Hifionics BRZ1200.1D Single AMP Installation Procedure, Not Used, Dual AMP Installation Procedure

BRZ2100.1D / BRZ2400.1D MONO AMPLIFIER APPLICATIONS

Basic application

SINGLE AMP INSTALLATION PROCEDURE:

1.Connect the amp LINE INPUTS to the Radio/CD player full range or mono line out puts with good quality RCA interconnect cables.

2.Plug in the HFR-3 remote module into the amp REMOTE INPUT jack.

3.Route a 0 gauge power cables directly to the vehicle battery with an in-line fuse.

4.Connect a 0 gauge ground cables directly to chassis ground with in 36” of the amp.

-Be sure to remove any paint or primer from the ground point.

-Use a nut, bolt and lock washer to secure the ground cable to the chassis ground.

5.Connect the subwoofer(s) in accordance to the diagrams below.

6.Make sure the MASTER/SLAVE switch is in the MASTER position.

Note: The amplifier will not work if the MASTER/SLAVE switch is in the Slave position

FULL RANGE
STEREO LINE INPUT	Y-ADAPTOR

NOT USED

Note: You can use the Radio/CD designated mono line output or a full range stereo line output. For full range stereo line output, you will need an optional “Y-Adaptor” as shown.

DESIGNATED

MONO OUTPUT FROM HEAD UNIT

BOOST

HFR -3 MIN MAXX

	R	L	INPUT
	R	L	OUTPUT	BALANCED
	9V 0.2V		INPUT LEVEL
	0 180		PHASE
	0dB 10dB		REMOTE
			BASS EQ
	15Hz 35Hz		SONIC	SUB
	35Hz		LOW
	250Hz		PASS
INPUT SLAVE	OUTPUT MASTER			PROTECT	POWER
OUT			IN

		MONO
		SUBWOOFER
		PARALLEL MONO
	+	SUBWOOFERS
	OUTPUT +
		2 OHMS EACH MINIMUM
	SPEAKER - -
	REM	REMOTE TURN-ON
		POWER	SPEAKER
		+12V GND	REM - - + +
INPUT	GND	CHASSIS GROUND
POWER	BATT+12V	TO BATTERY + 12 Volts
		VIA FUSE

DUAL AMP INSTALLATION PROCEDURE:

1.Connect the amp LINE INPUTS to the Radio/CD player full range or mono line out puts with good quality RCA interconnect cables.

2.Plug in the HFR-3 bass remote module into the amp REMOTE INPUT jack on the Master amp. This will allow the Master amp to control both Master and Slave amps with just one Bass Remote.

3.Connect an RCA jumper cable from the Master amp MASTER OUTPUT to the Slave amp SLAVE INPUT. Note: This will “link” the amps so that the Master amp crossover switches will control both the Master and Slave amps. The Slave amp crossover switches will be bypassed.

4.Route two 0 gauge power cables directly to the vehicle battery with an in-line fuse.

5.Connect two 0 gauge ground cables directly to the chassis with in 36” of the amp.

-Be sure to remove any paint or primer from the ground point.

-Use a nut, bolt and lock washer to secure the ground cable to the chassis ground.

6.Make sure the Master amp MASTER/SLAVE switch is in the MASTER position. Make sure the Slave amp MASTER/SLAVE switch is in the SLAVE position.

7.Connect the subwoofer(s) in accordance to the diagrams below.

8.Connect a 12 gauge jumper from Master amp speaker - to Slave amp speaker - as

shown below.

Linking two amps for single or dual subwoofer application

Amplifiers are stable to 2-Ohms linked

	R	L	INPUT
DESIGNATED
MONO OUTPUT			OUTPUT
FROM HEAD UNIT	R	L		BALANCED
			INPUT LEVEL
	9V 0.2V
BOOST	0 180		PHASE
HFR -3 MIN MAXX	0dB 10dB		REMOTE
			BASS EQ
Master remote controls
both amplifiers when	15Hz 35Hz		SONIC	SUB
LINKED

	+
(MASTER)	OUTPUT +
	SPEAKER - -
	REM

12 GAUGE

				35Hz		LOW
				250Hz		PASS
		INPUT SLAVE	MASTER	OUTPUT
	MASTER OUTPUT TO SLAVE	OUT				IN
RCA JUMPER CABLE			RR	9V 0.2V 0 1800dB 10dB 15Hz 35Hz	LL	BALANCEDSUB INPUT OUTPUT INPUT LEVEL PHASE REMOTE BASS EQ SONIC

IN

OUTPUT

MASTER

INPUT	OUT
SLAVE

(SLAVE)

INPUT	GND
POWER	BATT+12V

	+
OUTPUT	+
SPEAKER	- -
	REM

JUMPER WIRE

INPUT	INPUT SLAVE	OUTPUT MASTER	35Hz 250Hz	LOW PASS
	OUT			IN

	IN	INPUT	GND
OUTPUT
	OUT	POWER	BATT+12V
INPUT
MASTER
SLAVE

5