Dimensional Drawing, Specifications | EAW AS460e specification

DIMENSIONAL DRAWING

INDICATES MOUNTING POINT, 3/8-16 THREADED HOLE (PI ANGLE)

INDICATES MOUNTING	POINT,
3/8-16 THREADED HOLE	(NUT PLATE).

INDICATES CENTER OF BALANCE.

24.62

22.50

GRILLE PARTIALLY SHOWN

FRONT

SPECIFICATIONS AS460e

A & E SPECIFICATIONS

The bi-amplified or passive mid/high loudspeaker system shall incorporate a horn-loaded 10-in MF cone with Radial Phase Plug™ and a 1.4-in exit/2.5-in voice coil HF neodymi- um compression driver.

The MF driver shall be loaded into a midrange horn construct- ed of 1/8-in birch plywood backed with high density polyurethane foam. The HF driver shall be loaded on a con- stant directivity horn with a nominal coverage pattern of 60°

(h)x 45° (v). An internal passive filter network shall provide fourth order acoustical crossover and system equalization.

System frequency response shall vary no more than ±3 dB from 200 Hz to 15 kHz measured on axis. The mid/high sec- tion shall produce a Sound Pressure Level (SPL) of 107 dB SPL on axis at 1 meter with a power input of 1 Watt and shall be capable of producing a peak output of 139 dB SPL on axis at

(1.50)

19.50

10.50

4.00

6.94

5.00

INPUT

1 meter. The mid frequency section system shall produce a Sound Pressure Level (SPL) of 109 dB SPL on axis at 1 meter with a power input of 1 Watt and shall be capable of produc- ing a peak output of 141 dB SPL on axis at 1 meter. The high frequency section shall produce a Sound Pressure Level (SPL) of 109 dB SPL on axis at 1 meter with a power input of 1 Watt and shall be capable of producing a peak output of 136 dB SPL on axis at 1 meter. The mid/high section shall handle 450 Watts of amplifier power (continuous) and shall have a

		BACK	ACCESS PANEL
		BACK
		(12.29)
	A	10.09
	A	CL
		CL
	12.00		23.00
			16.00
			4.00
A		18.67
		18.67
		30°
		TOP/BOTTOM
		16.56	4.63
			18.60
			CL

	509129 (0)	SIDES
		DIMENSIONS APPLY
	5/10/01
		TO BOTH SIDES

Manufacturing tolerances are +/- 0.13 and +/- 1°

nominal impedance of 8 Ohms. The mid frequency section shall handle 400 Watts of amplifier power. The high frequency section shall handle 125 Watts of amplifier power (continuous) and shall have a nominal impedance of 8 Ohms.

The loudspeaker enclosure shall be trapezoidal in shape. It shall be constructed of multi-ply, void-free, cross-grain-lami- nated, exterior grade, Baltic birch plywood and shall employ extensive internal bracing. It shall be finished in wear-resist- ant textured black paint . Input connectors shall be 2x 6-con- tact terminal barrier strips. Eighteen (18) 3/8"-16 threaded mounting/suspension points (4 each top, bottom and sides, 2 on back) shall be provided. The front of the loudspeaker shall be covered with a powder coated perforated steel grille.

The mid/high loudspeaker shall be the EAW model AS460e.

One	Main Street, Whitinsville, MA 01588	508 234 6158	Toll Free 800 992 5013	FAX 508 234 8251	info@eaw.com	www. eaw. com
EAW	products are continually improved. All specifications are therefore subject to change without notice.			AS460e/2 pp	October 2001	Printed in USA