Output Polarity Switch

%FQFOEJOHPOUIFEJTUBODFSFMBUJPOTIJQ

of the mid-bass speakers and the subwoofers in a system, it can be desirable to reverse the polarity of the subwoofer system in order to produce a better transition between subwoofer and mid-bass speaker output.

5IFiOutput PolaritywTXJUDIBMMPXTZPV

to peform this polarity inversion without removing any wires. Simply flip the switch

GSPNUIFiNormalwUPUIFiReversedwQPTJUJPO

Experiment with this switch to determine which polarity produces the best overall bass performance in your system, listening in particular to the mid-bass smoothness and impact to make your determination.

Subwoofer Output

Output Polarity

NormalReversed

MONO OUTPUT ONLY

STATUS INDICATOR LIGHTS /

PROTECTION CIRCUITRY

There are three status indicator lights on the top of the amplifier. These are as follows:

1)iPowerw (Green): lights to indicate that the amplifier is turned on and operating normally.

2)iThermalw (Red): lights to indicate that the amplifier has exceeded its safe operating temperature, putting the amplifier into a self- protection mode, which reduces the power output of the amplifier. The red light will shut off and the amplifier will return to normal, full-power operating mode if the heat sink temperature drops back to a safe level.

3)iLow Ωw (Amber): lights to indicate that the impedance of the speaker load connected to the amplifier is lower than the optimum impedance load range for the amplifier. When this light is on, a protection circuit engages and reduces the power output of the amplifier. The amber indicator will also light when a short-circuit is detected in the speaker wiring (this can be a short between the positive and negative speaker wires or between either speaker wire and the vehicle chassis).

4)“Low V” (Blue): lights to indicate any dip in supply voltage below 8 volts. The

CMVF-&%XJMMSFNBJOMJUMPOHFSUIBOUIF dip duration to better alert the user to the problem. This will be accompanied by a shutdown of the amplifier (green LED will shut off) and a total loss of output.

Once the voltage rises above 9 volts, the amplifier will turn itself on. Because voltage dips occur in rapid succession, the typical behavior will be a cycling of the amplifier on and off, accompanied by flashing of the

“Low V”CMVF-&%*GUIJTJTIBQQFOJOHJOyour system, you will need to investigate the cause of the voltage problem. This could be a bad ground on the amplifier, battery or alternator OR a faulty battery/charging system OR a problem with a fuse holder or wire connection.

If you are unsure as to the cause of the problem, please consult your JL Audio dealer or a qualified automotive electrical specialist.

Keep in mind that any large amplifier, like the 1000/1, places a very heavy demand on a vehicle’s charging system when operated at its limits.

Vehicles with weak charging systems may need to be serviced and/or upgraded to provide ample current to a system including a 1000/1.

There is only one condition that will shut down

BOVOEBNBHFEWDPNQMFUFMZy*GCBUUFSZ

voltage drops below 10 volts, the entire amplifier

XJMMTIVUJUTFMGPGG5IFHSFFOiPowerwJOEJDBUPS

on the top of the amplifier will turn off when this occurs. The amplifier will turn back on when voltage climbs back above 10 volts. This may happen in a rapid cycle when bass-heavy program material causes a weak charging system to dip below 10 volts momentarily. If this is happening in your system, have your charging system inspected to make sure it is working properly.

For information on troubleshooting this amplifier, refer to Appendix E (page 21).

SERVICING YOUR JL AUDIO AMPLIFIER

If your amplifier fails or malfunctions, please

SFUVSOJUUPZPVSBVUIPSJ[FE+-"VEJPEFBMFSTP

that it may be sent in to JL Audio for service. There are no user serviceable parts or fuses inside the amplifier. The unique nature of the circuitry in the JL Audio amplifiers requires specifically

USBJOFETFSWJDFQFSTPOOFM%POPUBUUFNQU

to service the amplifier yourself or through

VOBVUIPSJ[FESFQBJSGBDJMJUJFT5IJTXJMMOPUPOMZ

void the warranty, but may result in the creation of more problems within the amplifier.

If you have any questions about the installation or setup of the amplifier not covered in this manual, please contact your dealer or technical support.

JL Audio Technical Support:

(954) 443-1100

9:00 AM – 5:30 PM (Eastern Time Zone)

Monday - Friday

12 JL Audio - 1000/1v2 Owner’s Manual

1000/1v2 specifications

The JL Audio 1000/1v2 is a standout monoblock amplifier designed to deliver exceptional power and sound quality for subwoofer applications. Renowned for its innovative technology and reliability, this amplifier is the choice of many audiophiles and car audio enthusiasts looking for premium performance.

One of the most notable features of the 1000/1v2 is its high power output. With a maximum continuous output of 1,000 watts at 2 ohms, this amplifier is capable of driving even the most demanding subwoofers with ease. The amplifier is engineered to provide clean and efficient power, minimizing distortion and maximizing the audio experience.

The 1000/1v2 incorporates JL Audio's proprietary Class D technology, which enables it to achieve high power levels without the excessive heat generation typically associated with traditional amplifiers. This not only improves the amplifier's efficiency but also enhances its durability, allowing it to perform optimally under various conditions.

Another key aspect of the 1000/1v2 is its advanced signal processing capabilities. It features a built-in low-pass filter with adjustable cutoff points, allowing users to customize the frequency response to suit their specific audio systems. Additionally, the amplifier includes a patented differential-balanced input section that ensures a clean, noise-free signal, which is crucial for achieving high-quality sound reproduction.

The JL Audio 1000/1v2 also offers comprehensive control options. Its user-friendly interface features a gain control, a bass boost knob, and phase adjustment, all of which empower users to tweak the sound output to their liking. Moreover, it is equipped with a remote level control feature, enabling adjustments from the driver's seat for added convenience.

Notably, this amplifier features a robust and stylish design, equipped with a durable aluminum chassis that not only looks appealing but also aids in heat dissipation. The various protection circuits built into the 1000/1v2 safeguard the amplifier and connected components against issues such as overheating, short circuits, and overloading, ensuring longevity and reliability.

In conclusion, the JL Audio 1000/1v2 is an exceptional choice for those seeking a powerful and versatile monoblock amplifier. With its impressive output, innovative technology, and user-friendly features, it stands out as a top contender in the competitive world of car audio amplification. Whether for casual listening or high-performance sound setups, the 1000/1v2 delivers an audio experience that is both exhilarating and immersive.