Step 1: Insert Batteries
1.Slide open the battery compartment cover on the back of the scanner.
2.Set the switch according to the type of batteries you are installing: ALKALINE or
3.Place 3AA batteries into the battery compartment.
4.Replace the cover.
| Warning: Only set the switch inside the |
| battery compartment to |
To charge batteries: | with |
1. Set the switch to | use |
switch is set to |
2.Install rechargeable batteries.
3.Connect an external power source to the 6V 800mA jack.
Note: The scanner stops charging automatically after a maximum of 14 hours.
RACING SCANNER
Quick Start Guide
Step 2: Install Antenna
Attach the supplied antenna to the scanner by screwing it tightly onto the anchor post at the top of the radio.
When using an external antenna, always use
feet from the scanner, use
Step 3: Basic Operations
Turning on the Scanner
Press and hold / .
Setting the Volume
1. Push the SEL/VOL/SQL knob.
2. Rotate the knob to select the volume level from 0 to 15.
Setting the Squelch
1. Press Func.
2. Push the SEL/VOL/SQL knob.
3. Rotate the knob to select the squelch level from 0 to 15.
Step 4: Using Your Scanner at the Racetrack
Before You Get to the Track
Your scanner is preprogrammed with all of the drivers and their possible frequencies that were known when it was manufactured.
Before you leave for the track, check the Internet to see if there are any frequency updates available for your race. You can save time at the track by setting up as much as possible before you leave.
When You Get to the Track
When you arrive at the race, get a list of the frequencies in use that race day. These are normally available for sale on the way into the facility. This list will show the actual frequency being used by each driver that day, as well as some other useful frequency information.
Then, follow the steps in the following sections to adjust the scanner settings.
Load the Preset Race Frequency List
For your convenience, six car race frequencies are preprogrammed. You can use one of these race frequencies by loading it to the channel banks.
To load the race frequencies:
1.Press Menu.
2.Rotate the knob to select 1: Preset Race, then press EPGM.
3.Rotate the knob to select 1: Load Race, then press EPGM.
4.Rotate the knob to select one of the races, then press EPGM.
5.If you select races A, B or C, Load Bank X into Bank 0 Yes=”1” / No=”3” appears.
If you select races D, E, or F, Load Bank X into Bank 0 and 1 Yes=”1” / No=”3” appears.
6.Press 1 to program the race or press 3 to cancel.
Program Driver Frequencies
To select the appropriate frequency for each driver:
1.Press CAR, enter the car’s number, then press EPGM.
2.If the car number is not stored, Car# XX is not stored. Program new car? Yes = “E” / No = “.” appears.
3.Press EPGM to edit the tag.
4.Enter the tag you want to assign to the car number (such as driver’s name), then press
EPGM.
5.Enter the frequency of the car, then press
EPGM.
6.If you want to input another frequency to the car, press EPGM.
To edit a tag:
•Press the number/letter buttons multiple times until the desired letter appears.
•Rotate the knob clockwise to move the cursor to the left, counterclockwise to move to the right.
•Press Func to toggle the input mode between ABC, abc, and 123.
•Press •CLR once to erase one character. Press and hold to erase all characters.
•Press EPGM to save the tag and exit editing tag.
Monitor a Car
To listen to the transmissions from one car:
1.Press CAR, enter the car number, then press EPGM.
Or
1.Select the car from a list. Press CAR then press EPGM.
2.Rotating the knob to the desired car, then press EPGM.
Select the Car’s Primary Frequency
Primary frequency is the frequency which is selected first when a car has two or more frequencies. By default, the frequency in the smallest channel works as the primary frequency.
To change a car’s primary frequency:
1.Show the channel where the car number is programmed.
2.Press the Func key and rotate the knob to select the other frequency.
Primary frequency is also changed automatically in the following situations:
•Selecting car channel by rotating the knob during manual mode.
•Pressing SCAN when you monitor a car channel found by scan mode.
©2007. RadioShack Corporation.
All rights reserved. RadioShack and RadioShack.com are trademarks used by RadioShack Corporation.
09A07