Canon DR-2050C/SP warranty Checking the Accessories, Installing the Software

Installation of the scanner driver starts.

During scanner driver installation, the scanner driver and the Job Registration Tool are installed.

The setup wizard automatically starts up when you insert the CD-ROM into the CD- ROM drive. If the setup wizard does not start up, execute setup.exe in the CD-ROM.

❏

❏

❏ Before installing the software, make sure your computer is correctly running one of the following versions of Windows. For details, refer to the DR-2050C/DR-2050SP User’s Guide.

• Windows 98SE

• Windows Me

• Windows 2000 Professional SP4 or later

• Windows XP Home Edition SP2 or later

• Windows XP Professional SP2 or later

❏ Do not connect the scanner to the computer before installing the software. If you connect the scanner and turn it ON before you install the software, a wizard screen will appear. If this wizard appears, click [Cancel] to exit the wizard, and then turn the scanner OFF.

Wizard Screen (Windows 2000)

Be sure to log on with administrator privileges when logging on to Windows. Close all other applications before installing the software.

Document Scanner DR-2050C/SP

Easy Start Guide

Thank you for purchasing the Canon DR-2050C/DR-2050SP Document Scanner. This Easy Start Guide describes the procedure for setting up the scanner for use. Follow the procedures outlined in this Easy Start Guide to set up the scanner. Details on using the scanner are described in the User’s Guides packaged with the scanner. Before you use the scanner, make sure to thoroughly read the User’s Guides.

Checking the Accessories

When you unpack your scanner, make sure that it contains all of the following accessories. If any of the items listed below are missing or damaged, contact your local authorized Canon dealer or service representative.

		USB Cable
DR-2050C/DR-2050SP	Feed Roller	Type A/Type B	AC Adapter/Power Cord
		(Length: 6 ft. (1.8 m))	(Connected length: 8 ft. 6 in. (2.6 m))

Document	Easy Start Guide	DR-2050C/DR-2050SP	Adjustment Sheet
Guide Adapter	(this document)	User’s Guide

3. Open the front cover at (1) and (2), and remove the orange tape fastening the roller cover.

4. Open the roller cover.

5.Lower the roller lock lever (1), and slide it towards the left (2).

6.Load the feed roller, align the notch on the roller with the shaft on the scanner

Installing the Software

Install the software before connecting the scanner to the computer.

Warning

7.Click [Finish] to complete the installation.

Next, the installation wizard for CapturePerfect 3.0 appears.

8.Click [Next].

9.Read the software license agreement, and click [Yes] if you consent to the conditions of the software.

10.Check the destination folder and click [Next].

DR-2050C	Adobe Acrobat	Warranty Card	Registration Card
Setup Disc	Setup Disc	(U.S.A. and Canada only)	(U.S.A. and Canada only)

*For the DR-2050SP, the following accessories are included in addition to the above items.

DR-2050SP User’s Guide	Remote Control	AAA Batteries (2)	RGB Cable
Presentation Mode Edition			Mini D-sub 15 Pin ⋅ 2
			(Length: 5 ft. (1.5 m))

Note

●To use the feed roller, install it on the scanner.

☞[STEP 2] “Removing the Packing Materials and Installing the Feed Roller”

●Documents can be prevented from feeding slantwise by installing the document guide adapters on the document guides. (☞ STEP 5)

●The adjustment sheet is used to adjust the scanner when anomalies begin to appear in scanned images. Store it in a safe place where it will not be lost.

●The DR-2050 Setup Disc contains the “DR-2050C Scanner Driver”, “CapturePerfect 3.0”, and “OmniPage SE” made by Nuance Communications Inc.

☞DR-2050C/DR-2050SP User’s Guide p.17 “About the Setup Disc”

●Items included in this package are subject to change without notice.

●You must keep the machine’s packaging and packing materials for storing or transporting the machine.

After checking the package contents, you need to prepare the scanner for use. (☞ STEP 2)

Removing the Packing Materials and Installing the Feed Roller

Remove the scanner from the box, remove the orange tape and protective sheets from the scanner, and install the feed roller on the scanner body.

1.Peel off the four pieces of orange tape from the outer casing.

2.Open the document feed tray and remove the protective sheet.

PUB. CE-IE-546 ©2007 CANON ELECTRONICS INC.

body.	1.	Turn ON your computer.
	2.	Insert the DR-2050C Setup Disc into the
		PC’s CD-ROM drive.

7. Slide the roller lock lever towards the right, fit the lever feed roller into the hole on	3. Click [Typical Installation].
the left of the roller (1), and push down the roller lock lever to lock the feed roller
	If you click [Typical Installation], all of the
shaft (2).
	software is installed. If you want to select
	which parts of the software to install, click
	[Custom Installation].

8.	Close the roller cover. Make sure that the roller cover clicks into place.	4. Click [Install].
		All of the currently displayed software is
		installed. To install only selected software,
		click [Back] and select [Custom
		Installation].

9.Gently push in the front unit on its left and right sides to close the front unit.

Make sure that the front unit clicks into place. 5. Click [Next].

10. Close the document feed tray and top cover.

Document Feed Tray	Top Cover	6. Read the software license agreement, and
		click [Yes] if you consent to the conditions of
		the software.

The scanner is now ready for use.

Next, you need to install the scanner software. (☞ STEP 3)

■Trademarks

•Canon and the Canon logo are registered trademarks of Canon Inc. in the United States and may also be trademarks or registered trademarks in other countries.

•Microsoft Windows® is a registered trademark of Microsoft USA in the United States and other countries.

•Other brands and product names used in this manual may be trademarks or registered trademarks of their respective companies.

Installation of CapturePerfect 3.0 starts.

11.Click [Finish] to complete the installation of CapturePerfect 3.0.

12.Next, installation of OmniPage SE starts. Follow the messages on the screen to proceed with the installation.

13.When all installations are complete, the Installation completed screen appears.

Click [Exit] to exit the installer.

(Click [Back] to return to the menu screen.)

14.Remove the setup disc, and finish the

software installation.

Note

●When software is installed the icons are added to the Program menu.

(Windows 2000)

This completes the software installation.

Next, you need to connect the scanner to your computer. (☞ STEP 4)

☞ Continued on back side