Linksys BEFVP41 manual Setup MAC Address Clone, Setup Advanced Routing, MAC Clone

Page 12

Chapter 3

Advanced Configuration

Setup > MAC Address Clone

A MAC address is a 12-digit code assigned to a unique piece of hardware for identification. Some ISPs will require you to register a MAC address in order to access the Internet. If you do not wish to re-register the MAC address with your ISP, you may assign the MAC address you have currently registered with your ISP to the Router with the MAC Address Clone feature.

Setup > MAC Address Clone

MAC Clone

MAC Clone Service  To have the MAC address cloned, select Enable.

MAC Address  Enter the MAC address registered with your ISP here.

Clone  Click this button to clone the MAC address of the computer you are using.

Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.

Setup > Advanced Routing

This screen is used to set up the Router’s advanced functions. Dynamic Routing automatically adjusts how packets travel on your network. Static Routing sets up a fixed route to another network destination.

Setup > Advanced Routing

EtherFast Cable/DSL VPN Router with 4-Port Switch

Advanced Routing

Dynamic Routing

NAT  If this Router is hosting your network’s connection to the Internet, keep the default, Enabled. If another router exists on your network, select Disabled. (When NAT is disabled, the DHCP server feature is also disabled.)

Transmit RIP Version  To use dynamic routing for transmission of network data, select the protocol you want: RIP1, RIP1-Compatible, or RIP2.

Receive RIPVersion  To use dynamic routing for reception of network data, select the protocol you want, RIP1 or RIP2.

Static Routing

Astatic route is a pre-determined pathway that network information must travel to reach a specific host or network. Enter the information described below to set up a new static route.

Select Entry  To set up a static route between the Router and another network, select a number from the drop- down list. Click Delete Entry to delete a static route.

Destination IP Address  Enter the IP address of the remote network or host to which you want to assign a static route.

Subnet Mask  Enter the subnet mask. This determines which portion of a Destination IP Address is the network portion, and which portion is the host portion.

Gateway  Enter the IP address of the gateway device that allows for contact between the Router and the remote network or host.

Hop Count  Enter the maximum number of steps between network nodes that data packets will travel. A node is any device on the network, such as a computer, print server, or router.

Interface  Select the appropriate interface. This tells you whether the Destination IP Address is on the LAN (Local Area Network) or the Internet.

Click Show Routing Table to view the static routes you have already set up.

Advanced Routing > Routing Table

8

Page 11 Page 13
Image 12
Page 11 Page 13
Contents EtherFast Cable/DSL VPN Router with 4-Port Switch About This Guide Icon DescriptionsOnline Resources Copyright and TrademarksTable of Contents Appendix F Software License Agreement Computer using VPN client software to VPN Router Chapter IntroductionIntroduction to VPNs VPN ExamplesVPN Security Chapter Product Overview Front PanelBack Panel Chapter Advanced Configuration How to Access the Web-Based UtilitySetup Basic Setup Internet SetupStatic IP PPPoEOptional Settings and MTU Heart Beat SignalSetup Ddns Network SetupSetup MAC Address Clone Setup Advanced RoutingMAC Clone Advanced RoutingSecurity Firewall Security VPNFirewall VPN PassthroughVPN Tunnel Local Secure Group and Remote Secure GroupRemote Security Gateway Advanced Setting Key ManagementStatus Auto IKEAccess Restrictions PhaseOther Settings ProposalInternet Access To create an Internet Access policyApplications and Gaming Port Range Forwarding Port Range ForwardingApplications & Gaming Port Triggering Port TriggeringUPnP Forwarding Triggered RangeAdministration Management Applications and Gaming DMZAdministration Log Gateway PasswordUPnP LogAdministration Diagnostics Administration Factory DefaultsFactory Defaults Ping TestAdministration Firmware Upgrade Status GatewayStatus Local Network Local Network Dhcp Client TableAppendix a Troubleshooting Your computer cannot connect to the InternetAppendix B VPN Tunnel OverviewInstructions Appendix C Specifications BEFVP41Limited Warranty Obtaining Warranty ServiceExclusions and Limitations Technical Support Safety Notices FCC StatementIndustry Canada Statement Avis d’Industrie CanadaDansk Danish Miljøinformation for kunder i EU Regulatory Information Norsk Norwegian Miljøinformasjon for kunder i EU Regulatory Information Software in Linksys Products Software LicensesSchedule 1 Linksys Software License Agreement Schedule PreambleSoftware License Agreement Software License Agreement No Warranty GNU Lesser General Public License Software License Agreement Software License Agreement Software License Agreement No Warranty OpenSSL License Original SSLeay License8112021NC-JL

BEFVP41 specifications

The Linksys BEFVP41 is a sophisticated yet user-friendly VPN router designed primarily for small office and home office networks. Known for its robust performance and versatility, it stands out as a solid choice for users looking to enhance their network security and connectivity.

One of its key features is the built-in VPN support, which allows users to establish secure connections to remote networks or clients. The BEFVP41 supports up to 50 simultaneous VPN connections, making it an excellent option for small businesses that require secure remote access for their employees without compromising on speed or reliability.

The router employs advanced security protocols including IPsec, which is well-known for ensuring encrypted communication over the internet. This level of security enables users to safeguard sensitive data and maintain privacy while accessing their networks remotely, critical for businesses that handle confidential information.

In terms of connectivity, the BEFVP41 is equipped with four Ethernet ports that support 10/100 Mbps speeds, allowing for high-speed wired connections. It also features a WAN port for connection to a broadband modem, ensuring a fast and stable internet connection. The router supports various connection types, including DHCP, static IP, and PPPoE, making it versatile for different networking environments.

Additional features include a user-friendly web-based interface, which simplifies the setup and configuration process for users. This intuitive design is combined with powerful QoS (Quality of Service) capabilities, enabling prioritized bandwidth allocation to specific applications or users, ensuring that critical business applications have the necessary speeds and reliability.

The BEFVP41 also offers dynamic DNS support, which allows users to access their home or office network using a domain name instead of remembering an IP address. Moreover, it includes a DHCP server for automated IP address assignment, making network management more streamlined.

Overall, the Linksys BEFVP41 combines essential networking technologies and security features into a compact design suitable for any small business or home office environment. With its robust performance, extensive VPN capabilities, and user-friendly interface, it caters effectively to the diverse needs of modern network requirements. The BEFVP41 is a reliable solution for those looking to enhance their connectivity while maintaining security and ease of use.
Top Page Image Contents