D-Link d-link manual Command Buttons, Save

Page 40

40 Web User Guide

NOTE: If SNMPv3 Authentication is to be used for this user, the password must be eight or more alphanumeric characters.

5.If you do not need authentication, go to Step 9.

6.To enable authentication, use the Authentication Protocol pulldown menu to select either MD5 or SHA for the authentication protocol.

7.If you do not need encryption, go to Step 9.

8.To enable encryption, use the Encryption Protocol pulldown menu to select DES for the encryp- tion scheme. Then, enter in the Encryption Key field an encryption code of eight or more alphanu- meric characters.

9.Click Submit.

Command Buttons

The following command buttons are used throughout the Web interface panels for the switch:

Save

Pressing the Save button implements and saves the changes you just made. Some set-

 

tings may require you to reset the system in order for them to take effect.

Refresh

Pressing the Refresh button that appears next to the Apply button in Web interface

 

panels refreshes the data on the panel.

Submit

Pressing the Submit button sends the updated configuration to the switch. Configura-

 

tion changes take effect immediately, but these changes are not retained across a

 

power cycle unless a save is performed.

Image 40
Contents Layer 2 Switch Page Table of Contents Using the Web Interface Traceroute Web User Guide List of Figures Link DES-3226L Front ViewWeb User Guide About This Book Document OrganizationAudience Related DocumentationLink Offices for Registration and Warranty Service FeaturesTrademarks Copyright Statement„ TCP „ MIB-II Safety Cautions Safety InstructionsProduct Overview Web User Guide General Precautions for Rack-Mountable Products Switch Description Protecting Against Electrostatic DischargeTechnical Specifications Specifications DescriptionPerformance Preparing the Site for Installation Installing the HardwareInstalling the D-Link DES-3226L Switch Setting up the Switch Unpacking the SwitchConnecting the Switch to a Power Supply Installing on a Flat Surface Free-standing Switch Connecting Power CableInstalling in a Rack Attaching the BracketsStarting and Configuring the Switch Configuring for In-band ConnectivitySubnet Configuring for Out-Of-Band Connectivity Starting the Switch Initial ConfigurationInitial Configuration Procedure Example SessionDram 64 MB LED Indicators LEDWeb User Guide Software Installation Upgrading the Switch FirmwareSystem Information and System Setup Quick Starting the Networking DeviceCommand Mode Description Privileged Sets the IP address, subnet mask and gateway Systemimage or a configuration file nvramstartup-con Web User Guide Using the Web Interface Configuring for Web AccessWeb Page Layout Web Interface Panel-ExampleConfiguring an Snmp V3 User Profile Starting the Web InterfaceCommand Buttons SaveIgmp Snooping OverviewCLI Examples Example #1 show igmpsnoopingIgmp Snooping Global Configuration and Status Web ExamplesIgmp Snooping Interface Configuration Web User Guide Considerations Configuration ScriptingExample #1 script Example #4 Creating a Configuration Script Example #3 script apply running-config.scrExample #2 script list and script delete Example #6 script validate running-config.scr Example #5 Upload a Configuration ScriptExample #7 Validate another Configuration Script Example #1 show monitor session Port MirroringExample #2 show port all Example #3 show port interface Example #5 Config monitor session 1 modeExample #4 show monitor session Example #6 Config monitor session 1 source interface Specify the source ports and destination portSystem Port Multiple Port Mirroring Persistent Log Files SyslogInterpreting Log Files Example #2 show logging persistent Example #1 show loggingExample #3 show logging traplogs Example #4 logging port configuration Example #5 show logging hostsFollowing web pages are used in the Syslog feature Traceroute Overview TracerouteCLI Example Web User Guide Vlan Configuration Example Virtual LANsVlan example network diagram CLI ExamplesVirtual LANs Graphical User Interface Private Edge VLANsCLI Example Class of Service CoS CoS Queue MappingTraffic Shaping and Rate Limiting Traffic-shapeRate-limit ModesCoS Interface Configuration Web ExampleLink Aggregation Example #1 Link Aggregation Configuration ExampleLink Aggregation Shows the example network Switching -- Link Aggregation -- Configuration Web User Guide Limited Warranty USA only Web User Guide Limited Warranty USA only Web User Guide Registration Web User Guide Technical Support Web User Guide Technical Support Web User Guide Technical Support Web User Guide Technical Support Web User Guide Technical Support Web User Guide Technical Support Web User Guide Technical Support Web User Guide Technical Support Web User Guide Technical Support Web User Guide Technical Support Web User Guide Technical Support Web User Guide Technical Support Web User Guide Technical Support Web User Guide International Offices Italy India BrasilWeb User Guide Appendix a Cables and Connectors Shows the standard RJ-45 pin assignmentsWeb User Guide Appendix B Connector Pinouts Following tables show connector pinout informationWeb User Guide Appendix C Cable Lengths and Wavelengths Following tables show maximum cable lengths and wavelengthsWeb User Guide
Related manuals
Manual 1 pages 56.33 Kb