3Com MSR 20, MSR 30, MSR 50 DTE and DCE, Interface attributes of the FIC-2SAE/FIC-4SAE/FIC-8SAE

Page 154

154CHAPTER 4: FLEXIBLE INTERFACE CARDS

DTE and DCE

An FIC-SA card is usually connected to an external modem for dialing purpose, where an appropriate baud rate setting is required.

The synchronous serial interface can work in either DTE or DCE mode. Two directly connected devices must work as DTE and DCE respectively. The DCE provides clock synchronization and specifies the communication rate, whereas the DTE accepts clock synchronization and communicates at the specified rate.

The router normally works as a DTE. To identify whether the equipment connected to the router is DTE or DCE, refer to the manual shipped with the equipment.

Speed and transmission segment of synchronous/asynchronous serial interface

In different operating modes, the synchronous/asynchronous serial interface supports different electric signal specifications and baud rates. In addition, the maximum signal transmission segment depends not only on the specified baud rate but also on the selected cable. The following table shows how the cable type, baud rate, and the maximum signal transmission segment related to each other.

Table 108 Speed and transmission segment of the V.24 (RS232)/V.35 cable

V.24 (RS232)		V.35
	Max. transmission		Max. transmission
Baud rate (bps)	segment	Baud rate (bps)	segment

2400	60 m (196.9 ft.)	2400	1250	(4101 ft.)

4800	60 m (196.9 ft.)	4800	625 m (2050.5 ft.)

9600	30 m (98.4 ft.)	9600	312 m (1023.6 ft.)

19200	30 m (98.4 ft.)	19200	156 m (511.8 ft.)

38400	20 m 65.6 ft.)	38400	78 m (255.9 ft.)

64000	20 m (65.6 ft.)	56000	60 m (196.9 ft.)

115200	10 m (32.8 ft.)	64000	50 m (164 ft.)

-	-	2048000	30 m (98.4 ft.)

n When a V.24 cable is used, the baud rate of the FIC-SA in synchronous mode shall not exceed 64 Kbps.

Interface Attributes The following table describes the interface attributes of the FIC-SAE:

Table 109 Interface attributes of the FIC-2SAE/FIC-4SAE/FIC-8SAE

	Description
Attribute	Synchronous	Asynchronous

Connector	DB-28

Number of connectors	2 (FIC-2SAE)
	4 (FIC-4SAE)
	8 (FIC-8SAE)

Image 154

Contents H3C MSR 20/30/50 Series Routers 3Com Corporation Campus Drive Marlborough, MA USA United States Government LegendContents 161 143FIC-8ASE/FIC-16ASE FIC-8E1/FIC-8E1-F236 Ande Module 229 Snde Module 230 Vcpm Module 231SIC/DSIC Purchase Guide 235 FIC/DFIC Purchase Guide 238 ESM/VPM/VCPM Purchase GuidePage Text Conventions Lists icon conventions that are used throughout this guideLists text conventions that are used throughout this guide Convention DescriptionRelated DocumentationCards SIC/DSIC InterfaceWAN interface cards Overview MIM/DMIM/XMIM Overview Routers FIC/DFIC InterfacePort 10Base-T/100Base-TX FE interface card FIC-4FE Overview Voice interface cards SIC/MIM/FIC PurchaseGuideline Encryption cardsTools required Installation/Removal A SIC/MIM/FICInstalling a SIC Flat-module screwdriverInstalling a MIM Installing/Removing aRemoving a SIC Installing a MIM Removing a MIMRepeat these steps to install all the other FICs Execute the undo remove slot command howeverOperation by using the undo remove slot command CommandOverview Router SIC-1FEASo on Or slotLink Description of the LEDs on SIC-1FEA panelLED ACTDescription Attribute Synchronous Asynchronous SIC-1SAEInterface attributes of the SIC-1SAE DTE, DCESIC-1SAE panel LEDs on SIC-1SAE panelDCE cable DTE cableRS449 DTE cable RS449 DCE cableRS530 DTE cable RS530 DCE cableInterface attributes of SIC-1EPRI/SIC-1E1-F SIC-1EPRI/SIC-1E1-FAttribute Description DIP switch Description Ohm impedance Impedance 120-ohmSIC-1E1-F panel is shown in the following figure Interface LEDsSIC-1EPRI panel is shown in the following figure Description of the LEDs on SIC-1EPRI/SIC-1E1-F panelBalanced twisted pair cables SIC-1EPRI/SIC-1E1-F. By default, they are not suppliedConnecting the Interface Cable Addition, a 75-ohm to 120-ohm adapter is availableMarked TX SIC-1TPRI/SIC-1T1-F Interface attributes of SIC-1TPRI/SIC-1T1-FSIC-1TPRI panel SIC-1T1-F panelDefault, they are not supplied Description of the LEDs on SIC-1TPRI/SIC-1T1-F panelInterface LEDs SIC-1AM panel SIC-1AM/SIC-2AMInterface attributes of SIC-1AM/SIC-2AM SIC-1FXS/SIC-1FXO SIC-2FXS/SIC-2FXO Low-End and Mid-Range Series Routers Cable ManualSIC-1FXS/SIC-1FXO Interface LEDs SIC-1FXS/SIC-1FXO panelSIC-2FXS/SIC-2FXO panel SIC-2FXS/SIC-2FXOPoE SIC-4FSW/SIC-4FSW-PoDSIC-9FSW/DSIC-9FS SIC-2FXS/SIC-2FXO includes a ferrite core telephone cableInterface Attributes MDI/MDIXCable To a Hub or LAN Switch using a straight-through cableLEDs on the panel Maximum SIC-1GECInterface Attributes of the SIC-1GEC SFPSIC-1GEC panel Connecting Ethernet fiber interface cable Connecting Ethernet electrical interface cableSIC-1VE1 SignalsConfigure a VPM based on voice traffic CardDIP Description of DIP switch settings of SIC-ERRI/SIC-1E1-FConfiguration Description Ohm impedanceFollowing table describes the LEDs on the SIC-1VE1 panel SIC-1VE1 panelSIC-1VE1. By default, they are not supplied SIC-1VT1 Interface Attributes of the SIC-1T1-F Following table describes the LEDs on the SIC-1VT1 panelDescription on SIC-1VT1 LED SIC-1ADSL delivers these features SIC-1ADSLInterface attributes of the SIC-1ADSL Following table describes the LEDs on the card panelSIC-1ADSL Connecting the SIC-1ADSL SIC-1ADSL-ILEDs on the SIC-1ADSL-I panel Interface attributes of the SIC-1ADSL-I1ADSL-I SIC-1BS/SIC-2BS&SIC-1 BU/SIC-2BU Connect the SIC-1ADSL-IInterface attributes of SIC-1BS/SIC-2BS and SIC-1BU/SIC-2BU SIC-1BS/SIC-2BS RJ45LEDs on SIC-1BS/SIC-2BS and SIC-1BU/SIC-2BU panels SIC-1BSV/SIC-2BSV LEDs on SIC-1BSV/SIC-2BSV panel Following figure illustrates the SIC-2BSV panelInterface attributes of SIC-1BSV/SIC-2BSV SIC-1BSV SIC-2BSVStraight-through Isdn S/T cable Crossover Isdn S/T cableSIC-1FEF SFP/LCLEDs on SIC-1FEF panel Press the button on the connector to remove itFollowing table describes the LEDs on the SIC-1FEF panel Status DescriptionSIC-8AS Interface attributes of SIC-8ASLEDs on SIC-8AS panel Following table describes the LEDs on the SIC-8AS panelLINK/ACT Customized cable Smart Interface Cards Interface attributes of MIM-1FE/MIM-2FE/MIM-4FE MIM-1FE/MIM-2FE/MI4FE Modules MIM-1FE MIM-2FE MIM-4FEInterface Cable Ethernet cable MIM-2FE panel is shown in the following figureMIM-4FE panel is shown in the following figure ActiveModule MIM-1GBE/MIM-2GBEMaking Ethernet cable Description Attribute Interface attributes of MIM-1GBE/MIM-2GBEDescription of the LEDs on the MIM-1GBE/MIM-2GBE panel MIM-1GBE MIM-2GBEInterface attributes of MIM-1GEF/MIM-2GEF MIM-1GEF/MIM-2GEFCable Manual MIM-1GEF MIM-2GEFMIM-1GEF panel MIM-2GEF panelBy Lucent Are not providedMIM-8SAE Module MIM-2SAE/MIM-4SAEInterface attributes of MIM-2SAE/MIM-4SAE/MIM-8SAE MIM-8SAE panel is shown in the following figure MIM-4SAE panel is shown in the following figureDescription of the LEDs on the MIM-2SAE/MIM-4SAE panel 24 DTE cable RS449 DTE cable Connecting the Interface Cable Interface attributes of MIM-8ASE/MIM-16ASE MIM-8ASE/MIM-16ASDescription Attribute MIM-8ASE module MIM-16ASE module Mid-Range Series Routers Cable Manual MIM-16ASE panel is shown in the following figureRemoval tends to damage the module and even the device 4E1/MIM-1E1-F/MI 2E1-F/MIM-4E1-F Modules E1-F modules do not support PRI modeMIM-1E1/MIM-2E1/MI Introduction MIM-1E1/MIM-2E1/MIM-4E1MIM-1E1 panel E1 75-ohm unbalanced coaxial cable E1 120-ohm balanced twisted pair cableConversion cable for MIM-4E1/MIM-4E1-F module 120-ohm 4E1 conversion cableSee Low-End and Mid-Range Series Routers Cable Manual Module MIM-1E1/1E1-F MIM-2E1/2E1-F MIM-4E1/4E1-FDIP Local Rx wire to the remote Tx wire Connecting interface cable of MIM-4E1/MIM-4E1-F MIM-8E1-F module MIM-8E1/MIM-8E1-FIntroduction MIM-8E1 module Interface attributes of the MIM-8E1 and the MIM-8E1-FMIM-8E1 120-ohm panel Description of the LEDs on the MIM-8E1/MIM-8E1-F panel4T1/MIM-1T1-F/MI 2T1-F/MIM-4T1-F Modules MIM-1T1/MIM-2T1/MIIntroduction MIM-1T1/MIM-2T1/MIM-4T1 module CT1, Isdn PRI FT1MIM-1T1 panel LP/ALExtending a T1 cable MIM-8T1-F module MIM-8T1/MIM-8T1-FIntroduction MIM-8T1 module Interface attributes of the MIM-8T1 and the MIM-8T1-FMIM-8T1 panel Description of the LEDs on the MIM-8T1/MIM-8T1-F panelMIM-1CE3 Module Accessing of E3 traffic when working in E3 modeSmaller than or equal to 128, when working in CE3 mode E2-to-E1 demultiplex. E23 and E12 discussed here representMIM-1CT3 Module Description of the LEDs on the MIM-1CE3 panelFollowing table describes the LEDs on the MIM-1CT3 panel Accessing of T3 traffic when working in T3 modeMIM-1CT3 panel is shown in the following figure Interface attributes of MIM-1CT3Description of the LEDs on the MIM-1CT3 panel MIM-4BSE ModuleInterface attributes of the MIM-4BSE Following table describes how to set jumpers Jumper settings of the MIM-4BSE exampleJumper settings & description Default Set the jumpers on the MIM-4BSEFollowing table describes the LEDs on the module panel LEDs on the MIM-4BSE panelInterface attributes of MIM-1G.SHDSL module MIM-1G.SHDSLAttribute MIM-1G.SHDSL module Pstn network MIM-1AMM/MIM-1AS MIM-1ASLInterface Cable Interface module MIM-1AMMFollowing table describes the LEDs on the panels LEDInterface Optical Fiber 25km, the interface will be unable to receive signalsMIM-1AE3 Module Whereas MIM-1ASM/MIM-1ASL modules should be connected withFollowing table describes the LEDs on the MIM-1AE3 panel Description of the LEDs on the MIM-1AE3 panelFollowing table describes the LEDs on the MIM-1AT3 panel MIM-1AT3 ModuleMIM-1AT3 panel is shown in the following figure Interface attributes of MIM-1AT3 moduleMIM-1POS Module Description of the LEDs on the MIM-1AT3 panelDescription of the LEDs on the MIM-1POS panel Following table describes the LEDs on the MIM-1POS panelInterface attributes of the MIM-1POS MIM-1POSMIM-2FXS/MIM-2FXO/MIM-2E&M MIM-2FXS/MIM-2FXO/ MIM-2E&M and MIM-4FXS/MIM-4FXO/ MIM-4E&MMIM-4FXS/MIM-4FXO/MIM-4E&M MIM-2FXS panel Interface cable of E&M modules Interface cable of FXS/FXO modulesDescription of the LEDs on voice MIM panels Pinouts of E&M interface cable Bell V 4-wire RING0 RING1 TIP1 TIP0Feature Description MIM-HNDE module featuresMIM-HNDE Module Troubleshooting MIM-2VE1 ModuleInterface attributes of MIM-2VE1 Following table describes the LEDs on the MIM-2VE1 panelMIM-2VE1 module is 1U in height, occupying two slots Description of the LEDs on the MIM-2VE1 panel75-ohm-to-120-ohm adapter with BNC connector MIM-2VT1 Module Voice signalsVPM module is installed on the main board of MIM-2VT1 Module as neededMIM-2VT1 module is 1U in height, occupying two slots Following table describes the LEDs on the MIM-2VT1 panelDescription of the LEDs on the MIM-2VT1 panel MIM-1VE1 Module Interface attributes of MIM-1VE1MIM-1VE1 module is 1U in height, occupying two slots Following table describes the LEDs on the MIM-1VE1 panelDescription of the LEDs on the MIM-1VE1 panel Twisted pair cable, you can use network interface connector VoIP system MIM-1VT1 ModuleInterface attributes of MIM-1VT1 MIM-1VT1 module is 1U in height, occupying two slots Following table describes the LEDs on the MIM-1VT1 panelDescription of the LEDs on the MIM-1VT1 panel MIM-16FSW/MIM-16FSW-PoE/DMIM-24FSW/DMIM-24FSW-PoE MIM-16FSW/MIM-16FSW-P DMIM-24FSW/DMIM-24FS Attribute OE module PoE moduleMIM-16FSW/MIM-16FSW-PoE panel LED status DescriptionInterface Cable 8E1 Module Connecting Ethernet electrical cableMIM-IMA-4E1/MIM-IM Interface attributes of the MIM-IMA-4E1/ MIM-IMA-8E1Description of the LEDs on the IMA-4E1/IMA-8E1 panel Attribute 75-ohm 120-ohmCable Interface attributes of MIM-IMA-4T1/MIM-IMA-8T1 MIM-IMA-4T1/MIM-IM8T1 Module MIM-IMA-4T1 MIM-IMA-8T1MIM-IMA-8T1 panel Interface attributes of MIM-2BSV/MIM-4BSV MIM-2BSV/MIM-4BSVAttribute MIM-2BSV module MIM-4BSV module Following figure illustrates the MIM-4BSV panel Description of the LEDs on the MIM-2BSV/MIM-4BSV panelCrossover Isdn S/T cable Interface attributes of the MIM-1CPOSE/MIM-1CPOST module MIM-1CPOS ModuleMIM-1CPOSE/MIM-1CPOST FC round fiber-optic connector with screw thread There are many types of fiber-optic connectors, such asLEDs on the MIM-1CPOSE/MIM-1CPOST panel Interface attributes of the MIM-1SHL-4W MIM-1SHL-4W ModuleOptical Fiber MIM-1SHL-4WFollowing table describes the LEDs on the MIM-1SHL-4W panel LEDs on the MIM-1SHL-4W panelXMIM-24FSW support the following functions XMIM-16FSW/XMIM-2 4FSWMIM-1SHL-4W and the other end to Dslam through Pstn Auto-sensing at a rate of 10 Mbps or 100 MbpsInterface LEDs shows the XMIM-16FSW panel Interfaces, which are usually used on hubs and LAN SwitchesLEDs of the XMIM-16FSW/XMIM-24FSW FE port Ethernet cable Multifunctional Interface Modules FIC-1FE/FIC-2FE/FIC-4FE interface attributes FIC-1FE/FIC-2FE/FIC-4FFIC-1FE FIC-2FE FIC-4FE Following figure illustrates an FIC-4FE panel Following figure illustrates an FIC-2FE panelLEDs on the FIC-1FE/FIC-2FE/FIC-4FE panel FIC-1GBE/FIC-2GBE Making Ethernet cablesLEDs on the FIC-1GBE/FIC-2GBE panel Interface attributes of the FIC-1GBE/FIC-2GBEFIC-1GBE FIC-2GBE Interface attributes of the FIC-1GEF/FIC-2GEF FIC-1GEF/FIC-2GEFFIC-1GEF FIC-2GEF FIC-1GEF panel LEDs on the FIC-1GEF/ FIC-2GEF panelFIC-2SAE/FIC-4SAE/FIC -8SAE Interface attributes of the FIC-2SAE/FIC-4SAE/FIC-8SAE DTE and DCE24 RS232 Max. transmission Baud rate bps Segment LEDs on the FIC-2SAE/FIC-4SAE panel DTE DCEFollowing figure shows the FIC-8SAE panel DCE cable RS449 DTE cable FIC-8ASE/FIC-16ASE Introduction FunctionsInterface attributes of the FIC-8ASE/ FIC-16ASE FIC-8ASE FIC-16ASEDumb terminal cables, you can make on site by reference to Low-End-and-Mid-Range Series Routers Cable ManualFollowing figure illustrates the FIC-2E1 panel Interface attributes of the FIC-E1 and FIC-E1-F cardsFollowing figure illustrates the FIC-2E1-F panel Following figure illustrates the FIC-4E1 panelFollowing figure illustrates the FIC-1E1-F panel Following figure illustrates the FIC-4E1-F panelLEDs on the FIC-E1 and FIC-E1-F panels E1 120-ohm balanced twisted-pair cableAddition, you are available with 75-ohm-to-120-ohm adapters Interface cable of the FIC-4E1/FIC-4E1-FAddition, you are available with 75-ohm-to-120-ohm adapters FIC-4E1/FIC-4E1-F by default, they are not providedFIC-1E1/F Card IC-1E1-F FIC-2E1/FIC-2E1-F FIC-4E1/FIC-4E1-F Setting DIP switches on the FIC-E1/FIC-E1-F cards End FIC-8E1/FIC-8E1-F Connecting the interface cable of the FIC-4E1/FIC-4E1-FIntroduction FIC-8E1 Interface attributes of the FIC-8E1/FIC-8E1-F card FIC-8E1 120-ohm panelLEDs on the FIC-8E1/FIC-8E1-F panels FIC-1T1-F/FIC-2T1-F/FIC-4T1-F Following figure illustrates the FIC-4T1 panel Following figure illustrates the FIC-2T1 panelInterface attributes of the FIC-T1/FIC-T1-F cards Following figure illustrates the FIC-2T1-F panel Following figure illustrates the FIC-1T1-F panelFollowing figure illustrates the FIC-4T1-F panel LEDs on the FIC-T1 and FIC-T1-F panels Introduction FIC-8T1 FIC-8T1/FIC-8T1-FLEDs on the FIC-8T1 and FIC-8T1-F panels FIC-8T1 panel LEDs on FIC-8T1 and FIC-8T1-F panelsRepresent the demultiplex process FIC-1CE3FIC-1CE3 interface attributes FIC-1CE3 panel LEDs on the FIC-1CE3 panelFIC-1CT3 FIC-1CT3 interface attributesLEDs on the FIC-1CT3 panel FIC-4BSEInterface attributes of the FIC-4BSE Jumper settings of the FIC-4BSE example Set the jumpers on the FIC-4BSE FIC-4BSE panel LEDs on the FIC-4BSE panelInterface attributes of the FIC-1AE3 FIC-1AE3Following table describes the LEDs on the FIC-1AE3 panel FIC-1AE3FIC-1AT3 LEDs on the FIC-1AE3 panelLEDs on the FIC-1AT3 panel Following table describes the LEDs on the FIC-1AT3 panelInterface attributes of the FIC-1AT3 FIC-1AT3Status FIC-1AT3 and another end to the Rx port on another deviceFIC-1AT3 and another end to the Tx port on another device LoopbackInterface attributes of the ATM cards Following figure illustrates the FIC-1ATM-OC3SM panelFollowing figure illustrates the FIC-1ATM-OC3SML panel LEDs on the ATM card panelsInterface attributes of the FIC-1G.SHDSL FIC-1G.SHDSLFIC-1G.SHDSL FIC-1POS LEDs on the FIC-1G.SHDSL panelLEDs on the FIC-1POS panel Following table describes the LEDs on the FIC-1POS panelInterface attributes of the FIC-1POS FIC-1POSFIC-4FXS/FIC-4FXO/FIC FIC-2FXS/FIC-2FXO/FIC2E&M 4E&MFollowing figure illustrates the FIC-4FXS panel Following figure illustrates the FIC-2FXO panelFollowing figure illustrates the FIC-2E&M panel FIC-2FXO/FIC-4FXOInterface cables for the FIC-FXS/FIC-FXO cards Following figure illustrates the FIC-4FXO panelFollowing figure illustrates the FIC-4E&M panel Interface cables for FIC-E&M cardsRouter side Signal at switch side Bell RJ-45 Pin Wire PBXFIC-HNDE Connecting the FIC-2E&M/FIC-4E&M card on siteSelf-made E&M interface cable by the router side Interface attributes of the FIC-HNDE Troubleshooting by reading the LED behaviorsFollowing table describes the LEDs on the FIC-HNDE panel LEDs on the FIC-HNDEFIC-2VE1 Interface attributes of FIC-2VE1FIC-2VE1 panel Description of the LEDs on FIC-2VE1 panelConnecting the Interface Cable Interface attributes of FIC-2VT1 FIC-2VT1FIC-2VT1 panel is shown in the following figure Description of the LEDs on FIC-2VT1 panel FIC-1VE1 panel is shown in the following figure FIC-1VE1Interface attributes of FIC-1VE1 Description of the LEDs on FIC-1VE1 panelDescription of the LEDs on FIC-1VE1 panel VPM module is installed on the main board of FIC-1VT1 FIC-1VT1Interface attributes of FIC-1VT1 Description of the LEDs on FIC-1VT1 panelFIC-16FSW/FIC-16FSW- PoE/DFIC-24FSW/DFIC- 24FSW-PoE FIC-16FSW/FIC 16FSW-PoE Attribute Module DFIC-24FSW/DFIC-24FSW-PoE moduleFIC-16FSW/FIC-16FSW-PoE panel Interface Cable FIC-IMA-4E1 FIC-IMA-4E1/FIC-IMA-8Interface attributes of the FIC-IMA-4E1/FIC-IMA-8E1 FIC-IMA-8E175-ohm FIC-IMA-4E1 panel LEDs on the FIC-IMA-4E1/FIC-IMA-8E1 panel75-ohm 8E1 conversion cable Interface attributes of the FIC-IMA-4T1/FIC-IMA-8T1 FIC-IMA-4T1/FIC-IMA-8FIC-IMA-4T1 FIC-IMA-8T1 FIC-IMA-8T1 panel LEDs on the FIC-IMA-4T1/FIC-IMA-8T1 panelInterface attributes of the FIC-1SHL-4W FIC-1SHL-4WFIC-1SHL-4W FIC-1SHL-4W and the other end to Dslam through Pstn FIC-1CPOSFollowing table describes the LEDs on the FIC-1SHL-4W panel LEDs on the FIC-1SHL-4W panelInterface attributes of the FIC-1CPOSE/FIC-1CPOST FIC-1CPOSE/FIC-1CPOSTFollowing figure illustrates the FIC-1CPOST panel LEDs on the FIC-1CPOSE/FIC-1CPOST panelFIC-2BSV/FIC-4BSV LEDs on the FIC-2BSV/FIC-4BSV panel Following figure illustrates the FIC-4BSV panelInterface attributes of the FIC-2BSV/FIC-4BSV FIC-2BSV FIC-4BSVConnecting the Interface Cable Interface attributes of the FIC-24FXS card FIC-24FXSFollowing figure illustrates the FIC-24FXS panel Description of LEDs on the FIC-24FXS panelFIC-24FXS conversion cable Interface attributes of the DFIC-24FXO24FXS module DFIC-24FXO24FXSFollowing figure illustrates the DFIC-24FXO24FXS panel Description of LEDs on the DFIC-24FXO24FXS panelDFIC-24FXO24FXS Flexible Interface Cards Removing Ande card Ande ModuleFollowing table describes the LEDs on the panel Follow these steps to remove the Ande cardInstalling Ande card Snde ModuleVcpm Module Installing/RemovingInstalling Snde card Snde CardRemoving Vcpm card Installing Vcpm cardFollowing table describes the LEDs on the main board Interface attributes of the Vcpm moduleRouter installed with RTV-SIC-1E1/T1 module Router installed with no RTV-SIC-1E1/T1 moduleESM/VCPM Module SIC/DSIC options SIC/DSIC Purchase GuideSupported and ⋅ means Not supported Interface card 20-20 20-40 50-40 Type 20-2130-16 MIM/DMIM Purchase GuideMIM/DMIM options 30-60 50-60MIM-1CPOSE ⋅ MIM-1CPOST ⋅ MIM-IMA-4T1 ⋅ MIM-IMA-8T1 ⋅ MIM-2FXS ⋅ MIM-4FXS ⋅ MIM-2FXO ⋅ MIM-4FXO ⋅ MIM-4BSE ⋅MIM-1SHL-4W ⋅ MIM-2BSV ⋅ MIM-4BSV ⋅ FIC/DFIC options FIC/DFIC Purchase GuideFIC-1E1-F FIC-2E1-F FIC-4E1-F FIC-1SHL-4W FIC-2BSV FIC-4BSV FIC-24FXS ESM/VPM/VCPMPurchase Guide ESM-ANDE ESM-SNDE VcpmESM/VPM/VCPM options VPM32 VPM24 VPM16 VPM8

Related manuals

Manual 2742 pages 31.98 Kb