Subwoofer bypass control, Overload indicators

Table 2. Recommended subwoofer/main monitor combinations.

consists of a LED in a compact case and a RJ11 cable to connect the case and the "REMOTE" RJ11 connector on the ampliﬁer panel.

Subwoofer bypass control

A bypass control feature is included in the subwoofer circuits so that the effect of the subwoofer on the whole monitor system can be determined. With the bypass switch on, the high pass ﬁlters for the main monitors are overridden and the system behaves as if the subwoofer was not connected. The bypass function has no effect on the LFE input. Two different bypass remote controllers are avail- able as optional equipment: 1092-400 switch that can be connected to a 1/4" jack connec- tor on the ampliﬁer panel and 7000-416 that connects to the "REMOTE" RJ11 connector. The 7000-416 option also includes remote control of the "LFE +10 dB" function and a link for the 7000-415 remote LED option.

necessary to temporarily connect either of the channels to this output.

Power up the system and set the DIP switches 3 (SUM IN MODE) and 4 (LFE +10 dB) on the ﬁrst switch group to "ON" Now you should hear an 85 Hz test signal from the subwoofer and the main monitor connected to the center channel output.

Toggle the -180° phase switch (DIP 4 on the second switch group) on and off, and set

it to the position which gives the lowest sound level at the listening position.

Next toggle the -90° phase switch (DIP 3) on and off, and again set it to the position which gives the lowest sound level.

Finally, set the -180° phase switch (DIP 4) to the opposite setting and deactivate the test signal.

Phase correction method with

test equipment

The following procedure matches the phase between the subwoofer and the main moni- tors using a frequency analyser and a pink

noise generator. Connect a high grade meas- uring microphone to the analyser and feed pink noise into the "CENTER IN" input of the subwoofer. The subwoofer's bass man- agement system will direct the frequencies above 85 Hz to the center main monitor while the subwoofer reproduces the frequencies below 85 Hz.

Position the microphone at the listening position and adjust the input sensitivity of the subwoofer until frequencies below and above 85 Hz are reproduced at equal level. Then adjust the phase control switches for the maximum dip of at least -6 dB at the crossover frequency (85 Hz).

Change the -180° switch to the opposite setting. The phase should now be set correctly and the frequency analyser should show a smooth response around 85 Hz.

Overload indicators

The mode indicator LED on the ampliﬁer panel will turn from green to yellow to indi- cate clipping and then to red to indicate that the protection circuit has activated. If this occurs frequently, reduce the input level to the subwoofer until the LED remains green.

If the LED on the ampliﬁer panel is not easily visible, the optional Remote LED Kit can be used to bring it into view. The kit

Subwoofer in analogue matrix

surround sound systems.

When using Genelec 7060A, 7070A or 7171A subwoofers in a consumer analogue matrix surround sound system, such as Dolby Sur- round, Dolby Pro-Logic or Pro-Logic II or a professional matrix decoder such as a Dolby SDU-4, route the front channels through the subwoofer so that the output of the sub- woofer is matched to the rest of the system and select "Large" setting for the front speak- ers on the decoder. If there is a subwoofer channel output on the decoder it should NOT be connected to the subwoofer's "LFE IN" input since the processing within an ana- logue decoder will conﬂict with the ﬁltering in the subwoofer. Connecting the rear channels to the subwoofer is optional since the rear channels from most matrix decoders are band limited down to 100 Hz.

Monitoring the LFE channel in digital discrete surround sound systems

Some digital surround sound systems use a discrete Low Frequency Effects channel which should be connected to the "LFE IN" input on the ampliﬁer panel. This enables the subwoofer to correctly reproduce all the bass information in the mix.

7060A, 7070A, 7071A specifications

The Genelec 7060A, 7070A, and 7071A are subwoofers renowned for their exceptional performance in studio and home audio environments. Each model brings a unique blend of features, technologies, and characteristics tailored to delivering accurate low-frequency reproduction.

The Genelec 7060A is a compact subwoofer that delivers a powerful bass response in smaller setups. It has a frequency response of 28 Hz to 85 Hz, making it ideal for music production and post-production environments. The 7060A features a high-quality 10-inch woofer and utilizes Genelec's Directivity Control Waveguide technology, which ensures consistent sound distribution across the listening area. Its robust built-in amplifier provides 100 watts of power, allowing it to integrate seamlessly with main monitors while maintaining clarity and impact.

Moving to the Genelec 7070A, this model offers an elevated performance level suitable for medium-sized spaces. It features an innovative 12-inch woofer and a frequency response extending from 25 Hz to 85 Hz. The 7070A incorporates Genelec's advanced Signal Intelligent Amplification technology, which optimizes the amplifier's performance in real-time, ensuring maximum efficiency and minimal distortion. This subwoofer is designed to produce tight, punchy bass, making it a favorite among professionals in film and music production.

Finally, the Genelec 7071A is designed for larger environments where more power and control are required. This model includes a 12-inch woofer and an impressive frequency response from 22 Hz to 85 Hz. The 7071A features Genelec's enclosure design principles, which minimize unwanted resonance and vibrations, delivering a clean and accurate bass response. Moreover, it integrates seamlessly with Genelec's Smart Active Monitoring systems, allowing for advanced room-tuning capabilities through its built-in DSP.

All three models are designed with Genelec's commitment to sustainability and durability, featuring non-toxic materials and recyclable enclosures. The minimalist design of these subwoofers not only makes them visually appealing but also enhances their adaptability in various sound environments.

In summary, the Genelec 7060A, 7070A, and 7071A subwoofers stand out as exceptional choices for anyone seeking high-quality low-frequency audio performance. Their advanced technologies and thoughtful design cater to both casual listeners and professional sound engineers, ensuring accurate and powerful sound reproduction.