Toshiba MK3017GAP user manual Installation Notes, Placing Hard Drive inside your Computer

Page 5

Installation Notes

ƒThe drive should be mounted carefully on the surface of 0.1mm or less flatness to avoid excessive distortion.

ƒIn order to prevent short-circuit under any circumstances, a space of 0.5mm or more should be kept under the PCB.

ƒSpace should be kept around the drive to avoid any contact with other parts, which may occur due to shock or vibration.

ƒThe temperature of the top cover and the base must always be kept under 60C to maintain the required reliability.

ƒBe sure not to cover the breathing hole to keep the pressure inside the drive at a certain level

ƒDo not apply any force to the top cover, except the screw areas on top cover. Maximum force to the specified area is 2N.

ƒThe drive contains several parts which may be easily damaged by ESD (Electric Static Discharge). Avoid touching the interface connector pins and the surface of PCB. Be sure to use ESD proof wrist strap when handling drive.

ƒThe four mounting screws should be tightened equally with 0.3N-m (3kgf-cm) torque. The depth should be 3.0mm minimum and 3.5mm maximum.

Placing Hard Drive inside your Computer

Determine mounting configuration (the drive can be mounted in either a horizontal or vertical orientation)

Configure drive for system application.

Configure the adapter board for the specific system application (if required).

Install adapter board into an unused PC/AT 16 bit slot (if required).

Install the I/F cable to the system's 44 pin connector port or adapter board. Ensure pin 1 is oriented correctly, (pin 1 on the cable is usually identified by a red or blue strip.)

Set correct drive type in system CMOS

Refer to applicable manuals for software installation instructions.

Important Note: Disconnect power from your computer system before beginning installation.

Figure 2.HDD Mounting Holes

3

Image 5
Contents Inch Hard Disk Drive Contents Introduction MK3017GAP HDD2159 General FeaturesMaster/Slave Settings Setup MK3017GAP HDD2159Placing Hard Drive inside your Computer Installation NotesBacking up Data Files Using the Hard Disk Drive MK3017GAP HDD2159Problem Solution Troubleshooting MK3017GAP HDD2159Specifications MK3017GAP HDD2159 Page Regulatory PhysicalRecommended Cable Characteristics Drive Connectors MK3017GAP HDD2159Interface Connector Drive Interface Signals

MK3017GAP specifications

The Toshiba MK3017GAP is a notable hard disk drive (HDD) that has garnered attention for its impressive storage capacity and advanced technologies. This 2.5-inch HDD is primarily designed for mobile computing environments, making it a preferred choice for many laptop manufacturers and users seeking enhanced performance and reliability.

One of the standout features of the MK3017GAP is its substantial storage capacity of 30GB, which allows users to store a significant amount of data, including documents, applications, music, and multimedia files. This was especially noteworthy during its prime, as it provided an opportunity for users to have more files at their fingertips without resorting to external storage solutions.

The drive operates at a spindle speed of 4200 RPM, which, while not the fastest on the market, offers a balanced approach between performance and power consumption. This speed is adequate for everyday tasks and general computing activities, particularly in battery-powered devices where energy efficiency remains a critical factor.

The MK3017GAP incorporates Toshiba's proprietary technologies designed to enhance data integrity and reliability. One such feature is the Drive Fitness Test capabilities, which allow users to monitor the health and performance of the drive over time. This is crucial for preventing data loss and ensuring that the drive operates smoothly in diverse environments.

Additionally, the MK3017GAP employs an advanced actuator system that contributes to its performance and reliability, ensuring precise tracking of the data written on the storage medium. The use of perpendicular recording technology also elevates its storage efficiency, allowing for improved data density and faster access times.

In terms of connectivity, the MK3017GAP utilizes the IDE (Integrated Drive Electronics) interface, facilitating compatibility with various systems and making it easier to integrate into different laptop configurations.

Furthermore, the drive is designed with low power consumption in mind, which is an essential feature for mobile devices reliant on battery life. This ensures that users can enjoy extended usage without frequent recharges, enhancing the overall user experience.

In summary, the Toshiba MK3017GAP remains a prime example of a well-engineered hard disk drive, combining a substantial storage capacity with reliable performance, innovative technologies, and energy efficiency. Although it may have been outpaced by newer technologies, it laid the groundwork for advances in portable data storage solutions, making it a significant model in Toshiba's storied history in the HDD market.