Rear Panel, Speaker OUT | Kustom Wav 1000 specs

Rear Panel

SPEAKER OUT

MODEL wAv 1000

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

ATTENTION

RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR

OFF

FOOTSWITCH

LEFT

RIGHT

LEFT

RIGHT

Line Out

PREAMP

POWER

PREAMP

POWER

SERIAL NUMBER

Out

AMP IN

Out

AMP IN

LEFT

RIGHT

AC FUSE

FUSE: T2A / 250V

CAUTION

ATTENTION

120V

60Hz 160W

DESIGNED IN USA

MADE IN CHINA

CHASSIS SURFACE HOT

SUPERFICE DE CHASSIS CHAUDE

TAB

Power ON/OFF Switch:

Turns AC power on and off.

AC Power Cord Receptacle:

Insert the AC cord (provided) firmly into the AC connector. NOTE: Replace the AC power cord if protective jacket is damaged or ground pin is damaged or removed.

FUSE:

The fuse is located in a housing just below the receptacle. Replace only with same type and size. To remove the fuse, remove AC power cord and pull out on the tab above the fuse symbol located on the fuse carriage. Place the new fuse in the carriage clip and re-insert. NOTE: To prevent an electrical hazard, DO NOT replace fuse without using the fuse carriage. Replace the fuse carriage if lost or damaged before re-inserting the AC power cord.

Speaker Output Jacks:

These jacks are used to connect external speakers to the head. Each channel has 2 jacks wired in parallel that function the same. Never connect a left and right output to a single mono cabinet. This will cause the amp to load itself, overheat, distort and shut down. It is not recommended to load either channel below 4 ohms because it will not produce maximum output and may cause overheating and shutting down.

For best results, connect external speakers using one of the following methods.

One “WAV® 412”cabinet- Connect a speaker cable from one of the left output jacks on the amp to the left input jack on the cabinet. Repeat for the right channel. This puts an 8 ohm load/per channel on the amp. You can add speakers using the other jacks as long as they are not lower than 8 ohms per channel.

Two “WAV® 412”cabinets, wide separation- Connect a speaker cable from one of the LEFT SPEAKER OUT jacks on the amp to the MONO Jack of the WAV® 412 cabinet on the left. Repeat for right channel. You can increase stereo separation by moving the cabinets further apart. This method is recommended when both cabinets are on the floor. This method puts a 4 ohm load on each channel. The remaining two jacks on amplifier should not be used.

Two “WAV® 412”cabinets stacked- Use the method described for connecting one “WAV® 412” cabinet for both cabinets. This is best when stacking the cabinets on top of each other because it maintains Left and Right channel separation inside both cabinets in the stack. This method uses all 4 speaker jacks and requires 4 speaker cables. The amp load is 4 ohms per channel so no additional speakers should be used.

When used with third-party mono cabinets- Because this is a stereo amp, you will need to connect mono cabinets in pairs. NEVER sum the left and right channels into a single Mono cabinet. You can use up to four 16 ohm pairs, two 8 ohm pairs, or one 4 ohm pair of cabinets. The total load should not be less than 4 ohms per channel.

Footswitch Jack:

Plug Footswitch into this connector using the supplied cable. If the cable is lost or damaged, a standard CAT 5 cable can be used. CAT 5 cables can be purchased at your local retail electronic and computer stores.

Left and Right Line Out:

These ¼” mono jacks deliver the signal going to the speakers at an unbalanced line level. The main purpose of these jacks is to deliver line level outputs to external sound reinforcement devices such as powered monitors or speakers. They will not drive external non-powered speakers. To prevent an undesirable feedback oscillation, do not use these jacks on signal processors or effects that will be using the Power Amp Input jacks.

Left and Right Preamp out:

These ¼” mono jacks deliver an unbalanced line level output from the preamp and digital effects. The main purpose of these jacks is to send a signal to the input of third-party signal processors or effects that will be using the Power Amp Input jacks. These jacks do not interrupt signal flow from the preamp to the power amp.

Left and Right Power Amp In:

These ¼” mono jacks allow the left and right power amplifiers to be used with an external line level input. The main purpose of these jacks is to receive the return signal from a third-party signal processor or effect. NOTE: When used, these jacks will interrupt the signal flow from the preamp to the power amp.

Wav 1000 specifications

The Kustom Wav 1000 is a high-performance amplifier renowned for its blend of innovative technology and classic design. Primarily targeted at musicians, the Wav 1000 offers a powerful output alongside versatile features, making it a favorite among guitarists and bassists alike.

At its core, the Wav 1000 delivers an impressive 1000 watts of power, ensuring that it can drive even the largest gigs with ease. The robust power output is matched with cutting-edge circuitry that enhances sound clarity and fidelity, allowing for dynamic range and tonal richness. This combination makes it ideal for both practice sessions and live performances.

One of the standout features of the Kustom Wav 1000 is its built-in Bluetooth capability. Musicians can easily connect their devices to the amplifier, making it easy to play along with tracks or backing music. This wireless feature also allows for hassle-free streaming of audio, thus expanding creative possibilities during rehearsals or performances.

Another notable technology integrated into the Wav 1000 is its digital effects processor. This processor includes a variety of effects such as reverb, delay, and modulation. Musicians can easily dial in the perfect amount of effects to suit their playing style, which opens up a wide array of sounds and textures at their fingertips. The user interface is intuitive, allowing for easy navigation and customization of settings.

The design of the Kustom Wav 1000 is both rugged and stylish. It features a durable cabinet that ensures long-lasting performance while maintaining a professional appearance. The amplifier is also equipped with heavy-duty handles for easy transport, catering to musicians who frequently move between venues.

In terms of connectivity, the Wav 1000 boasts a variety of inputs and outputs, including auxiliary inputs for external devices, headphone jacks for silent practice, and direct outputs for recording or PA systems. This versatility allows musicians to integrate the amplifier seamlessly into their setup, whether in the studio or on stage.

In summary, the Kustom Wav 1000 stands out as a powerful, feature-rich amplifier that meets the demands of modern musicians. With advanced technologies like Bluetooth connectivity, a digital effects processor, and robust construction, it is engineered to deliver exceptional sound quality and versatility. Whether for practice or live performance, the Wav 1000 is positioned as an invaluable tool in a musician's arsenal.