Advantech AWS-8248 user manual Safety Instructions

Page 5

Safety Instructions

1.Read these safety instructions carefully.

2.Keep this User's Manual for later reference.

3.Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning.

4.For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible.

5.Keep this equipment away from humidity.

6.Put this equipment on a reliable surface during installation. Dropping it or let- ting it fall may cause damage.

7.The openings on the enclosure are for air convection. Protect the equipment from overheating. DO NOT COVER THE OPENINGS.

8.Make sure the voltage of the power source is correct before connecting the equipment to the power outlet.

9.Position the power cord so that people cannot step on it. Do not place anything over the power cord.

10.All cautions and warnings on the equipment should be noted.

11.If the equipment is not used for a long time, disconnect it from the power source to avoid damage by transient overvoltage.

12.Never pour any liquid into an opening. This may cause fire or electrical shock.

13.Never open the equipment. For safety reasons, the equipment should be opened only by qualified service personnel.

14.If one of the following situations arises, get the equipment checked by service personnel:

a.The power cord or plug is damaged.

b.Liquid has penetrated into the equipment.

c.The equipment has been exposed to moisture.

d.The equipment does not work well, or you cannot get it to work according to the user's manual.

e.The equipment has been dropped and damaged.

f.The equipment has obvious signs of breakage.

15.DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE MAY GO BELOW -20° C (-4° F) OR ABOVE 60° C (140° F). THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT SHOULD BE IN A CONTROLLED ENVIRONMENT.

The sound pressure level at the operator's position according to IEC 704-1:1982 is no more than 70dB (A).

DISCLAIMER: This set of instructions is given according to IEC 704-1. Advan- tech disclaims all responsibility for the accuracy of any statements contained herein.

v

Page 4 Page 6
Image 5
Page 4 Page 6
Contents AWS-8248 Copyright Acknowledgements FCC Class a Additional Information and Assistance Packing ListSafety Instructions Wichtige Sicherheishinweise Contents Chapter Macro Key Programming Introduction Introduction Front-accessible control panelColor LCD Key sealed-membrane operating keypadConvenient work drawer Passive backplanesSpecifications Passive backplane AWS-8248T & AWS-8248T-T Power supplyAWS-8248TP & AWS-8248TP-T Input voltageRelative humidity 5 ~ 85% @ 40 C, non-condensing Front panel layout Front and rear panel layoutAWS-8248 dimensions DimensionsSystem Setup Detaching the work drawer GeneralDetaching the work drawer Adding cards Installing add-on cardsInstalling optional drives HDD installation Attaching cables Connect the display powerRack mounting the AWS-8248 Rack mountingPanel mounting the AWS-8248 Panel mountingAWS-8248 User’s Manual Maintenance Removing the passive backplane Passive backplaneRemoving the power supply Power supplyRemoving LCD display module first steps LCD display moduleRemoving LCD display module final steps Keyboard translator input/output actual Keyboard translatorKeyboard translator input/output schematic Removing the keyboard translator To service the keyboard translatorRemoving the LED board LED boardRemoving the FDD Floppy disc drive FDDTo replace the function membrane keypad Membrane keypad10 Replacing the membrane keypad Touchscreen sensor -T models 11 Replacing the touchscreen sensor Macro Key Program- ming Macro keys SF1 , SF2, ... SF10 Macro Key ReviewMacro Eeprom Macro programming utilityRelease SyntaxAWS-8248 User’s Manual Macro Editor screen How to use SFED8248.COMExample Key delay ModeSF10 = SF2 = Copy C\CONFIG.EMM C\CONFlG.SYS 33 Y 33 85SF4 = C\WP51\WP3386274D90REPORT.WP533 AWS-8248 User’s Manual OSD Vertical Frequencies Supported Input Timing ModesSel OSD Operation KeypadOSD function and operation Auto-adjustment process or to adjust manuallyPower Supply Specifi- cation Input frequency47 ~ 63 Hz Appendix B Power Supply SpecificationsSpecifications Input voltage 48 V DC power supplyInput current Inrush currentOvershoot resistive load Output characteristicsShort circuit protection Power good and power fail signals optionalOver-current protection Over-voltage protectionOperating temperature Reset timeStorage temperature International Standards Compliance Safety ULAll DC output cables use UL 1007 type wires DC Output wire listRipple and noise 24 VDC power supplyOutput power Power fail signal Power good signalLine regulation Load regulationOutput protection General features EfficiencyInput protection Touchscreen optional Optical ElectricalEnvironmental MechanicalDurability Installation of Touchscreen DriverAWS-8248 User’s Manual

AWS-8248 specifications

The Advantech AWS-8248 is a highly versatile and robust solution tailored for industrial applications, particularly in edge computing, IoT, and automation. This embedded system server is designed to enhance the efficiency of industrial operation by providing high processing power and a multitude of connectivity options.

At the heart of the AWS-8248 lies its Intel Core processor, which delivers substantial computing power, enabling the processing of complex tasks directly at the edge of the network. With a compact design, it fits seamlessly into various industrial environments, optimizing space without compromising on performance. The system supports a wide range of operating systems, including Windows and Linux, ensuring flexibility for developers looking to deploy custom applications.

One of the standout features of the AWS-8248 is its extensive I/O capabilities. It is equipped with multiple USB, COM, and Ethernet ports that facilitate communication with various devices and systems. This connectivity is essential for applications that require real-time data collection and processing. Furthermore, Advantech’s industrial design includes enhanced thermal management, making the AWS-8248 operational in a range of temperatures and suitable for challenging environments.

Built-in support for advanced technologies such as AI and machine learning allows the AWS-8248 to not only perform data collection but also to analyze and derive insights from that data. This capability is particularly valuable in predictive maintenance scenarios, where anticipating equipment failures can save significant costs.

The device’s rugged construction is another significant characteristic. Designed to withstand vibrations, shocks, and dust, the AWS-8248 is ideally suited for deployment in manufacturing, transportation, and other industrial sectors. Compliance with multiple industrial standards ensures reliability and longevity, giving peace of mind to its users.

Moreover, the AWS-8248 is equipped with expansion slots that allow users to customize the device according to their needs. This adaptability ensures that the server can evolve alongside technological advancements and changing industry requirements.

In summary, the Advantech AWS-8248 is a powerful and flexible embedded system that caters to the demanding needs of industrial sectors. With its high-performance processors, extensive connectivity options, rugged design, and support for cutting-edge technologies, it stands out as a premier solution for edge computing and IoT applications. The AWS-8248 promises not just to meet the current demands but also to adapt and grow with future advancements in technology.
Top Page Image Contents