NuTone installation instructions Accessory Switch, Model HS-93, Installation

Page 1

®

READ AND SAVE THESE

INSTALLATION INSTRUCTIONS!

Accessory Switch

MODEL: HS-93

 

 

 

 

 

 

 

LIGHT VENT HEAT

 

INSTALLATION

 

 

 

Used with Heat–Vent–Light

 

 

COMMON

Combination.

 

 

 

 

 

 

 

1.

Install a double–gang box.

 

 

 

 

 

2.

Refer to Figure 1. Run power wiring

 

 

 

 

 

 

from fuse box or circuit breaker and

 

 

 

 

 

 

wiring from heat–vent–light wires to

 

 

LIGHT

 

 

 

outlet box.

 

 

 

 

 

3.

Secure all wires to outlet box with an

 

 

 

 

 

 

approved box connector.

 

 

VENT

 

 

4.

Dress all leads, leaving

 

 

 

BLACK

WHITE

 

approximately 1/2" of bare wire for

 

 

HEAT

 

 

 

 

 

 

making connections.

 

 

 

 

 

5.

Refer to Figure 1. Make wire

 

 

 

 

 

 

connections. Observe cover plate

TO

120vAC, 60Hz

 

 

 

markings (Heat–Vent–Light) when

 

 

 

HOUSE POWER

 

FIGURE 1

 

making connections. Make sure that

 

 

 

 

 

the switch and the unit it controls are properly grounded.

6.Refer to Figure 2. Using two supplied screws, secure switch bracket assembly to outlet box adapter plate.

7.Position wall plate over switch assembly and secure with supplied screws.

®

READ AND SAVE THESE

INSTALLATION INSTRUCTIONS!

Accessory Switch

MODEL: HS-93

 

 

 

 

 

 

 

LIGHT VENT HEAT

 

INSTALLATION

 

 

 

Used with Heat–Vent–Light

 

 

COMMON

Combination.

 

 

 

 

 

 

 

1.

Install a double–gang box.

 

 

 

 

 

2.

Refer to Figure 1. Run power wiring

 

 

 

 

 

 

from fuse box or circuit breaker and

 

 

 

 

 

 

wiring from heat–vent–light wires to

 

 

LIGHT

 

 

 

outlet box.

 

 

 

 

 

3.

Secure all wires to outlet box with an

 

 

 

 

 

 

approved box connector.

 

 

VENT

 

 

4.

Dress all leads, leaving

 

 

 

BLACK

WHITE

 

approximately 1/2" of bare wire for

 

 

HEAT

 

 

 

 

 

 

making connections.

 

 

 

 

 

5.

Refer to Figure 1. Make wire

 

 

 

 

 

 

connections. Observe cover plate

TO

120vAC, 60Hz

 

 

 

markings (Heat–Vent–Light) when

 

 

 

HOUSE POWER

 

FIGURE 1

 

making connections. Make sure that

 

 

 

 

 

the switch and the unit it controls are properly grounded.

6.Refer to Figure 2. Using two supplied screws, secure switch bracket assembly to outlet box adapter plate.

7.Position wall plate over switch assembly and secure with supplied screws.

TO UNIT

2 GANG

BOX

ADAPTER PLATE

USE A SINGLE-GANG BOX ADAPTER PLATE TO COVER DOUBLE GANG BOX. ADAPTER PLATE NOT SUPPLIED WITH SWITCH.

TO UNIT

2 GANG

BOX

ADAPTER PLATE

USE A SINGLE-GANG BOX ADAPTER PLATE TO COVER DOUBLE GANG BOX. ADAPTER PLATE NOT SUPPLIED WITH SWITCH.

TO 120vAC,

 

60Hz HOUSE POWER

FIGURE 2

 

TO 120vAC,

 

60Hz HOUSE POWER

FIGURE 2

 

Image 1
Contents Read and Save These Installation Instructions Accessory SwitchInstallation Model HS-93If YOU Need Assistance or Service One Year Limited WarrantyResidents of the contiguous United States Dial Free