different effects

To avoid repeating steps during an Edit, press SAVE every time you achieve desirable results.

DIGITAL EFFECTS

FAVORITES GROUP LEVEL

1	2	DEL
SAVE		MOD
3	4	REV	PUSH ON

Press REV button to select next effect in Reverb Group. Hold to scroll through.

For example,

The current effect for the Reverb Group is HALL 1.

Looking at chart Fig. C, HALL 1 is first effect in the group. If you want to select ROOM 1 (the fourth effect in the group), you would press REV button 3 times or hold it to scroll up to the ROOM 1 effect.

Current group levels

Illuminated red rectangle Indicates Reverb Group is being edited.

Press any of the Effect Group buttons. They flash indicating you are in edit mode but no changes are made, even when the illuminated group button is pressed. An illuminated or flashing effect Group button indicates it is selected.

Select any of the 15 effects in a selected group or bypass it by repeat pressing the group button. The effect

name is indicated on the display. The word “” on the display indicates the effect group is turned off. Each time you press a flashing group button, the effect in that group moves up to the next one. You can also hold down the button to scroll through the effects. If you pass up the effect you want, continue scrolling until you reach the effect again. The chart in Fig. C shows how the effects in the 3 groups are organized.

Change the level of an effect group

The selected effect group button is illuminated. Rotate the Level control to raise or lower the level of the

selected effect group. The effect group levels () are indicated on the display to the right of the group name. A red illuminated rectangle around a group name indicates it can be adjusted using the Level control.

Making temporary changes

Once you get your effects set up, you may not want to make permanent changes during a performance.

As long as you stay on the same Favorites bank and not disrupt the AC power, you can make temporary changes without saving. This makes it easy to change settings for different room acoustics.

Saving the temporary changes

Press the Save button. All 3 presets in the selected Favorites bank are saved.

Delete temporary changes and use saved Presets Method 1

Select a different Favorites Bank without pressing save. The temporary changes are lost and originals restored the next time the un-saved Favorite Bank is selected.

Method 2

Turn power off then on again. Any changes not saved before turning off power will be lost.

Fig. C

Effect group selections

	DELAY		MODULATION				REVERB
Type	Variation	Display Name	Type	Variation	Display Name	Type	Variation	Display Name
Not Active		BYPASS	Not Active		BYPASS	Not Active		BYPASS
Single Short Delay	50ms	50 ms	Chorus	Light Depth 1	Chor 1	Hall 1	1s	HalL 1
Single Medium Delay	100ms	100 ms	Chorus	Light Depth 2	Chor 2	Hall 1	3s	HalL 2
Single Medium Delay	200ms	200 ms	Chorus	Hi Depth 1	Chor 3	Hall 1	5s	HalL 3
Single Medium Delay	250ms	250 ms	Chorus	Hi Depth 2	Chor 4	Room	.5s	ROOM 1
Single Medium Delay	300ms	300 ms	T remolo	Slow	TREMO 1	Room	1s	ROOM 2
Single Medium Delay	350ms	350 ms	T remolo	Fast	TREMO 2	Room	2s	Room 3
Single Medium Delay	400ms	400 ms	Chorus	Fast 2	FST Chor	Room	4s	ROOM 4
Multi T ap Delay	T riplet	Triple 1	Leslie	Slow	Leslie S	Room Hi Damp	3s	ROOM 5
Multi T ap Delay	T riplet Pan	Triple 2	Leslie	Fast	Leslie F	Hall 2	6s	HalL 4
Multi T ap Delay	4/4 T ime 1	4/4 1	Flanger	Light 1	Flange 1	Hall 2	10s	HalL 5
Multi T ap Delay	4/4 T ime pan 1	4/4 2	Flanger	Light 2	Flange 2	L to R Gate	Hi Dens. 500ms	L-R Gate
Multi T ap Delay	4/4 T ime 2	4/4 3	Flanger	Deep Stereo	Flange 3	Reverse Gate	Lo Dens. 100ms	Rev Low
Multi T ap Delay	4/4 T ime Pan 2	4/4 3	Pitch Shifter 1	Doubler	Doubler	Reverse Gate	Hi Dens. 300ms	Rev High
Regen 40% Delay	100ms	Regen 1	Pitch Shifter 1	Light Detune	L Detune	Forward Gate	Lo Dens. 100ms	Fwd Low
Regen 40% Delay	200ms	Regen 2	Pitch Shifter 1	Deep Detune	D Detune	Forward Gate	Hi Dens. 300ms	Fwd High

11