Dell 1000W, 1920W/1500W manual Settings Description Available Settings Default Setting

Page 37

Table 7. Settings (continued)

Description

Available Settings

Default Setting

 

 

 

Set Date and Time

Set Month, Day, Year, Hours, Minutes, and Seconds

 

 

Date:mm/dd/yyyy

01/01/2009

 

Time: hh:mm:ss

12:00:00

 

NOTE: The date format is dependent on the

 

 

language selection.

 

NOTE: Time is a 24-hour clock.

Control Commands from Serial Port

[Enabled] [Disabled]

Enabled

If Enabled, control commands are accepted through the serial port, USB ports, or option card.

If Disabled, configuration and load control commands are restricted to LCD only.

Output Voltage

[100V] [110V] [120V] [Auto-sensing]

Auto-sensing

 

 

 

 

[200V] [208V]

 

 

 

 

 

[220V] [230V] [240V]

 

 

 

 

Output Frequency

[50Hz] [60Hz] [Auto-sensing]

Auto-sensing

 

 

 

Overload Alarm Level

[10%] [20%] [30%]...[100%]

100%

 

If 100%, the UPS issues an Output Overload alarm

 

 

at load > 100%.

 

 

NOTE: Output Overload Level 1 by default is set to

 

 

100% and is configurable from 10% to 100% in 10%

 

 

increments through the LCD setting menu. This

 

 

allows customers to be alerted before the UPS has

 

 

reached its rated capacity limits.

 

 

 

 

Automatic Start Delay

[Off] [0s] [1s] [2s]...[32767s]

0s

 

See “Configuring Load Segments” on page 41.

 

 

 

 

Automatic on Battery Shutdown

[Off] [0s] [1s] [2s]...[32767s]

Off

 

See “Configuring Load Segments” on page 41.

 

 

 

 

Start on Battery

[Enabled] [Disabled]

Enabled

 

NOTE: Battery start is disabled from the factory and

 

 

remains disabled until the UPS has been powered

 

 

from utility and enters Standby mode. After the

 

 

UPS has been started once from utility, the Start on

 

 

Battery feature is automatically enabled. After this is

 

 

set by the user, it remains set.

 

 

 

 

Operation 37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Users Guide September 2009 S 164201786 Table of Contents Network Transient Protector Dell UPS Management Software RS-232 and USB Communication PortsUPS Status Menu Event Log Menu Testing BatteriesDell Tower UPS IntroductionIntroduction What are You Looking For? Find It Here Finding InformationUPS Output Power Safety WarningsSafety Warnings Inspecting the Equipment InstallationUnpacking the System Unpacking the System100/120V Rear Panel Identifying the UPS Rear Panels120V Rear Panel 120V, 1500W/100V Rear Panel Identifying the UPS Front Panel Removing the UPS Front Cover Connecting the UPS Internal BatteryConnect the internal battery connector see Figure Removing the Battery Connector Cover External Battery Module InstallationInstalling the Battery Connector Cover Typical UPS Installation 120V Model Shown Installing the UPSPower Cord Ratings Minimum Upstream Circuit Breaker Rating UPS Output PowerUPS Initial Startup Rating Australia Optional GB2099 to C13 Connecting the Power Cord Installation UPS Startup and Shutdown OperationStarting the UPS UPS Shutdown Starting the UPS on BatteryControl Button Functions Control Button Sequence Control Panel FunctionsDisplay Functions Changing the LanguageStartup Screen UPS Status Screen LockedBad Battery Detected or Battery Disconnected Battery ModeUPS General Alarms Active Battery Test StatusStandby Mode Status Summary Screens Description Normal ModeBattery Status Screens Description Measurements Event LogControl Screens Description Control ScreensSettings Description Available Settings Default Setting SettingsIdentification Settings Description Available Settings Default Setting Settings Description Available Settings Default Setting Settings Description Available Settings Default Setting Behavior on Overload Retrieving the Event LogControlling Load Segments Through the Display Configuring Load SegmentsConfiguring Automatic Start Delay Configuring Automatic on Battery Shutdown Configuring the UPS for an EBM Configuring Battery SettingsRunning Automatic Battery Tests Configuring Automatic RestartConfiguring Automatic Battery Tests RS-232 and USB Communication Ports Additional UPS FeaturesGND RS-232 Communication Port Pin AssignmentDell Network Management Card Dell Network Management Card OptionalDell UPS Management Software Network Transient ProtectorUPS and Battery Care UPS MaintenanceTransporting the UPS Disconnect the internal battery connector see Figure Testing Batteries When to Replace BatteriesStoring the UPS and Batteries Updating the UPS Firmware Specifications Electrical Output 100/120V Models 230V Models Power Levels Efficiency Normal modeElectrical Input Nominal VoltageOperating Temperature Environmental and SafetyTemperature Relative Humidity Safety ConformanceBattery Runtimes Battery ConfigurationVoltage FusesAccessing Alarms and Conditions TroubleshootingUPS Status Menu Event Log Menu Typical Alarms and ConditionsAction Troubleshooting Silencing the Alarm
Related manuals
Manual 73 pages 19.17 Kb Manual 63 pages 52.12 Kb

1000W, 1920W/1500W, 500W specifications

Dell's power supply units (PSUs) are essential components for Dell servers and workstations, providing reliable power solutions tailored to meet different demands. Among these, the 500W, 1000W, and 1920W/1500W power supplies stand out for their efficiency, performance, and advanced features tailored to various IT environments.

Starting with the 500W power supply, this unit is designed for entry-level servers and workstations. It boasts a compact design that facilitates easy installation in space-constrained scenarios. The 500W PSU operates with a high efficiency rating, contributing to lower energy costs and reduced heat output. It supports the latest energy standards, including 80 PLUS certification, ensuring that customers can rely on it for consistent performance and reliability. This unit is particularly suitable for small to medium businesses looking for cost-effective power solutions for basic applications.

The 1000W power supply represents a step up, featuring dual 12V outputs that provide stable power for more demanding tasks. Designed for mid-range servers and advanced workstations, it balances performance and efficiency, making it ideal for enterprises that require additional processing power for virtualization, data analysis, and high-performance computing tasks. The 1000W PSU includes built-in protections against over-voltage, short circuits, and over-temperature conditions, adding an extra layer of reliability that is crucial for mission-critical operations.

For environments with higher power demands, Dell offers the 1920W/1500W power supply. This robust unit is engineered for high-performance servers and large-scale data centers, where maximum uptime and performance are paramount. The modular design of the 1920W/1500W power supply allows for enhanced cable management, reducing clutter and improving airflow within racks. With an efficiency rating that adheres to 80 PLUS Platinum standards, this PSU not only minimizes energy consumption but also maximizes operational efficiency, making it ideal for organizations looking to optimize their data center environments.

In summary, Dell's 500W, 1000W, and 1920W/1500W power supplies cater to a wide range of computing needs. From entry-level solutions to high-capacity units for demanding environments, Dell ensures that its power supplies provide reliability, efficiency, and performance. As organizations continue to evolve their IT infrastructure, these power supplies remain pivotal in supporting their growth and operational goals.
Top Page Image Contents