Linksys WAP4400N manual Appendix H Regulatory Information, FCC Statement

Page 63

Wireless-N Access Point with Power Over Ethernet

Appendix H: Regulatory Information

FCC Statement

This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna

•Increase the separation between the equipment or devices

•Connect the equipment to an outlet other than the receiver's

•Consult a dealer or an experienced radio/TV technician for assistance

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjuction with any other antenna or transmitter.

To maintain compliance with FCC RF exposure compliance requirements, please follow operation instruction as documented in this manual.

Linksys declares that WAP4400N (FCC ID: Q87-WAP4400N) is limited in CH1~CH11 for 2.4 GHz by specified firmware controlled in U.S.A.

Safety Notices

Caution: To reduce the risk of fire, use only No.26 AWG or larger telecommunication line cord. Do not use this product near water, for example, in a wet basement or near a swimming pool.

Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning.

Industry Canada (Canada)

This device complies with Canadian ICES-003 and RSS210 rules. Cet appareil est conforme aux normes NMB-003 et RSS210 d'Industrie Canada.

Appendix H: Regulatory Information

57

Image 63

Contents Wireless-N Access Point with Power Over Ethernet Copyright and Trademarks How to Use this User GuideTable of Contents Appendix a Troubleshooting Appendix B Wireless SecurityFrequently Asked Questions List of Figures Example of a Simple Wireless Network18 Administration Management Welcome IntroductionWhat’s in this User Guide? Wireless-N Access Point with Power Over Ethernet Network Layout Planning Your Wireless NetworkNetwork Topology RoamingExample of a Simple Wireless Network Wireless-N Access Point with Power Over Ethernet LEDs Getting to Know the Wireless-G Exterior Access PointBack View PortsAntennas and Positions Reset ButtonStandalone Position and its Antenna Setup Connecting the Wireless-N Access Point OverviewConnection Placement Options Stand OptionWall-Mount Option Accessing the Utility Setting Up the Wireless-N Access PointSetup WirelessNavigating the Utility Administration Security MonitorStatus Network Setup Configuring the Wireless-N Access PointSetup Basic Setup Tab Basic SetupTime Setup Time TabBasic Settings Wireless Basic Wireless Settings TabWireless-N Access Point with Power Over Ethernet WPA-Personal aka WPA-PSK Wireless Wireless Security TabWireless Security DisabledWPA2-Personal Mixed WPA2-PersonalWPA2-Enterprise WPA-EnterpriseWEP WPA2-Enterprise MixedConnection Control Wireless Wireless Connection Control TabWireless Connection Control Wireless Client ListAdvanced Wireless Wireless Advanced Wireless Settings TabWireless-N Access Point with Power Over Ethernet Wireless Security Monitor Security Monitor TabSecurity Monitor Accounts Management Administration Management TabWeb Access Local AP PasswordIdentification Log Administration Log TabWireless-N Access Point with Power Over Ethernet Firmware Upgrade Administration Factory Default TabAdministration Firmware Upgrade Tab Factory DefaultReboot Administration Reboot TabConfig Management Administration Config Management TabStatus Local Network Tab InformationLocal Network Wireless Network Status Wireless TabSystem Performance WiredWireless Status System Performance TabWireless-N Access Point with Power Over Ethernet Frequently Asked Questions Appendix a TroubleshootingWhat Ieee 802.11g features are supported? What is the ISM band? Does the Access Point function as a firewall? Wireless-N Access Point with Power Over Ethernet Appendix B Wireless Security Security PrecautionsSecurity Threats Facing Wireless Networks Appendix B Wireless Security Wireless-N Access Point with Power Over Ethernet Appendix C Upgrading Firmware Appendix D Windows Help Shared ResourcesNetwork Neighborhood/My Network Places Appendix E Glossary Wireless-N Access Point with Power Over Ethernet Wireless-N Access Point with Power Over Ethernet Wireless-N Access Point with Power Over Ethernet Wireless-N Access Point with Power Over Ethernet Model WAP4400N Standards Appendix F SpecificationsStorage Humidity Operating HumidityLimited Warranty Appendix G Warranty InformationFCC Statement Appendix H Regulatory InformationWireless-N Access Point with Power Over Ethernet Wireless-N Access Point with Power Over Ethernet Wireless-N Access Point with Power Over Ethernet Wireless-N Access Point with Power Over Ethernet Dual-Band Wireless Access Point Appendix I Contact Information Need to contact Linksys?Information section in this Guide

Related manuals

Manual 69 pages 36.4 Kb

Manual 3 pages 13.4 Kb