Toshiba MR-3022, MR-3018 service manual Adjustment

Page 83

[B] Adjustment

Simplex copying:

(1)Turn the power ON while pressing [0] and [5] simultaneously, key in [365]*1 / [3044] *2 and then press the [START] button.

*1 : For e-STUDIO352/353/452/453 e-STUDIO281c/351c/451c, e-STUDIO2500c/3500c/3510c, e-STUDIO2330C/2820C/2830C/3520C/3530C/4520C, e-STUDIO202L/203L/232/233/282/283, e-STUDIO205L/255/305/355/455

*2 : For e-STUDIO2040C/2540C/3040C/3540C/4540C, e-STUDIO206L/256/306/356/456

(2)Enter the value.

•If the leading edge (F) margin of the copy image is larger than the (E) margin of the chart, enter a value smaller than the current one.

Note:

Changing one value shifts the copy image by 0.1 mm.

•If the leading edge (F) margin of the copy image is smaller than the (E) margin of the chart, enter a value larger than the current one.

Note:

Changing one value shifts the copy image by 0.1 mm.

(3)Press the [ENTER] *1/ [OK] *2 button.

*1 : For e-STUDIO352/353/452/453 e-STUDIO281c/351c/451c, e-STUDIO2500c/3500c/3510c, e-STUDIO2330C/2820C/2830C/3520C/3530C/4520C, e-STUDIO202L/203L/232/233/282/283, e-STUDIO205L/255/305/355/455

*2 : For e-STUDIO2040C/2540C/3040C/3540C/4540C, e-STUDIO206L/256/306/356/456

Duplex copying:

(1)Turn the power ON while pressing [0] and [5] simultaneously, key in [366] *1 / [3045] *2 and then press the [START] button.

*1 : For e-STUDIO352/353/452/453 e-STUDIO281c/351c/451c, e-STUDIO2500c/3500c/3510c, e-STUDIO2330C/2820C/2830C/3520C/3530C/4520C, e-STUDIO202L/203L/232/233/282/283, e-STUDIO205L/255/305/355/455

*2 : For e-STUDIO2040C/2540C/3040C/3540C/4540C, e-STUDIO206L/256/306/356/456

© 2005 - 2011 TOSHIBA TEC CORPORATION All rights reserved	MR-3018/3020/3021/3022
	ADJUSTMENT

5 - 13

5

11/12

Image 83

Contents MR-3018/3020/3021/3022 11/12 Trademarks11/12 Page Contents Rewriting ROM Firmware Updating Circuit Diagram / Harness DiagramMR-3018/3020 MR-3021/3022 SpecificationsSpecifications 06/09 Main ComponentsLocation Components Sectional View S8S4 S10 Electric Parts LayoutS12 S11 S7 S6 S5Solenoid Symbols and Functions of Various ComponentsSensors and Switches MotorsDiagram of Signal Blocks Description of Interface Signals Read motor drive section OutlineFeed motor drive section Original feed motor drive section Intermediate transfer roller Read motor drive sectionExit/reverse roller Original exit/reverse motor drive sectionGate solenoid Reverse flap Exit/reverse motor ReverseOriginal width size Original Size DetectionOriginal tray width sensor = high level Open = low level ShortA4 series width sizes mixed at B5-R standard A4 series width sizes mixed at A3 / A4 standardA4 series width sizes mixed at B4 / B5 standard A4 series width sizes mixed at A4-R standardLT series width sizes mixed at LG / LT-R standard LT series ORG-SRSLT series width sizes mixed at LD / LT standard Jam Power on Standby Radf jam accessCover OPEN? All sensors OFF? Empty sensor ON?Registration roller rotates. Feed motor rotates reverse OriginalCertain period Time passed? Read motor rotatesSent level High Scanning start signalCertain period Duplex?Read motor stops Certain period Time passed? Original exit/reverse Sensor ON?Jam Read sensor OFF? Certain period Time passed?Gate solenoid on Scanning start signal sent level Low Scanning completedRead motor and exit/reverse motor rotate at requested speed Transport request Signal received?Jam Original exit/reverse motor and read motor stop Sensor OFF? Exposure and scanning start OriginalScanning completed Jam Original exit/reverse Sensor OFF? Original exit/reverse motor and read motor stopOriginal intermediate Transport sensor ON? Drive Circuit for Feed Motor Description of CircuitDrive Circuit for Read Motor Drive Circuit for FAN Motor Drive Circuit for Exit MotorDrive Circuit for Pickup Solenoid Reset CircuitDrive Circuit for Gate Solenoid Front cover CoverFront cover Pin Jam access coverRear cover Rear coverLeft cover Take off the jam access cover by sliding itRemove 1 screw and the hinge pin Left coverOriginal tray Original reverse tray Original reverse trayTake off the paper feeder unit RollerPaper feeder unit Remove 1 clip and slide 2 bushingsClip Pickup roller Pickup roller PMFeed roller PM ShaftShaft Slide the pulley and remove 1 pinPull out the shaft and take off the feed roller PulleySeparation roller PM Stay Take off the jam access guideFeeder lower guide Exit/reverse roller Registration rollerExit/reverse roller Exit guidePre-reading guide Pre-reading guideIntermediate transport roller Hinge pinScrew Bushing ConnectorPre-reading roller Post-reading rollerPlaten guide Flange Bearing BushingBushing HolderRing Reverse registration rollerUpper guide Post-reading rollerRoller Open the RADF. Take off the reverse regis- tration rollerRead motor Motor / Motor drive sectionFan motor M4 Read motor M2Harness clamp Read motor drive sectionSpring SpringScrew Tensioner Ring Remove 3 screws and then take off the bracketTake off 1 timing belt and 4 bushings Timing beltOriginal feed motor drive section Original feed motor M109/01 Take off the timing belt, bushings and pulleyRing Bushing Bracket White Black RedSection Disconnect 1 connector from the Radf conOriginal exit/reverse motor M3 Original feed motor driveBracket SolenoidOriginal pickup solenoid SOL1 Original pickup solenoidGate solenoid Gate solenoid SOL2Mark-off line Original tray width sensor S2 Sensor/switchOriginal tray sensor Original tray sensor S1Release 2 latches and take off the original tray sensor Metal plate cover Jam access cover sensor S11Jam access cover sensor Original empty sensor S3Original empty sensor Original length detection sensor Remove 2 screws and take off the bracketOriginal length detection sensor S4 Original width detection sensor-2 S7 Original registration sensor S5Take off the feeder lower guide Feeder lower guide Original width detection sensor-1 S6Original exit/reverse sensor S10 Read sensor S9Take off the pre-reading upper guide Pre-reading guide Original intermediate transport sensor S8Original exit/reverse sensor Disconnect 3 terminals. Remove 1 screw Original jam access cover opening/closing switch SW1Take off the original jam access cover Radf opening/closing sensor S12ADF board PC BoardRadf control PC board ADF board Stopper OthersHinge stopper Remove 1 screw and then take off the hingeDisassembly and Assembly Checking Adjustment of PositionAdjustment 05/12 05/12 MR-3021/3022 only Install the right-hand hinge screw at the rearInstall the bracket on the left-hand hinge Side05/12 ~0.5mm 0mm Adjustment of HeightTurn it clockwise Turn it counterclockwise Heightened19 Chart Original Adjustment of SkewAdjustment Simplex copying 05/12 26 Chart Original Adjustment of the Leading Edge PositionAdjustment 11/12 Adjustment of Horizontal Position 11/12 Adjustment of Copy Ratio 11/12 Adjustment of Radf Opening/Closing Sensor Adjustment Troubleshooting for Mechanical Errors TroubleshootingCheck or replace the Radf board Troubleshooting for Electrical ErrorsJam not reaching the read sensor Feed signal reception jamJam Jam not reaching the original registration sensorStop jam at the original exit/reverse sensor Radf jam access cover open jamStop jam at the original registration sensor Stop jam at the read sensor11/04 Radf open jamCover open jam in the read ready status 09/05 Symbols used in the checklist Periodic MaintenanceRewriting ROM Firmware Updating Component side Soldered side Assembly of PC BoardCircuit Diagram2005 2011 Toshiba TEC Corporation All rights reserved 1 MR-3018/3020 Control PC Board CircuitCircuit Diagram / Harness Diagram Circuit Diagram / Harness Diagram Circuit Diagram / Harness Diagram Circuit Diagram / Harness Diagram Circuit Diagram / Harness Diagram 2 MR-3021 11 09/05 09/05 13 09/05 09/05 15 09/05 3 MR-3022 17 09/05 09/05 19 09/05 09/05 21 09/05 Circuit Diagram / Harness Diagram

Related manuals

Manual 104 pages 38.91 Kb